The interrupts for EDID_READY or DDC_ERROR were never enabled in this
driver, so reading EDID always timed out when chip was powered down and
interrupts were used. Fix this and also remove clearing the interrupt
flags, they are cleared in POWER_DOWN mode anyhow (unlike the interrupt
enable flags) according to docs and my tests.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Archit Taneja <architt@codeaurora.org>
Unfortunately we don't know all panels and platforms out there and we
found internal prototypes without VBT proper set but where only
link in standby worked well.
So, before enable PSR by default let's instrument the PSR parameter
in a way that we can identify different panels out there that might
require or work better with link standby mode.
It is also useful to say that for backward compatibility I'm not
changing the meaning of this flag. So "0" still means disabled
and "1" means enabled with full support and maximum power savings.
v2: Use positive value instead of negative for different operation mode
as suggested by Daniel.
v3: As Paulo suggested use 2 to force link standby and 3 to force link
fully on. Also split the link_standby introduction in a separated patch.
v4: Use DRM_ERROR for link off request on platforms that don't support and
Remove the quirk promise.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454356928-19779-1-git-send-email-rodrigo.vivi@intel.com
Link standby support has been deprecated with 'commit 89251b177
("drm/i915: PSR: deprecate link_standby support for core platforms.")'
The reason for that is that main link in full off offers more power
savings and on HSW and BDW implementations on source side had known
bugs with link standby.
However that same HSD report only mentions BDW and HSW and tells that
a fix was going to new platforms. Since on Skylake link standby
didn't cause the bad blank flickering screens seen on HSW and BDW
let's respect VBT again for this and future platforms.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Current code not just block link_standby for non DDI platforms but also
block PSR from work on other ports B/C/D/E.
So, besides change any behaviour let's just fix the mess a bit here and
reuse HSW check to block the other ports and reduce the second if only to
link stadnby request.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Commit a9fa852886 ("drm/exynos: dp: add of_graph dt binding support
for panel") made the Exynos DP DT binding more consistent since the OF
graph could be used to lookup either a panel or a bridge device node.
Before that commit, a panel would be looked up using a phandle and a
bridge using the OF graph which made the DT binding not consistent.
But the patch broke the later case since not finding a panel dev node
would cause the driver's to do a probe deferral instead of attempting
to lookup a bridge device node associated with the remote endpoint.
So instead of returning a -EPROBE_DEFER if a panel is not found, check
if there's a bridge and only do a probe deferral if both aren't found.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Michal Suchanek <hramrach@gmail.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The newly added runtime-pm support for exynos-drm encloses the
pm functions in an #ifdef, but not the functions that are called
from them and nowhere else, which produces warnings:
drm/exynos/exynos_drm_dsi.c:733:13: warning: 'exynos_dsi_disable_clock' defined but not used [-Wunused-function]
static void exynos_dsi_disable_clock(struct exynos_dsi *dsi)
^
drm/exynos/exynos_drm_dsi.c:1291:13: warning: 'exynos_dsi_disable_irq' defined but not used [-Wunused-function]
static void exynos_dsi_disable_irq(struct exynos_dsi *dsi)
^
This removes the #ifdef and instead marks the functions as
__maybe_unused, so gcc can silently discard them and all called
functions when CONFIG_PM is disabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The runtime PM operations use the suspend/resume functions
even when CONFIG_PM_SLEEP is not set, but this now fails
for the exynos DRM driver:
exynos_mixer.c:1289:61: error: 'exynos_mixer_resume' undeclared here (not in a function)
SET_RUNTIME_PM_OPS(exynos_mixer_suspend, exynos_mixer_resume, NULL)
This removes the #ifdef and instead marks the functions as
__maybe_unused, which does the right thing in all cases and
also looks nicer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The FBC fixes we've been doing in the last months required a lot of
refactor, so functions that were once big and called from different
spots are now small and called only once. IMHO now it's better to just
move the contents of these functions to their only callers since this
reduces the number of indirections while reading the code.
