For SOCs with GFX v9.4.3, a VF may have multiple compute partitions.
Fetch the partition information during init and initialize partition
nodes. There is no support to switch partition mode in VF mode, hence
disable the same.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
to avoid reading wrong WPTR from doorbell in sriov vf, set
CP_HQD_PQ_DOORBELL_CONTROL.DOORBELL_MODE to 1 to read WPTR from MQD.
Signed-off-by: Zhigang Luo <Zhigang.Luo@amd.com>
Acked-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
sriov has the higher bit violation when flushing tlb
[HOW]
normalize the registers to keep lower 16-bit(dword aligned) to aviod higher bit violation
RLCG will mask xcd out and always assume it's accessing its own xcd
v2
add check in wait mem that only do the normalization on regspace
Signed-off-by: Jane Jian <Jane.Jian@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Yiqing Yao <YiQing.Yao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To achieve full occupancy CP hardware needs to know if CUs in SE are
symmetrically or asymmetrically harvested
v2: Reset is_symmetric_cus for each loop
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v1
- driver MMIO read the register to check whether write is required
- if write is required, sriov full time to use rlcg, otherwise use KIQ
v2
- include gfx v11 sriov runtime case
Signed-off-by: Jane Jian <Jane.Jian@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The function gfx_v9_4_3_init_microcode in gfx_v9_4_3.c was generating
about potential truncation of output when using the snprintf function.
The issue was due to the size of the buffer 'ucode_prefix' being too
small to accommodate the maximum possible length of the string being
written into it.
The string being written is "amdgpu/%s_mec.bin" or "amdgpu/%s_rlc.bin",
where %s is replaced by the value of 'chip_name'. The length of this
string without the %s is 16 characters. The warning message indicated
that 'chip_name' could be up to 29 characters long, resulting in a total
of 45 characters, which exceeds the buffer size of 30 characters.
To resolve this issue, the size of the 'ucode_prefix' buffer has been
reduced from 30 to 15. This ensures that the maximum possible length of
the string being written into the buffer will not exceed its size, thus
preventing potential buffer overflow and truncation issues.
Fixes the below with gcc W=1:
drivers/gpu/drm/amd/amdgpu/gfx_v9_4_3.c: In function ‘gfx_v9_4_3_early_init’:
drivers/gpu/drm/amd/amdgpu/gfx_v9_4_3.c:379:52: warning: ‘%s’ directive output may be truncated writing up to 29 bytes into a region of size 23 [-Wformat-truncation=]
379 | snprintf(fw_name, sizeof(fw_name), "amdgpu/%s_rlc.bin", chip_name);
| ^~
......
439 | r = gfx_v9_4_3_init_rlc_microcode(adev, ucode_prefix);
| ~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/gfx_v9_4_3.c:379:9: note: ‘snprintf’ output between 16 and 45 bytes into a destination of size 30
379 | snprintf(fw_name, sizeof(fw_name), "amdgpu/%s_rlc.bin", chip_name);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/gfx_v9_4_3.c:413:52: warning: ‘%s’ directive output may be truncated writing up to 29 bytes into a region of size 23 [-Wformat-truncation=]
413 | snprintf(fw_name, sizeof(fw_name), "amdgpu/%s_mec.bin", chip_name);
| ^~
......
443 | r = gfx_v9_4_3_init_cp_compute_microcode(adev, ucode_prefix);
| ~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/gfx_v9_4_3.c:413:9: note: ‘snprintf’ output between 16 and 45 bytes into a destination of size 30
413 | snprintf(fw_name, sizeof(fw_name), "amdgpu/%s_mec.bin", chip_name);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 8630112969 ("drm/amdgpu: split gc v9_4_3 functionality from gc v9_0")
Cc: Hawking Zhang <Hawking.Zhang@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Suggested-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add the prototype to dump ip registers
for all ips of different asics and set
them to NULL for now. Based on the
requirement add a function pointer for
each of them.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add new types to distinguish between ACA error type and smu mca type.
e.g.:
the ACA_ERROR_TYPE_DEFERRED is not matched any smu mca valid bank
channel, so add new type 'aca_smu_type' to distinguish aca error type
and smu mca type.
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix a memory overflow issue in the gfx IB test
for some ASICs. At least 20 bytes are needed for
the IB test packet.
v2: correct code indentation errors. (Christian)
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_kiq_wreg/rreg is hardcoded to use MEC engine 0.
Add an xcc_id parameter to amdgpu_kiq_wreg/rreg, define W/RREG32_XCC
and amdgpu_device_xcc_wreg/rreg to use the new xcc_id parameter.
Using amdgpu_sriov_runtime to determine whether to access via kiq or
RLC is sufficient for now.
v5: add condition in amdgpu_device_xcc_w/rreg, remove trace func call
v4: avoid using amdgpu_sriov_w/rreg
v3: use W/RREG32_XCC to handle non-kiq case
v2: define amdgpu_device_xcc_wreg/rreg instead of changing parameters
of amdgpu_device_wreg/rreg
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, we store CU info only for a single XCC assuming
that it is the same for all XCCs. However, that may not be
true. As a result, store CU info for all XCCs. This info is
later used for CU masking.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
gfx_v9_4_3_ue|ce_reg_list is an array per gfx core instance
correct the settings of se_num and reg_inst for some of
gfx ras counters so all the available register instances
can be polled for ras status.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On GFX v9.4.3, compute queue MQD is populated using the values in HQD
persistent state register. Hence don't clear the values on module
unload, instead restore it to the default reset value so that MQD is
initialized correctly during next module load. In particular, preload
flag needs to be set on compute queue MQD, otherwise it could cause
uninitialized values being used at device reset state resulting in EDC.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In case that the GET_INST() is used for looping, only loops for the
times of actual num of xcc, otherwise GET_INST() will return the invalid
index, a.k.a -1
And also remove the redundant mask checking in case of GET_INST()
Signed-off-by: Shiwu Zhang <shiwu.zhang@amd.com>
Reviewed-by: Le Ma <le.ma@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
XCP_CTL register is expected to be programmed by firmware. Under certain
conditions FW may not have programmed it correctly. As a workaround,
program it when FW has not programmed the right values.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add RLCG interface support for gfx v9.4.3 and multiple XCCs.
Do not enable it yet.
v2: Fix amdgpu_rlcg_reg_access_ctrl init, add support for multiple XCCs
in amdgpu_mm_wreg_mmio_rlc
v3: Use GET_INST() when indexing amdgpu_rlcg_reg_access_ctrl
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Zhigang Luo <zhigang.luo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
