Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An incorrect value of use_fwsup is set for 4-way handshake offload for
WPA//WPA2-PSK, caused by commit 3b1e0a7bdf ("brcmfmac: add support for
SAE authentication offload"). It results in missing bit
BRCMF_VIF_STATUS_EAP_SUCCESS set in brcmf_is_linkup() and causes the
failure. This patch correct the value for the case.
Also setting bit BRCMF_VIF_STATUS_EAP_SUCCESS for SAE offload case in
brcmf_is_linkup() to fix SAE offload failure.
Fixes: 3b1e0a7bdf ("brcmfmac: add support for SAE authentication offload")
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1589277788-119966-1-git-send-email-chi-hsien.lin@cypress.com
In WLAN, priority among various access categories of traffic is
always set by the AP using WMM parameters and this may not always
follow the standard 802.1d priority.
In this change, priority is adjusted based on the AP WMM params
received as part of the Assoc Response and the same is later used
to map the priority of all incoming traffic.
In a specific scenario where EDCA parameters are configured to be same
for all ACs, use the default FW priority definition to avoid queuing
packets of all ACs to the same priority queue.
This change fixes the following 802.11 certification tests:
* 11n - 5.2.31 ACM Bit Conformance test
* 11n - 5.2.32 AC Parameter Modification test
* 11ac - 5.2.33 TXOP Limit test
Signed-off-by: Saravanan Shanmugham <saravanan.shanmugham@cypress.com>
Signed-off-by: Justin Li <justin.li@cypress.com>
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588661487-21884-2-git-send-email-chi-hsien.lin@cypress.com
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Report monitor interface availability using cfg80211 and support it in
the add_virtual_intf() and del_virtual_intf() callbacks. This new
feature is conditional and depends on firmware flagging monitor packets.
Receiving monitor frames is already handled by the brcmf_netif_mon_rx().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move similar/duplicated code out of combination specific code blocks.
This simplifies code a bit and allows adding more combinations later.
A list of combinations remains unchanged.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With RSDB mode, FMAC and firmware are able to create 2 or more AP,
so we should not set mbss in vif structure if firmware does not
support MBSS feature.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With firmware RSDB feature
1. The maximum support interface is four.
2. The maximum difference channel is two.
3. The maximum interfaces of {station/p2p client/AP} are two.
4. The maximum interface of p2p device is one.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
4359 dongles do not support setting roaming parameters (error -52).
Do not fail the 80211 configuration in this case.
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware may have SAE authentication code built-in. This is
detected by the driver and indicated in the wiphy features flags.
User-space can use this flag to determine whether or not to provide
the password material for SAE authentication in the nl80211 CONNECT
command.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With FT-802.1X, driver should send a port authorized event right after
sending a roamed event. It is used to indicate that a new AP is already
authorized so 802.1X is not required.
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This moves "ops" pointer from "struct brcmf_cfg80211_info" to the
"struct brcmf_pub". This movement makes it possible to allocate wiphy
without attaching cfg80211 (brcmf_cfg80211_attach()). It's required for
later separation of wiphy allocation and driver initialization.
While at it fix also an unlikely memory leak in the brcmf_attach().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The strncpy() may truncate the copied string,
replace it by the safer strscpy().
To avoid below compile warning with gcc 8.2:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:In function 'brcmf_vndr_ie':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:4227:2:
warning: 'strncpy' output truncated before terminating nul copying 3 bytes from a string of the same length [-Wstringop-truncation]
strncpy(iebuf, add_del_cmd, VNDR_IE_CMD_LEN - 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Xulin Sun <xulin.sun@windriver.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c: In function brcmf_update_bss_info:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:2962:5: warning: variable dtim_period set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c: In function brcmf_update_bss_info:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:2961:6: warning: variable beacon_interval set but not used [-Wunused-but-set-variable]
They are never used so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver has custom regulatory rules which had maximum bandwidth
for 5GHz channels set to 80MHz. As a consequence the driver can
not use 160MHz in AP mode even when the device supports it. So
relax the rules allowing 160MHz. After wiphy_register() the channel
flags are updated according what the device actually supports.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case kmemdup fails, the fix sets conn_info->req_ie_len and
conn_info->resp_ie_len to zero to avoid buffer overflows.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This macro will be used in more places not just the cfg80211.c. It makes
sense to pass some common struct to it as "struct wiphy" is mostly
referenced in cfg80211 code only.
A very common one (used above the bus abstraction layer) is struct
brcmf_pub. Many functions already keep reference to it which will make
using bphy_err() simpler. It should also allow extending that macro's
logic if it's ever needed.