While at it, also improve the related comments a little bit.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-26-git-send-email-paulo.r.zanoni@intel.com
Our dmesg messages started being misleading after we converted to the
enable+activate model: we always print "Disabling FBC", even when
we're just deactivating it. So, for example, when I boot my machine
and do "dmesg | grep -i fbc", I see:
[drm:intel_fbc_enable] Enabling FBC on pipe A
[drm:set_no_fbc_reason] Disabling FBC: framebuffer not tiled or fenced
but then, if I read the debugfs file, I will see:
$ sudo cat i915_fbc_status
FBC enabled
Compressing: yes
so we can conclude that dmesg is misleading, since FBC is actually
enabled. What happened is that we deactivated FBC due to fbcon not
being tiled, but when we silently reactivated it when the display
manager started. We don't print activation messages since there may be
way too many of these operations per second during normal desktop
usage.
One possible solution would be to change set_no_fbc_reason to
correctly differentiate between disable and deactivation, but we
removed support from printing activation/deactivation messages in the
past because they were too frequent. So instead of doing this, let's
just not print anything on dmesg, and leave the debugfs file if the
user needs to investigate something. We already print when we enable
and disable FBC anyway on a given pipe, so this should already help
triaging bugs.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-22-git-send-email-paulo.r.zanoni@intel.com
Older FBC platforms have this restriction where FBC can't be enabled
if multiple pipes are enabled. In the current code, we disable FBC
before the second pipe becomes visible.
One of the problems with this code is that the current
multiple_pipes_ok() implementation just iterates through all CRTCs
looking at their states, but it doesn't make sure that the state
locks are grabbed. It also can't just grab the locks for every CRTC
since this would kill one of the biggest advantages of atomic
modesetting.
After the recent FBC changes, we now have the appropriate locks for
the given CRTC, so we can just try to maintain the state of each CRTC
and update it once intel_fbc_pre_update is called.
As a last note, I don't have gen 2/3 machines to test this code. My
current plan is to enable FBC on just the newer platforms, so this
patch is just an attempt to get the gen 2/3 code at least looking
sane, so if one day someone decide to fix FBC on these platforms, they
may have less work to do.
Not-tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (only on HSW+)
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-16-git-send-email-paulo.r.zanoni@intel.com
We'll now call intel_fbc_pre_update instead of intel_fbc_deactivate
during atomic commits. This will continue to guarantee that we
deactivate FBC and it will also update the state checking structures
at the correct time. Then, later, at the point where we were calling
intel_fbc_update, we'll only need to call intel_fbc_post_update.
Also add the proper warnings in case we don't have the appropriate
locks. Daniel mentioned the warnings will have to be removed for async
commits, but let's keep them here while we can.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-12-git-send-email-paulo.r.zanoni@intel.com
So now pre_update will be responsible for unconditionally deactivating
FBC and updating the state cache, while post_update will be
responsible for checking if it can be enabled, then enabling it.
This is one more step into proper locking.
Notice that intel_fbc_flush now calls post_update directly. The FBC
flush can only happen for drawing operations - since we explicitly
ignore the flips -, so the FBC state is not expected to have changed
at this point. With this we can just run post_update, which will make
sure we won't deactivate+reactivate FBC as would be the case now if we
called pre_update + post_update.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-11-git-send-email-paulo.r.zanoni@intel.com
Per the new atomic locking rules, we need to cache the CRTC, plane and
FB state structures we use so we can access them later without needing
more locks. So do this.
Notice that there are some pieces of the FBC code that look at things
that are only computed during the modeset, so we can't just can't
precompute whether FBC can be activated during the update_state_cache
stage. We may be able to do this later.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-10-git-send-email-paulo.r.zanoni@intel.com
We unconditionally disable/update FBC even during the page flip
IOCTLs, and an unconditional disable/update at every atomic commit
touching the primary plane shouldn't impact PC state residency
noticeably. Besides, the code that checks for rotation is a good hint
that we may be forgetting something else, so let's leave all the
decisions to intel_fbc.c, making the code much safer.
