[Why]
These registers should not be read from driver and triggering the
security violation when DMCUB work times out and diagnostics are
collected blocks Z8 entry.
[How]
Remove the register read from DCN35.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPD sense changes can occur during low power states and need to be
notified from firmware to driver. Upon notification the hotplug
redetection routines should execute.
[How]
Add Support in DMUB srv and DMUB srv stat for receiving these
notifications. DM can hook them up and process the HPD redetection
once received.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We can hang in IPS2 checking DMCUB_SCRATCH0 for link detection state.
[How]
Replace the HW access with a check on the shared state bit. This will
work the same way as the SCRATCH0 but won't require a wake in the case
where link detection isn't required.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Add logging for first DMUB inbox message that timed out to diagnostic
data
- It is useful to track the first failed message for debug purposes
because once DMUB becomes hung (typically on a message), it will
remain hung and all subsequent messages. In these cases we're
interested in knowing which is the first message that failed.
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VBIOS DMCUB firmware doesn't set the dal_fw bit and we end up hanging
waiting for HW power up done because of it.
[How]
Simplify the path and allow mailbox_rdy to be a functional check when
we detect VBIOS firmware.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Read modify write hazards can occur when using a single shared scratch
register between driver and firmware leading to driver accessing DCN
in IPS2 and a system hang.
[How]
Add infrastructure for using REGION6 as a shared firmware state between
driver and firmware. This region is uncachable.
Replace the existing get/set idle calls with reads/writes to the
(volatile) shared firmware state blocks that a separated by at least
a cache line between firmware and driver.
Remove the workarounds that required rewriting/checking read modify
write hazards.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Display code keeps getting improvements, and because of that, some
legacy code is left behind. This commit drops some of those unused
codes.
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On resume from S3, while DMUB is inactive, DMUB queue and execute
calls will not work. Skip reporting errors in these scenarios
[How]
Add new return code during DMUB queue and execute calls when DMUB
is in S3 state. Skip logging errors in these scenarios
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On resume from S3, may get apply_idle_optimizations call while DMUB
is inactive which will just time out.
[How]
Set and track power state in dmub_srv and check power state before
sending commands to DMUB. Add interface in both dmub_srv and
dc_dmub_srv
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need a helper function to check idle power is allowed
so that dc doesn't access any registers that are power-gated.
[how]
Implement helper function to check idle power optimization.
Enable a hook to check if detection is allowed.
V2:
Add function hooks for set and get idle states.
Check if function hook was properly initialized.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Choi <nicholas.choi@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need a helper function to check idle power is allowed
so that dc doesn't access any registers that are power-gated.
[how]
Implement helper function to check idle power optimization.
Enable a hook to check if detection is allowed.
Signed-off-by: Sung Joon Kim <Sungjoon.Kim@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drivers/gpu/drm/amd/amdgpu/../display/dmub/src/dmub_srv.c:355 dmub_srv_hw_setup() warn: inconsistent indenting
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
SubVP needs to "calculate" the earliest in use META address
by using the current primary / meta addresses, but this leads
to a race condition where FW and driver can read/write the
address at the same time and intermittently produce inconsistent
address offsets. To mitigate this issue without locking (too slow),
save each surface flip addr into scratch registers and use this
to keep track of the earliest in use META addres.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
DMUB subsystem was continuing to use compile time offset calculation for
register access. Switch this to runtime calculation to stay consistent
with rest of DC code.
To enable this, an additional interface init_reg_offsets() are added to
DMUB's hw_funcs struct. Asics with runtime register offset calculation
enabled shall populate this hook with a fn pointer that will invoke the
necessary macros to calculate the offset.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This option can vary depending on the panel and may be required to be
called during sink detection phase before transmitter control.
[How]
Allow modify the bit depending on the eDP panel connected with a new
interface.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If optimized init is done in FW. DCN init can be skipped in driver. This
need to be communicated between driver and fw and maintain backwards
compatibility.
[How]
Use DMUB scratch 0 bit 2 to indicate optimized init done in fw and
use DMUB scatch 4 bit 0 to indicate drive supports the optimized flow
so FW will perform it.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Otherwise we can be out of sync with what's in the hardware, leading
to us rerunning every command that's presently in the ringbuffer.
[How]
Reset software state for the mailboxes in hw_reset callback.
This is already done as part of the mailbox init in hw_init, but we
do need to remember to reset the last cached wptr value as well here.
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Adding the new DPIA NOTIFY packets from DMUB
As per the design with Cruise to account for
250ms response delay otherwise
[HOW]
Added th DPIA NOTIFY logic as per DMUB logic
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Mustapha Ghaddar <mghaddar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Dpia hpd interrupt processing is disabled when entering S4/S0i3 and
would be reenabled after detection completes during resuming. Because,
keeping hpd interrupts enabled during detection leads to multiple
detections for the same hpd transition. There is a S4 case where dpia
hpd interrupt is missed when driver is in transitioning from hpd
interrupt processing disable to enable and the display does not light
up.
[How]
- Added dmub inbox command DMUB_CMD__DPIA_HPD_INT_ENABLE to explicitly
control dmub to issue dpia hpd interrupt or not. If dpia hpd interrupt
is disabled, dmub will keep the hpd pending and post it once driver
reenables dpia hpd interrupt or when querying with
DMUB_CMD__QUERY_HPD_STATE.
- Added dmub boot option dpia_hpd_int_enable_supported to notify dmub
about whether DMUB_CMD__DPIA_HPD_INT_ENABLE command would be used.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Mustapha Ghaddar <Mustapha.Ghaddar@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit cleans up code that uses old variables and adds some SMU
interfaces for future flexibility.
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
