The DP 1.4 spec defines the SDP header and SDP contents for
a Picture Parameter Set (PPS) that must be sent in advance
of DSC transmission to define the encoding characteristics.
This was done in one struct, drm_dsc_pps_infoframe, which
conatined the SDP header and PPS. Because the PPS is
a property of DSC over any connector, not just DP, and because
drm drivers may have their own SDP structs they wish to use,
make the functions that initialise SDP and PPS headers take
the components they operate on, not drm_dsc_pps_infoframe,
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190221202001.28430-4-David.Francis@amd.com
Native 420 and 422 transfer modes are new in DSC1.2
In these modes, each two pixels of a slice are treated as one
pixel, so the slice width is half as large (round down) for
the purposes of calucating the groups per line and chunk size
in bytes
In native 422 mode, each pixel has four components, so the
mux component of a group is larger by one additional mux word
and one additional component
Now that there is native 422 support, the configuration option
previously called enable422 is renamed to simple_422 to avoid
confusion
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190221202001.28430-3-David.Francis@amd.com
There is a really hairy resolution involving amdgpu fixes, that I'd rather confirm here.
Also some misc fixes are landed by me, but the pr has them as well.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch attaches the colorspace connector property to the
hdmi connector. Based on colorspace change, modeset will be
triggered to switch to new colorspace.
Based on colorspace property value create an infoframe
with appropriate colorspace. This can be used to send an
infoframe packet with proper colorspace value set which
will help to enable wider color gamut like BT2020 on sink.
This patch attaches and enables HDMI colorspace, DP will be
taken care separately.
v2: Merged the changes of creating infoframe as well to this
patch as per Maarten's suggestion.
v3: Addressed review comments from Shashank. Separated HDMI
and DP colorspaces as suggested by Ville and Maarten.
v4: Addressed Chris and Ville's review comments, and created a
common colorspace property for DP and HDMI, filtered the list
based on the colorspaces supported by the respective protocol
standard. Handle the default case properly.
v5: Merged the DP handling along with platform colorspace
handling as per Shashank's comments.
v6: Reverted to old design of exposing all colorspaces to
userspace as per Ville's review comment
v7: Fixed a checkpatch complaint, Addressed Maarten' review
comment, updated the RB from Maarten and Jani's ack.
v8: Moved colorspace AVI Infoframe programming to drm core and
removed from driver as per Ville's suggestion.
v9: Added a check to only allow RGB colorpsaces to be set in
infoframe though the colorspace property. Since there is no output
csc property to control planar formats and it will be added later.
Changes for RGB->YUV conversion inside driver without userspace
knowledge is still supported. This is as per Ville's suggestion.
v10: Fixed an error in if check.
v11: Dropped the check for planar vs RGB and allow all the colorspaces.
Onus will be on userspace to pick whatever pipe output it is able to
drive.
v12: Added Ville's RB.
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1550596381-993-4-git-send-email-uma.shankar@intel.com
When resuming, we check whether or not any previously connected
MST topologies are still present and if so, attempt to resume them. If
this fails, we disable said MST topologies and fire off a hotplug event
so that userspace knows to reprobe.
However, sending a hotplug event involves calling
drm_fb_helper_hotplug_event(), which in turn results in fbcon doing a
connector reprobe in the caller's thread - something we can't do at the
point in which i915 calls drm_dp_mst_topology_mgr_resume() since
hotplugging hasn't been fully initialized yet.
This currently causes some rather subtle but fatal issues. For example,
on my T480s the laptop dock connected to it usually disappears during a
suspend cycle, and comes back up a short while after the system has been
resumed. This guarantees pretty much every suspend and resume cycle,
drm_dp_mst_topology_mgr_set_mst(mgr, false); will be caused and in turn,
a connector hotplug will occur. Now it's Rute Goldberg time: when the
connector hotplug occurs, i915 reprobes /all/ of the connectors,
including eDP. However, eDP probing requires that we power on the panel
VDD which in turn, grabs a wakeref to the appropriate power domain on
the GPU (on my T480s, this is the PORT_DDI_A_IO domain). This is where
things start breaking, since this all happens before
intel_power_domains_enable() is called we end up leaking the wakeref
that was acquired and never releasing it later. Come next suspend/resume
cycle, this causes us to fail to shut down the GPU properly, which
causes it not to resume properly and die a horrible complicated death.
(as a note: this only happens when there's both an eDP panel and MST
topology connected which is removed mid-suspend. One or the other seems
to always be OK).
We could try to fix the VDD wakeref leak, but this doesn't seem like
it's worth it at all since we aren't able to handle hotplug detection
while resuming anyway. So, let's go with a more robust solution inspired
by nouveau: block fbdev from handling hotplug events until we resume
fbdev. This allows us to still send sysfs hotplug events to be handled
later by user space while we're resuming, while also preventing us from
actually processing any hotplug events we receive until it's safe.