Once we have the code to properly make FBC enable/update decisions
based on atomic states, with proper locking, then we'll be able to
evaluate whether it will be worth trying to optimize the cases where a
disable isn't needed.
v2: Upstream moved and now our patch needs to remove dev_priv.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453406837-10511-1-git-send-email-paulo.r.zanoni@intel.com
Before this patch, page flips would call intel_frontbuffer_flip() and
intel_frontbuffer_flip_complete(), which would call intel_fbc_flush(),
which would call intel_fbc_update(). The problem is that drawing
operations also trigger intel_fbc_flush() calls, so it's not
guaranteed that we have the CRTC and FB locks grabbed when
intel_fbc_flush() happens, since the call trace may come from the
rendering path.
We're trying to make the FBC code grab the appropriate CRTC/FB locks,
so split the drawing and the flipping logic in order to achieve that
in later patches. So now the frontbuffer tracking code is just going
to be used for frontbuffer drawing, and intel_fbc_update() is going to
be used directly for actual page flips.
As a note, we don't need to call intel_fbc_flip() during the two
places where we call intel_frontbuffer_flip() since in one of them we
already have an intel_fbc_update() call, and in the other we have the
planes disabled.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-7-git-send-email-paulo.r.zanoni@intel.com
We say "dev_priv->fbc.something" way too many times in our code while
we could be saying just "fbc->something" with a previous declaration
of fbc. This has been bothering me for a while but I didn't want to
patch it since I wanted to fix the real problems first. But as I add
more code I keep thinking about it, especially since it makes the code
easier to read and it can make us fit 80 columns easier, so let's just
do the change now.
While at it, also rename from i915_fbc to intel_fbc because the whole
FBC code uses intel_fbc.
v2: Rebase after the work_fn changes.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453406763-10400-1-git-send-email-paulo.r.zanoni@intel.com
The early return inside __intel_fbc_update does not completely check
all the parameters that affect the FBC register values. For example,
we currently lack looking at crtc->adjusted_y (for the fence Y offset)
and all the parameters that affect the CFB size (for i8xx).
Instead of just adding the missing parameters to the check and hoping
that any changes to the fbc_activate functions also come with a
matching change to the __intel_fbc_update check, introduce a new
structure where we store these parameters and use the structure at the
fbc_activate function. Of course, it's still possible to access
everything from dev_priv in those functions, but IMHO the new code
will be harder to break.
v2: Rebase.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-5-git-send-email-paulo.r.zanoni@intel.com
Instead of waiting for 50ms, just wait until the next vblank, since
it's the minimum requirement. The whole infrastructure of FBC is based
on vblanks, so waiting for X vblanks instead of X milliseconds sounds
like the correct way to go. Besides, 50ms may be less than a vblank on
super slow modes that may or may not exist.
There are some small improvements in PC state residency (due to the
fact that we're now using 16ms for the common modes instead of 50ms),
but the biggest advantage is still the correctness of being
vblank-based instead of time-based.
v2:
- Rebase after changing the patch order.
- Update the commit message.
v3:
- Fix bogus vblank_get() instead of vblank_count() (Ville).
- Don't forget to call drm_crtc_vblank_{get,put} (Chris, Ville)
- Adjust the performance details on the commit message.
v4:
- Don't grab the FBC mutex just to grab the vblank (Maarten)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453406585-10233-1-git-send-email-paulo.r.zanoni@intel.com
Here are some fixes for drm/rockchip, these fixes base on drm-next.
These fixes works on my popmetal(rk3288) board.
About patch: drm/atomic-helper: Export framebuffer_changed()
Daniel Vetter ack for merging it through rockchip git trees, so framebuffer_changed() can be reused by drm/rockchip.
All others looks good, so I'd like you can land them.
* 'drm-rockchip-next-fixes-2016-01-22' of https://github.com/markyzq/kernel-drm-rockchip:
drm/rockchip: respect CONFIG_DRM_FBDEV_EMULATION
drm/rockchip: fix wrong pitch/size using on gem
drm/rockchip: explain why we can't wait_for_vblanks
drm/rockchip: don't wait for vblank if fb hasn't changed
drm/atomic-helper: Export framebuffer_changed()
drm/rockchip/dsi: fix handling mipi_dsi_pixel_format_to_bpp result
drm/rockchip: vop: fix mask when updating interrupts
drm/rockchip: cleanup unnecessary export symbol
drm/rockchip: Don't build rockchip_drm_vop as modules
