Felipe writes:
USB changes for v4.21
So it looks like folks are interested in dwc3 again. Almost 64% of the
changes are in dwc3 this time around with some other bits in gadget
functions and dwc2.
There are two important parts here: a. removal of the waitqueue from
dwc3's dequeue implementation, which will guarantee that gadget
functions can dequeue from any context and; b. better method for
starting isochronous transfers to avoid, as much as possible, missed
isoc frames.
Apart from these, we have the usual set of non-critical fixes and new
features all over the place.
* tag 'usb-for-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (56 commits)
usb: dwc2: Fix disable all EP's on disconnect
usb: dwc3: gadget: Disable CSP for stream OUT ep
usb: dwc2: disable power_down on Amlogic devices
Revert "usb: dwc3: pci: Use devm functions to get the phy GPIOs"
USB: gadget: udc: s3c2410_udc: convert to DEFINE_SHOW_ATTRIBUTE
usb: mtu3: fix dbginfo in qmu_tx_zlp_error_handler
usb: dwc3: trace: add missing break statement to make compiler happy
usb: dwc3: gadget: Report isoc transfer frame number
usb: gadget: Introduce frame_number to usb_request
usb: renesas_usbhs: Use SIMPLE_DEV_PM_OPS macro
usb: renesas_usbhs: Remove dummy runtime PM callbacks
usb: dwc2: host: use hrtimer for NAK retries
usb: mtu3: clear SOFTCONN when clear USB3_EN if work as HS mode
usb: mtu3: enable SETUPENDISR interrupt
usb: mtu3: fix the issue about SetFeature(U1/U2_Enable)
usb: mtu3: enable hardware remote wakeup from L1 automatically
usb: mtu3: remove QMU checksum
usb/mtu3: power down device ip at setup
usb: dwc2: Disable power down feature on Samsung SoCs
usb: dwc3: Correct the logic for checking TRB full in __dwc3_prepare_one_trb()
...
Kishon writes:
phy: for 4.21
*) Change phy set_mode ops to take both mode and setmode as arguments
*) Add phy_configure() and phy_validate() API's mostly used for MIPI D-PHY
*) Add helpers to get default values of parameters define in MIPI D-PHY spec
*) Add driver for TI's CPSW Port PHY Interface Mode selection
*) Add driver for Cadence Sierra PHY used with USB and PCIe
*) Add driver for Freescale i.MX8MQ USB3 PHY
*) Fixes QMP PHY bindings to allow the clocks provided by the PHY to be
pointed at in device tree
*) Fix for using fully specified regions (in device tree) for configuring
the second lane in dual lane PHYs in QMP PHY
*) Add support for Allwinner H6 USB2 PHY in phy-sun4i-usb driver
*) Update phy-rcar-gen3-usb driver to follow the hardware manual
*) Add support for fine grained power management in mapphone-mdm6600 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-4.21_v1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (30 commits)
phy: qcom-qmp: Expose provided clocks to DT
dt-bindings: phy-qcom-qmp: Move #clock-cells to child
phy: qcom-qmp: Utilize fully-specified DT registers
dt-bindings: phy-qcom-qmp: Fix register underspecification
phy: ti: fix semicolon.cocci warnings
phy: dphy: Add configuration helpers
phy: Add MIPI D-PHY configuration options
phy: Add configuration interface
phy: Add MIPI D-PHY mode
phy: add driver for Freescale i.MX8MQ USB3 PHY
dt-bindings: phy: add binding for Freescale i.MX8MQ USB3 PHY
phy: Use of_node_name_eq for node name comparisons
net: ethernet: ti: cpsw: add support for port interface mode selection phy
dt-bindings: net: ti: cpsw: switch to use phy-gmii-sel phy
phy: ti: introduce phy-gmii-sel driver
dt-bindings: phy: add cpsw port interface mode selection phy bindings
phy: mvebu-cp110-comphy: fix spelling in structure name
phy: mapphone-mdm6600: Improve phy related runtime PM calls
phy: renesas: rcar-gen3-usb2: follow the hardware manual procedure
phy: cadence: Add driver for Sierra PHY
...
The phy-qcom-qmp bindings specified #clock-cells as 1. This was never used
because of_clk_add_provider() was never called, so there was no way anybody
could reference these clocks from DT. Furthermore, even if they could be
accessed, the bindings never specified what should go in that additional
cell.