This fixes the wakeref leak observed on the T480s and as such, also
fixes suspend/resume with MST topologies connected on this machine.
Changes since v2:
* Don't call drm_fb_helper_hotplug_event() under lock, do it after lock
(Chris Wilson)
* Don't call drm_fb_helper_hotplug_event() in
intel_fbdev_output_poll_changed() under lock (Chris Wilson)
* Always set ifbdev->hpd_waiting (Chris Wilson)
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 0e32b39cee ("drm/i915: add DP 1.2 MST support (v0.7)")
Cc: Todd Previte <tprevite@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v3.17+
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190129191001.442-2-lyude@redhat.com
(cherry picked from commit fe5ec65668)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Enable count array is supposed to have one counter for each possible
engine sampler. As such, array sizing and bounds checking is not correct
and would blow up the asserts if more samplers were added.
No ill-effect in the current code base but lets fix it for correctness.
At the same time tidy the assert for readability and robustness.
v2:
* One check per assert. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: b46a33e271 ("drm/i915/pmu: Expose a PMU interface for perf queries")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190205130353.21105-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit 26a11deea6)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Split the color management hooks along the single vs. double
buffered registers line. Of the currently programmed registers
GAMMA_MODE and the ilk+ pipe CSC are double buffered, the
LUTS and CHV CGM block are single buffered.
The double buffered register will be programmed during the
normal pipe update with evasion, and also during pipe enable
so that the settings will already be correct when the pipe
starts up before the planes are enabled.
The single buffered registers are currently programmed before
the vblank evade. Which is totally wrong, but we'll correct
that later.
v2: Add some docs to explain the two vfuncs (Matt,Uma)
Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190205160848.24662-6-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
On g4x+ the pipe gamma enable bit for the primary plane affects
the pipe bottom color as well. The same for the pipe csc enable
bit on ilk+. Thus we must configure those bits correctly even
when the primary plane is disabled.
To make the feasible let's split those settings from the
plane_ctl() function into a seprate funciton that we can
call from the ->disable_plane() hook as well.
For consistency we'll do that on all the plane types. While
that has no real benefits at this time, it'll become useful
when we start to control the pipe gamma/csc enable bits
dynamically when we overhaul the color management code.
On pre-g4x there doesn't appear to be any way to gamma
correct the pipe bottom color, but sticking to the same
pattern doesn't hurt. And it'll still help us to do
crtc state readout correctly for the pipe gamma enable
bit for the color management overhaul.
An alternative apporach would be to still precompute these
bits into plane_state->ctl, but that would require that we
run through the plane check even when the plane isn't logically
enabled on any crtc. Currently that condition causes us to
short circuit the entire thing and not call ->check_plane().
There would also be some chicken and egg problems with
->check_plane() vs. crtc color state check that would
requite splitting certain things into multiple steps.
So all in all this seems like the easier route.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190205160848.24662-2-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
update_wm_post is meant for pre-g4x only. Don't ever set
it on g4x+.
The only effect of a bogus update_wm_post on g4x+ could
be that we clear the legacy_cursor_update flag in
intel_atomic_commit(). Since legacy_cursor_update is
only set for legacy cursor updates (as the name suggests)
and we only set update_wm_post for a modeset the two
cases should never occur at the same time. But let's
be consistent in setting update_wm_post so we don't
end up confusing so many people.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190206185433.8116-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Apply backpressure to hogs that emit requests faster than the GPU can
process them by waiting for their ring to be less than half-full before
proceeding with taking the struct_mutex.
This is a gross hack to apply throttling backpressure, the long term
goal is to remove the struct_mutex contention so that each client
naturally waits, preferably in an asynchronous, nonblocking fashion
(pipelined operations for the win), for their own resources and never
blocks another client within the driver at least. (Realtime priority
goals would extend to ensuring that resource contention favours high
priority clients as well.)
This patch only limits excessive request production and does not attempt
to throttle clients that block waiting for eviction (either global GTT or
system memory) or any other global resources, see above for the long term
goal.
No microbenchmarks are harmed (to the best of my knowledge).
Testcase: igt/gem_exec_schedule/pi-ringfull-*
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190207071829.5574-1-chris@chris-wilson.co.uk
We have a bad habit of calling drm_fb_helper_hotplug_event() far more
then we actually need to. MST appears to be one of these cases, where we
call drm_fb_helper_hotplug_event() if we fail to resume a connected MST
topology in intel_dp_mst_resume(). We don't actually need to do this at
all though since hotplug events are already sent from
drm_dp_connector_destroy_work() every time connectors are unregistered
from userspace's PoV. Additionally, extra calls to
drm_fb_helper_hotplug_event() also just mean more of a chance of doing a
connector probe somewhere we shouldn't.
