[WHY]
Previous multi-display HPO fix moved where HPO I/O enable/disable is performed.
The codepath now taken to enable/disable HPO I/O is not used for compliance
test automation, meaning that if a compliance box being driven at a DP1 rate
requests retrain at UHBR, HPO I/O will remain off if it was previously off.
[HOW]
Explicitly update HPO I/O after allocating encoders for test request.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some interface functions are defined in both the public and private HWSS
interfaces, which can lead to confusion and runtime issues, therefore
the duplicates should be eliminated.
[How]
- power_down should only be private, because it's only used within HWSS.
- update_plane_addr should only be public, as it's used outside HWSS.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We resync the FIFO after each pipe update in apply_ctx_to_hw.
However, this means that some pipes (in hardware) are based on the
new context and some are based on the current_state (since the pipes
are updated on at a time). In this case we must ensure to use the
pipe_ctx that's currently still configured in hardware when turning
off / on OTG's and reconfiguring ODM during the resync.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Vbios & Driver have difference pixel rate div policy.
When enabling fast boot & performing blank & unblank w/o timing setting,
pixel clock & pixel rate dividor are not match.
It would cause too high pixel reate and eDP would be black screen.
[How]
We would keep pixel rate div setting by Vbios until next timing setting.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: yi-lchen <yi-lchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently 3-tap chroma subsampling is used for YCbCr422/420. When ODM
pipesplit is used, pixels on the left edge of ODM slices need one extra
pixel from the right edge of the previous slice to calculate the correct
chroma value.
Without this change, the chroma value is slightly different than
expected. This is usually imperceptible visually, but it impacts test
pattern CRCs for compliance test automation.
[HOW]
Update logic to use the register for adding extra left edge pixel for
YCbCr422/420 ODM cases.
Reviewed-by: George Shen <george.shen@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Input mode for the DIG FIFO should be programmed as part of stream
encoder setup.
[HOW]
Pre-calculate the pixels per cycle as part of the pixel clock params,
and program as part of stream encoder setup.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
VBios & Driver may have differnet pixel rate div policy.
If the policy is not same and fast boot is enabled,
it would cause the pixel rate is too high
after driver only performs stream blank & unblank.
[how]
We would keep pixel rate div setting by VBios until next mode set.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Webb Chen <yi-lchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Rename hw_sequencer to hwseq.
Move all hwseq files to unique
folder hwss.
[how]
creating hwss repo in dc, and moved the dcnxx_hwseq.c
and .h files into corresponding new folders inside the hwss
and cleared the linkage errors by adding relative paths
in the Makefile.template.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Mounika Adhuri <moadhuri@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