Fix these incomplete and broken bindings. Move the #clock-cells into the
child node, since that is the actual clock provider, and not all
instances of qcom-qmp-phy are clock providers. Also set #clock-cells to
zero, since there's nothing to pass to it.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add register regions for the second lane of dual-lane nodes.
This additional specification is needed so that the driver can stop
reaching beyond the tx and rx register allocations to get at the
second lane registers in a dual-lane PHY.
While in there, document #clock-cells as optional for PHYs that don't
provide a pipe clock. Also, document the pcs_misc register region, which
was being quietly supplied and used.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds the binding for the USB3 PHY found on the i.MX8M SoC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The cpsw-phy-sel driver was replaced with new PHY driver phy-gmii-sel, so
deprecate cpsw-phy-sel bindings and update CPSW binding to use phy-gmii-sel
PHY bindings.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add DT binding documentation for Sierra PHY. The PHY supports
a number of different protocols, including PCIe and USB.
The PHY lanes may be configured as single or multi-lane links.
Each link is treated as a separate sub-node. For example, if
there are 4 lanes in total the first 2 might be configured as
a multi-lane PCIe link while the other two are single lane
USB links, and in this case there would be 3 sub-nodes.
There are two resets for the PHY block (one for APB register
access, one for the PHY link) and separate resets for each
link. For multi-lane links, the reset corresponds to the
reset line on the master lane, the resets on other lanes
have no effect.
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The USB2.0 PHY on Allwinner H6 is similar to the ones on the ones on
older SoCs, but with holes in PHY number (USB1 and USB2 are missing, in
which USB1 is a USB3 PHY).
Add binding for the PHY.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The "at," prefix was never correct for Atmel, so fix the few occurrences
that got it wrong. Use "atmel," instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Acked-by: Peter Rosin <peda@axentia.se>
[wsa: merged two patches into one, dropped 'trivial-devices' hunk which
needs to go in seperately]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the internal timer peripheral on RV1108.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Document the new amd,imageon compatible, used for non-qcom hardware that
uses the drm/msm driver (iMX5).
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This allows controlling which of the 8 lanes are used for 6 bit color.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
dt-bindings: Changes for v4.21-rc1
This contains a few cleanups of and additions to existing device tree
bindings, such as XUSB, EMC, PMC and thermal.
* tag 'tegra-for-4.21-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: tegra186-pmc: Add interrupt controller properties
dt-bindings: thermal: tegra-bpmp: Add Tegra194 support
dt: bindings: Move tegra20-emc binding to memory-controllers directory
dt: bindings: tegra20-emc: Document clock property
dt: bindings: tegra20-emc: Document interrupt property
dt-bindings: usb: xhci-tegra: Add power-domain details
Signed-off-by: Olof Johansson <olof@lixom.net>
Renesas ARM Based SoC DT Bindings Updates for v4.21
* Move 'renesas,prr' binding to its own document
- Prepration for converting board-level bindings to json-schema
* Document iW-RainboW-G20D-Qseven-RZG1N board and iWave RZ/G1N SOM
* tag 'renesas-dt-bindings-for-v4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
dt-bindings: arm: renesas: Move 'renesas,prr' binding to its own doc
dt-bindings: arm: renesas: Document iW-RainboW-G20D-Qseven-RZG1N board
dt-bindings: arm: renesas: Document iWave RZ/G1N SOM
Signed-off-by: Olof Johansson <olof@lixom.net>
The status quo on i.MX6 is that if "over-current-active-high" is
specified in the device tree this is configured as expected. If
the property is missing polarity isn't changed and so the
polarity is kept as setup by the bootloader. Reset default is
active high, so active low can only be used with help by the
bootloader. On i.MX7 it is similar, but there disabling of
over current detection has a similar inconsistency.
This patch introduces a new property that allows to explicitly
configure for active low over current detection and consistently
sets this up. In the absence of an explicit configuration the
bit is kept as is. On i.MX7 over current detection is used unless
disabled in the device tree.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
For USB HSIC, the data and strobe pin needs to be pulled down
at default, we consider it as "idle" state. When the USB host
is ready to be used, the strobe pin needs to be pulled up,
we consider it as "active" state.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The pcf85263 RTC is compatible with the pcf85363 RTC.
The difference between the pcf85263 and pcf85363 RTC is that the latter has
64 bytes more RAM. This renders them incompatible from a DT point of view.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The example should follow the practice or using a generic node name
instead of the precise programming model, as recommended by the DTSpec.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When specifying external clock inputs to the CCM the current code
requires the clocks to be in a "clocks" child node of the DT root.