So, don't send any hotplug events during resume if the MST topology
fails to come up. Just rely on the DP MST helpers to send them for us.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190129191001.442-3-lyude@redhat.com
When resuming, we check whether or not any previously connected
MST topologies are still present and if so, attempt to resume them. If
this fails, we disable said MST topologies and fire off a hotplug event
so that userspace knows to reprobe.
However, sending a hotplug event involves calling
drm_fb_helper_hotplug_event(), which in turn results in fbcon doing a
connector reprobe in the caller's thread - something we can't do at the
point in which i915 calls drm_dp_mst_topology_mgr_resume() since
hotplugging hasn't been fully initialized yet.
This currently causes some rather subtle but fatal issues. For example,
on my T480s the laptop dock connected to it usually disappears during a
suspend cycle, and comes back up a short while after the system has been
resumed. This guarantees pretty much every suspend and resume cycle,
drm_dp_mst_topology_mgr_set_mst(mgr, false); will be caused and in turn,
a connector hotplug will occur. Now it's Rute Goldberg time: when the
connector hotplug occurs, i915 reprobes /all/ of the connectors,
including eDP. However, eDP probing requires that we power on the panel
VDD which in turn, grabs a wakeref to the appropriate power domain on
the GPU (on my T480s, this is the PORT_DDI_A_IO domain). This is where
things start breaking, since this all happens before
intel_power_domains_enable() is called we end up leaking the wakeref
that was acquired and never releasing it later. Come next suspend/resume
cycle, this causes us to fail to shut down the GPU properly, which
causes it not to resume properly and die a horrible complicated death.
(as a note: this only happens when there's both an eDP panel and MST
topology connected which is removed mid-suspend. One or the other seems
to always be OK).
We could try to fix the VDD wakeref leak, but this doesn't seem like
it's worth it at all since we aren't able to handle hotplug detection
while resuming anyway. So, let's go with a more robust solution inspired
by nouveau: block fbdev from handling hotplug events until we resume
fbdev. This allows us to still send sysfs hotplug events to be handled
later by user space while we're resuming, while also preventing us from
actually processing any hotplug events we receive until it's safe.
This fixes the wakeref leak observed on the T480s and as such, also
fixes suspend/resume with MST topologies connected on this machine.
Changes since v2:
* Don't call drm_fb_helper_hotplug_event() under lock, do it after lock
(Chris Wilson)
* Don't call drm_fb_helper_hotplug_event() in
intel_fbdev_output_poll_changed() under lock (Chris Wilson)
* Always set ifbdev->hpd_waiting (Chris Wilson)
Signed-off-by: Lyude Paul <lyude@redhat.com>
Fixes: 0e32b39cee ("drm/i915: add DP 1.2 MST support (v0.7)")
Cc: Todd Previte <tprevite@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v3.17+
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190129191001.442-2-lyude@redhat.com
Enable count array is supposed to have one counter for each possible
engine sampler. As such, array sizing and bounds checking is not correct
and would blow up the asserts if more samplers were added.
No ill-effect in the current code base but lets fix it for correctness.
At the same time tidy the assert for readability and robustness.
v2:
* One check per assert. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: b46a33e271 ("drm/i915/pmu: Expose a PMU interface for perf queries")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190205130353.21105-1-tvrtko.ursulin@linux.intel.com
Certain SNB machines (eg. ASUS K53SV) seem to have a broken BIOS
which misprograms the hardware badly when encountering a suitably
high resolution display. The programmed pipe timings are somewhat
bonkers and the DPLL is totally misprogrammed (P divider == 0).
That will result in atomic commit timeouts as apparently the pipe
is sufficiently stuck to not signal vblank interrupts.
IIRC something like this was also observed on some other SNB
machine years ago (might have been a Dell XPS 8300) but a BIOS
update cured it. Sadly looks like this was never fixed for the
ASUS K53SV as the latest BIOS (K53SV.320 11/11/2011) is still
broken.
The quickest way to deal with this seems to be to shut down
the pipe+ports+DPLL. Unfortunately doing this during the
normal sanitization phase isn't quite soon enough as we
already spew several WARNs about the bogus hardware state.
But it's better than hanging the boot for a few dozen seconds.
Since this is limited to a few old machines it doesn't seem
entirely worthwile to try and rework the readout+sanitization
code to handle it more gracefully.
v2: Fix potential NULL deref (kbuild test robot)
Constify has_bogus_dpll_config()
Cc: stable@vger.kernel.org # v4.20+
Cc: Daniel Kamil Kozar <dkk089@gmail.com>
Reported-by: Daniel Kamil Kozar <dkk089@gmail.com>
Tested-by: Daniel Kamil Kozar <dkk089@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109245
Fixes: 516a49cc19 ("drm/i915: Fix assert_plane() warning on bootup with external display")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190111174950.10681-1-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
(cherry picked from commit 7bed8adcd9)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190205141846.6053-1-ville.syrjala@linux.intel.com
