[WHY]
Underflow occurs on some platforms when urgent BW is close to
the maximum in DPM0.
[HOW]
It does not occur at DPM1, so as a workaround restrict the maximum
amount and increase the lowest state index for clock states until
we're out of DPM0.
Adds DML2 config options to specify this pe platform as required.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Sung-huai Wang <danny.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On hotpluggin a 4k144 HDMI FRL setup, display fails FRL link training
and falls back to TMDS which is caused by driver not ungating HPO before
doing FRL link training.
[HOW]
Enable debug flag to disable HPO power gate in DCN35
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMCUB can intermittently take longer than expected to process commands.
Old ASIC policy was to continue while logging a diagnostic error - which
works fine for ASIC without IPS, but with IPS this could lead to a race
condition where we attempt to access DCN state while it's inaccessible,
leading to a system hang when the NIU port is not disabled or register
accesses that timeout and the display configuration in an undefined
state.
[How]
We need to investigate why these accesses take longer than expected, but
for now we should disable the timeout on DCN35 to avoid this race
condition. Since the waits happen only at lower interrupt levels the
risk of taking too long at higher IRQ and causing a system watchdog
timeout are minimal.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Future implementations will require a distinction between AC power and
DC power (wall power and battery power, respectively). To accomplish this,
adding a power mode parameter to certain dc interfaces, and adding a
separate DML2 instance for DC mode validation. Default behaviour unchanged.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the DML2 wrapper explicitly accesses context->dml2, that creates a
dependency on where dc saves the DML object. This dependency makes it
harder to have multiple co-existing DML objects, which we would like to
have for upcoming functionality.
[How]
- make all DML21 interfaces take in a DML2 object as parameter
- remove all references to context->dml2, use parameter instead
Reviewed-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The threshold is no longer useful for blocking suboptimal power states
for DCN35 based on real measurement.
[How]
Reduce to the minimum threshold duration, 1us.
Reviewed-by: Gabe Teeger <gabe.teeger@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It was previously disabled for stability purposes, but command
submission causes residency issues in IPS video playback.
[How]
Enable the disallow/reallow pattern back. There's additional checks
now in DMCUB that should make this safer stability wise.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want to support low hz case, but the original
vtotal/vtotal_min/vtotal_max can't support more
than 0x7FFF.
[HOW]
We use the 2 HW reg to contorl long vblank case.
1. OTG_V_COUNT_STOP_CONTROL -> vcount_stop
2. OTG_V_COUNT_STOP_CONTROL2 -> vcount_stop_timer
vcount_stop define from which line we stop using vcount
and start using vcount2.
vcount_stop_timer define how long we use vcount2.
Ex:
Vtotal = 7
OTG_V_COUNT_STOP_CONTROL = 4
OTG_V_COUNT_STOP_CONTROL2 = 5
time : 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11
vcount : 0, 1, 2, 3, - - - - - 4, 5, 6
vcount2 : 0, 1, 2, 3, 4,
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: ChunTao Tso <chuntao.tso@amd.com>
Signed-off-by: Robin Chen<robin.chen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
sw has most of the fgcg enabled which is the same as HW default.
but driver disabled some due to enable flag not initialized.
comparing HW state, we still need to enable dpp and dio.
Reviewed-by: Muhammad Ahmed <ahmed.ahmed@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Workaroud for a race condition where DMCUB is in the process of
committing to IPS1 during the handshake causing us to miss the
transition into IPS2 and touch the INBOX1 RPTR causing a HW hang.
[How]
Disable the reallow to ensure that we have enough of a gap between entry
and exit and we're not seeing back-to-back wake_and_executes.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
the original wait for 2 static frames before enter static screen
was not good enough for IPS-enabled case since enter/exit takes more time.
[How]
Changed logic for hardcoded wait frame values.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Allen Pan <allen.pan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Part of the dc_state interface that deals with adding streams and planes should
remain public, while others that deal with internal status' and subvp should be
private to DC.
[HOW?]
Move and rename the public functions to dc_state.h and private functions to
dc_state_priv.h. Also add some additional functions for extracting subvp meta
data from the state.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML2 means that the dcn3x policy for calculating z-state support
no longer runs from validate_bandwidth.
This means we are unconditionally allowing Z8, the hardware default.
[How]
Port the policy over to DCN35, but with a few modifications:
- Don't use min_dst_y_next_start as a check for Z8/Z10 allow
- Add support for overriding the Z10 stutter period per ASIC
- Cleanup the code to make the policy assignment more clear
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Move all resource files to unique folder resource.
[HOW]
Created resource folder in dc, moved the
dcnxx_resource.c and dcnxx_resource.h files into
corresponding new folders inside the resource and
made appropriate changes for compilation in Makefiles.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mounika Adhuri <moadhuri@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