This improves code recently added in the commit 3ef005b82e ("brcmfmac:
add bphy_err() and use it in the cfg80211.c").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far 160 MHz channels were treated as 20 MHz ones which was breaking
support for 40/80 MHz due to the brcmf_construct_chaninfo() logic and
its assumptions.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
1) Use switch to simplify/improve the code & avoid some duplication
2) Add warning for unsupported values
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This new macro uses wiphy_err() which:
1) Should be the best choice with wiphy already created
2) Uses dev_err() which allows identifying error-affected device
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit 1204aa17f3 ("brcmfmac: set WIPHY_FLAG_HAVE_AP_SME flag")
the Raspberry Pi 3 A+ (BCM43455) isn't able to operate in AP mode with
hostapd (device_ap_sme=1 use_monitor=0):
brcmfmac: brcmf_cfg80211_stop_ap: setting AP mode failed -52
So add the missing mgmt_stypes for AP mode to fix this.
Fixes: 1204aa17f3 ("brcmfmac: set WIPHY_FLAG_HAVE_AP_SME flag")
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the update_connect_param callback is set, nl80211 expects the flag
WIPHY_FLAG_SUPPORTS_FW_ROAM to be set as well. However, this flag is
only set when modparam roamoff=0, while the callback is set
unconditionally. Since commit 7f9a3e150e this causes a warning in
wiphy_register, which breaks brcmfmac.
Disable the update_connect_param callback when roamoff=0 to fix this.
Fixes: 7f9a3e150e ("nl80211: Update ERP info using NL80211_CMD_UPDATE_CONNECT_PARAMS")
Cc: Stable <stable@vger.kernel.org> # 4.19+
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The frameburst feature can enable per-packet framebursting in firmware
side and get higher TX throughput in High Throughput(HT) mode. To enhance
TX throughput, we enable frameburst mode in default firmware setting.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver can report IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ so it's
important to provide valid & complete info about supported bands for
each channel. By default no support for 160 MHz should be assumed unless
firmware reports it for a given channel later.
This fixes info passed to the userspace. Without that change userspace
could try to use invalid channel and fail to start an interface.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The kernel BUG happens when wowl is enabled from firmware. In
brcmf_wiphy_wowl_params(), cfg is a NULL pointer because it is
drvr->config returned from wiphy_to_cfg(), and drvr->config is not set
yet. To fix it, set drvr->config before brcmf_setup_wiphy() which
calls brcmf_wiphy_wowl_params().
Fixes: 856d5a011c ("brcmfmac: allocate struct brcmf_pub instance using wiphy_new()")
Signed-off-by: Winnie Chang <winnie.chang@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BIT macro uses unsigned long which some architectures handle as 32 bit
and therefore might cause macro's shift to overflow when used on a value
equals or larger than 32 (NL80211_STA_INFO_RX_DURATION and afterwards).
Since 'filled' member in station_info changed to u64, BIT_ULL macro
should be used with all NL80211_STA_INFO_* attribute types instead of BIT
to prevent future possible bugs when one will use BIT macro for higher
attributes by mistake.
This commit cleans up all usages of BIT macro with the above field
in wireless-drivers by changing it to BIT_ULL instead. In addition, there are
some places which don't use BIT nor BIT_ULL macros so align those as well.
Signed-off-by: Omer Efrat <omer.efrat@tandemg.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove and coalesce formats when there is an unnecessary
character after a logging newline. These extra characters
cause logging defects.
Miscellanea:
o Coalesce formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
brcmfmac is a FullMAC driver and it implements/uses cfg80211 interface
for stations management. At the same time it doesn't receive or pass up
management frames.
This flag indicates that authenticator doesn't have to subscribe to or
handle management frames. Some authenticators (e.g. hostapd) were
working with brcmfmac thanks to some extra assumptions. This commit
clears up the situation.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the addition of the TXQ stats to cfg80211, the station_info struct
has grown to be quite large, which results in warnings when allocated on
the stack. Fix the affected places to do dynamic allocations instead.
Fixes: 52539ca89f ("cfg80211: Expose TXQ stats and parameters to userspace")
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The enum nl80211_band used to retrieve wiphy->bands is the same as
wiphy->bands->band which is checked by wiphy_register(). So it can be used
directly as parameter of ieee80211_channel_to_frequency().
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rework the driver so the wiphy instance holds the main driver information
in its private buffer. Previously it held struct brcmf_cfg80211_info
instance so a bit of reorg was needed. This was done so that the wiphy
name or its parent device can be shown in debug output.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The commit "regulatory: add NUL to request alpha2" increases the length of
alpha2 to 3. This causes a regression on brcmfmac, because
brcmf_cfg80211_reg_notifier() expect valid ISO3166 codes in the complete
array. So fix this accordingly.
Fixes: 657308f73e ("regulatory: add NUL to request alpha2")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
