The HDMI WP timings are not programmed correctly for interlace.
We need to halve the vertical timings when interlace is used, and double
the horizontal timings when pixel doubling is used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
On OMAP4 and OMAP5 ES1.0 the HDMI_WP_VIDEO_TIMING_H:HSW field is
set directly to the HSW value. On later SoCs the field needs to be
programmed with the value of HSW-1.
Currently the driver always programs the field with the HSW value. Most
videomodes seem to work fine with that, but at least low resolution
interlaced modes don't work at all.
This patch fixes the HSW for OMAP5 ES2.0+ SoCs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We need double-pixel mode (pixel repetition) for interlace modes. This
patch adds the necessary support to HDMI to double the pixel clock when
double-pixel mode is used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We need double-pixel mode (pixel repetition) for interlace modes. This
patch adds the necessary support to omapdrm to output double-pixel mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We need double-pixel mode (pixel repetition) for interlace modes. This
patch adds the necessary support to DISPC to output double-pixel mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_crtc_wait_pending() waits until the config changes have been taken
into use, usually at next vblank. The wait-timeout used is 50ms, which
usually is enough, but in some rare cases not.
As time wait-timeout is just a safety measure for cases where something
is broken, we can just as well increase the timeout considerably.
This patch makes the timeout 250ms.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We no longer have the omapdrm plugin system for SGX, and we can thus
remove the support for external memory and sync objects from omap_gem.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
OMAP GEM objects backed by dma_buf reuse the current OMAP GEM object
support as much as possible. If the imported buffer is physically
contiguous its physical address will be used directly, reusing the
OMAP_BO_MEM_DMA_API code paths. Otherwise it will be mapped through the
TILER using a pages list created from the scatterlist instead of the
shmem backing storage.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Split the individual steps of GEM object allocation and initialization
clearly. This improves readability and prepares for dma_buf import
support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver assumes that only objects backed by shmem need to be mapped
through DMM. While this is true with the current code, the assumption
won't hold with dma_buf import support.
Condition the mapping based on whether the buffer has been allocated
using the DMA mapping API instead and clean up the flags to avoid having
to check both flags and GEM object filp field to decide how to process
buffers. Flags are not the authoritative source of information regarding
where the buffer memory comes from, and are renamed to make that
clearer.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the panel's enable fails, omap_encoder silently ignores the failure.
omapdrm should really handle the failure, but unfortunately the whole
encoder enable codepath is expected to always succeed.
So for now, catch the enable failure and print an error.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_gem_dma_sync() calls dma_map_page() but does not check the possible
error with dma_mapping_error(). If DMA-API debugging is enabled, the
debug layer will give a warning if dma_mapping_error() has not been
used.
This patch adds proper error handling to omap_gem_dma_sync().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_gem_attach_pages() calls dma_map_page() but does not check the
possible error with dma_mapping_error(). If DMA-API debugging is
enabled, the debug layer will give a warning if dma_mapping_error() has
not been used.
This patch adds proper error handling to omap_gem_attach_pages().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
tpd12s015 HW has LS_OE, CT_CP_HPD and HPD gpios. Out of these gpios,
driver only handled LS_OE as optional. The CT_CP_HPD gpio should also
be treated as optional gpio as it is just a power saving feature. Some
boards hardwire this gpio to be always enable. In this patch, all access
to CT_CP_HPD gpio is made optional.
Signed-off-by: Manisha Agrawal <manisha.agrawal@ti.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
All devices using tpd12s015 driver are doing DT boot. No need of further
supporting the platform data. This patch removes support for platform
data.
Signed-off-by: Manisha Agrawal <manisha.agrawal@ti.com>
[tomi.valkeinen@ti.com: minor adjustments]
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This patch adds wrapper functions for readl() and writel(), dmm_read()
and dmm_write(), so that we can implement workaround for DRA7 errata
i878.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The current driver uses non-blocking DMM fill when releasing memory.
This gives us a small performance increase as we don't have to wait for
the fill operation to finish.
However, the driver does not have any error handling for non-blocking
fill. In case of an error, the fill operation may silently fail, leading
to leaking DMM engines, which may eventually lead to deadlock if we run
out of DMM engines.
This patch makes the DMM driver always use blocking fills, so that we
can catch the errors. A more complex option would be to allow
non-blocking fills, and implement proper error handling, but that is
left for the future.
This patch is a HACK, as the proper fix is to either decide to always
use sync fills and remove all the async related code, or fix the async
code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
We occasionally see DISPC sync-lost errors when enabling and disabling
HDMI. Sometimes we get only a few, which get handled (ignored) by the
driver, but sometimes there's a flood of the errors which doesn't seem
to stop.
The HW team has root caused this to the order in which HDMI and DISPC
are enabled/disabled. Currently we enable HDMI first, and then DISPC,
and vice versa when disabling. HW team's suggestion is to do it the
other way around.
