[why]
The mux to switch between refclk and dto_dsc_clk is non double buffered.
However dto dsc clk's phase and modulo divider registers are currently
configured as double buffered update. This causes a problem when we switch to
use dto dsc clk and program phase and modulo in the same sequence. In this
sequence dsc clk is switched to dto but the clock divider programming doesn't
take effect until next frame. When we try to program DSCC registers, SMN bus
will hang because dto dsc clk divider phase is set to 0.
[how]
Configure phase and modulo to take effect immediately. Always switch to dto dsc
clk before DSC clock is unagted. Switch back to refclk after DSC clock is gated.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Function was used to check the number of FEs connected to the current BE.
This was then used to determine if the symclk could be disabled, if all
FEs were disconnected. However, the function would skip over the primary
FE and return 0 when the primary FE was still connected. This caused black
screens on driver disable with an MST daisy chain hooked up.
[HOW]
Refactored the function to correctly return the number of FEs connected to
the input BE. Also renamed it for clarity.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Relja Vojvodic <relja.vojvodic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
fe_clk_en and be_clk_sel have size of 4 but sizeof(fe_clk_en) has
byte size 16 which is lager than the array size.
[HOW]
Use ARRAY_SIZE for calculating size.
This fixes 2 OVERRUN issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Reference clock, either DPREFCLK or DTBCLK can be a value of 0
which then will encounter division by 0.
[How]
Avoid further calculation and programming if refclk is not
populated.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Vbios & Driver have difference pixel rate div policy.
When enabling fast boot & performing blank & unblank w/o timing setting,
pixel clock & pixel rate dividor are not match.
It would cause too high pixel reate and eDP would be black screen.
[How]
We would keep pixel rate div setting by Vbios until next timing setting.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: yi-lchen <yi-lchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