This is not really conformant with DT best practices.
To avoid the need to deviate from those best practices, allow the
clock inputs to be specified via standard clock handles. This is
in line with how drivers of the later CCM driver revisions on
newer i.MX SoCs handle this.
As we can't retroactively change the DT binding, allow this as an
option with a fallback to the old way of how this has been handled.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add new compatible to the device tree bindings.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Several conflicts, seemingly all over the place.
I used Stephen Rothwell's sample resolutions for many of these, if not
just to double check my own work, so definitely the credit largely
goes to him.
The NFP conflict consisted of a bug fix (moving operations
past the rhashtable operation) while chaning the initial
argument in the function call in the moved code.
The net/dsa/master.c conflict had to do with a bug fix intermixing of
making dsa_master_set_mtu() static with the fixing of the tagging
attribute location.
cls_flower had a conflict because the dup reject fix from Or
overlapped with the addition of port range classifiction.
__set_phy_supported()'s conflict was relatively easy to resolve
because Andrew fixed it in both trees, so it was just a matter
of taking the net-next copy. Or at least I think it was :-)
Joe Stringer's fix to the handling of netns id 0 in bpf_sk_lookup()
intermixed with changes on how the sdif and caller_net are calculated
in these code paths in net-next.
The remaining BPF conflicts were largely about the addition of the
__bpf_md_ptr stuff in 'net' overlapping with adjustments and additions
to the relevant data structure where the MD pointer macros are used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Removed the compatible string "snps,dw-pcie", it is for the reference
platform driver for PCI RC IP Protoyping Kits based on the ARC SDP,
so it is not suitable for all platform with designware PCIe controller,
and platform vendors have themselves' drivers.
The compatible string "snsp,dw-pcie" was added by mistake and it's not
matched that time, but it is matched because PCIe drivers has been
collected recently.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull clk fixes from Stephen Boyd:
"A few clk driver fixes this time:
- Introduce protected-clock DT binding to fix breakage on qcom
sdm845-mtp boards where the qspi clks introduced this merge window
cause the firmware on those boards to take down the system if we
try to read the clk registers
- Fix a couple off-by-one errors found by Dan Carpenter
- Handle failure in zynq fixed factor clk driver to avoid using
uninitialized data"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: zynqmp: Off by one in zynqmp_is_valid_clock()
clk: mmp: Off by one in mmp_clk_add()
clk: mvebu: Off by one bugs in cp110_of_clk_get()
arm64: dts: qcom: sdm845-mtp: Mark protected gcc clocks
clk: qcom: Support 'protected-clocks' property
dt-bindings: clk: Introduce 'protected-clocks' property
clk: zynqmp: handle fixed factor param query error
The example should follow the practice or using a generic node name
instead of the precise programming model, as recommended by the DTSpec.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
From LPC18xx and LPC43xx User Manuals the GPIO controller consists of
the following weakly connected blocks:
* GPIO pin interrupt block at 0x40087000,
* GPIO GROUP0 interrupt block at 0x40088000,
* GPIO GROUP1 interrupt block at 0x40089000,
* GPIO port block at 0x400F4000.
While all 4 sub-controller blocks have their own I/O addresses, moreover
all 3 interrupt blocks are APB0 peripherals and high-speed GPIO block is
an AHB slave, according to the hardware manual interrupt controllers and
GPIO controller block are seen as a single device, all 4 sub-controllers
have the shared reset signal RGU #28 and the same shared clock to access
registers CLK_Mx_GPIO on CCU1.
The change adds descriptions of the currently missing interrupt controller
blocks found on GPIO controller, new added properties are 'reg-names',
'resets', 'interrupt-controller' and '#interrupt-cells', also the example
is updated to reflect the changes in device tree binding description.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The register range for the RTC extends beyond 0x54.
Use the size from the user manual's memory map instead.
Fixes: 9765d2d943 ("rtc: sun6i: Add sun6i RTC driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Update the PSPI NPCM binding document of the spi aliases use
to define the spi ID number.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Bindings should use 'reset-gpios', not 'reset-gpio'. The driver needs to
switch to the gpiod consume API to handle this correctly.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Bindings should use 'reset-gpios', not 'reset-gpio'. The driver needs to
switch to the gpiod consume API to handle this correctly.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