This patch changes the order, but this has two side effects as the pixel
clock is produced by HDMI, and the clock is not running when we
enable/disable DISPC:
* When enabling DISPC first, we don't get vertical sync events
* When disabling DISPC last, we don't get FRAMEDONE event
At the moment we use both of those to verify that DISPC has been
enabled/disabled properly. Thus this patch also needs to change the
omapdrm and omapdss which handle the DISPC side.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The STi drm driver correctly warns about invalid format strings
when built with 64-bit dma_addr_t:
sti_hqvdp.c: In function 'sti_hqvdp_vtg_cb':
sti_hqvdp.c:605:119: warning: format '%x' expects argument of type
'unsigned int', but argument 5 has type 'dma_addr_t {aka long long
unsigned int}' [-Wformat=]
sti_hqvdp.c: In function 'sti_hqvdp_atomic_update':
sti_hqvdp.c:931:118: warning: format '%x' expects argument of type
'unsigned int', but argument 5 has type 'dma_addr_t {aka long long
unsigned int}' [-Wformat=]
This could be changed to using the %pad format string, but that
does not work when printing an rvalue, so instead I'm changing
the type in the sti_hqvdp structure to u32, which is what gets
written into the registers anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vincent Abriou <vincent.abriou@st.com>
Fixes for radeon and amdgpu:
- Fix GPUVM flushing on CI and VI
- Misc DPM and Powerplay fixes
- VCE DPM fixes for CZ/ST
- DP hotplug fix
* 'drm-fixes-4.5' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: return from atombios_dp_get_dpcd only when error
drm/amdgpu/cz: remove commented out call to enable vce pg
drm/amdgpu/powerplay/cz: enable/disable vce dpm independent of vce pg
drm/amdgpu/cz: enable/disable vce dpm even if vce pg is disabled
drm/amdgpu/gfx8: specify which engine to wait before vm flush
drm/amdgpu: apply gfx_v8 fixes to gfx_v7 as well
drm/amd/powerplay: send event to notify powerplay all modules are initialized.
drm/amd/powerplay: export AMD_PP_EVENT_COMPLETE_INIT task to amdgpu.
drm/radeon/pm: update current crtc info after setting the powerstate
drm/amdgpu/pm: update current crtc info after setting the powerstate
VDD regulator input was specified for MSM8916. It turns our that this
regulator is used for the display panels used on MSM8916 platforms, but
not the DSI controller itself. Drop this regulator from the list.
Reported-by: Vinay Simha <vinaysimha@inforcecomputing.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
With the implementation of of_graph parsing, it isn't any longer
necessary for msm_host->device node to be same as dsi->dev.of_node. This
only holds true when the connected device is also a child of the dsi_host.
In the case of external bridge chips belonging to a different control
bus, these are guaranteed to be different.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We have a msm_fbev_free function to uninit fb_helper stuff, but we aren't
using it. Call it in msm_unload.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
attach_dev gets called in mdp4_kms_init, but there is no corresponding
detach_dev called in the error path or in the kms driver unload path.
Detach and destroy mmu in mdp4_destroy.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Assign drm_atomic_helper_crtc_set_property helper to MDP4 and MDP5
crtcs' set_property ops. This replaces the custom funcs that
returned an error even for standard crtc properties.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add support for United Radiant Technology UMSH-8596MD-xT 7.0" WVGA TFT
LCD panels in the simple-panel driver.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The LG lp120up1 TFT LCD panel with eDP interface is a 12.0" 1920x1280
panel, which can be supported by the simple panel driver.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Set hsync/vsync to active low for g121x1_l03 panel to match the
recommended setting in the datasheet.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
MIPI DSI devices are inherently aware of their host because they share a
parent-child hierarchy in the device tree.
Non-DSI drivers that create DSI device don't have this data. In order to
get this information, they require to a phandle to the DSI host in the
device tree.
Maintain a list of all the DSI hosts that are currently registered. This
list will be used to find the struct mipi_dsi_host corresponding to the
device tree node passed to of_find_mipi_dsi_host_by_node().
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A driver calling mipi_dsi_device_register_full() might want to remove
the device once it's done. It might also require it in an error handling
path in case something went wrong.
Create mipi_dsi_device_unregister() for this purpose and use it within
mipi_dsi_remove_device_fn() as it does the same thing.
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In amdgpu_connector_hotplug(), we need to start DP link
training only after we have received DPCD. The function
amdgpu_atombios_dp_get_dpcd() returns non-zero value only
when an error condition is met, otherwise returns zero.
So in case the function encounters an error, we need to
skip rest of the code and return from amdgpu_connector_hotplug()
immediately. Only when we are successfull in reading DPCD
pin, we should carry on with turning-on the monitor.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This code path is not currently enabled now that we properly
respect the vce pg flags, so uncomment the actual pg calls
so the code is as it should be we are eventually able to
enable vce pg.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
with this event, powerplay can adjust current power state if needed.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This is needed to init the dynamic states without a display. To be
used in the next commit.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
On CI, we need to see if the number of crtcs changes to determine
whether or not we need to upload the mclk table again. In practice
we don't currently upload the mclk table again after the initial load.
The only reason you would would be to add new states, e.g., for
arbitrary mclk setting which is not currently supported.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
On CI, we need to see if the number of crtcs changes to determine
whether or not we need to upload the mclk table again. In practice
we don't currently upload the mclk table again after the initial load.
The only reason you would would be to add new states, e.g., for
arbitrary mclk setting which is not currently supported.
Acked-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Add a device name field in struct mipi_dsi_device. This name is not the
same as the device name (which is of the format "hostname.reg"). When
the device is created via DT, this name is set to the modalias string.
In the non-DT case, the driver creating the DSI device provides the
name by populating a field in struct mipi_dsi_device_info.
Matching for DT case would be as it was before. For the non-DT case, we
compare the device and driver names. Other buses (like I2C/SPI) perform
a non-DT match by comparing the device name and entries in the driver's
id_table. Such a mechanism isn't used for the DSI bus.
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use mipi_dsi_device_register_full() for device creation. This takes in
a struct mipi_dsi_device_info as a template to populate the DSI device
information.
The reason to introduce this is to have a way to create DSI devices not
available via DT. Drivers that want to create a DSI device can populate
a struct mipi_dsi_device_info and call this function. For DSI devices
available via DT, of_mipi_dsi_device_add() is used as before, but this
now calls mipi_dsi_device_register_full() internally.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
of_mipi_dsi_device_add() is used only when CONFIG_OF is enabled. It
currently works if OF support is disabled, but this will change when we
add more functionality to it.
Define the original function if CONFIG_OF is enabled and a dummy
function otherwise.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
