This version brings along following fixes:
- Fix underflow issue on 175hz timing
- Add interface to modify DMUB panel power options
- Remove check for default eDP panel_mode
- Add new sequence for 4-lane HBR3 on vendor specific retimers
- Update DPG test pattern programming
- Correct unit conversion for vstartup
- Exit idle optimizations before attempt to access PHY
- Refactor recout calculation with a more generic formula
- Read down-spread percentage from lut to adjust dprefclk.
- Don't apply FIFO resync W/A if rdivider = 0
- Prevent invalid pipe connections
- Rearrange dmub_cmd defs order
- Add VESA SCR case for default aux backlight
- Guard DCN31 PHYD32CLK logic against chip family
- Correct grammar mistakes
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some vendor specific retimer setups for downstream 4-lane HBR3
configuration, the sink will show severe corruption (horizontal shifting)
and intermittent blanking.
[How]
Add new retimer programming sequence before clock recovery when 4 lanes
are active.
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Last ODM slice could be slightly larger than other slice because it can be
including the residual.
[How]
Update DPG pattern programming sequence to use a different width for
last odm slice.
Reviewed-by: Chris Park <chris.park@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
vstartup is calculated to be a large number. It works because
it is within vertical blank, but it reduces region of blank that
can be used for power gating.
[How]
Calculation needs to convert micro seconds to number of
vertical lines.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Reza Amini <reza.amini@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current recout calculation has a few assumptions and implementation
for MPO + ODM combine calculation is very specific. The equation has
too many cases without enough comments to document the detail.
[How]
The change remove the following assumptions:
1. When MPO is enabled, we only allow ODM Combine 2:1
2. ODM Combine always has even segment width.
3. Secondary MPO plane's pipe_ctx copies pre_odm_pipe from
its top pipe.
The change applies a generic formula with more details in comment to
document this solution so it is eaiser to learn and debug later.
Reviewed-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
It is not valid to set the WDIVIDER value to 0, so do not
re-write to DISPCLK_WDIVIDER if the current value is 0
(i.e., it is at it's initial value and we have not made any
requests to change DISPCLK yet).
Reviewed-by: Saaem Rizvi <syedsaaem.rizvi@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Prevent ODM pipe connections between pipes that are not part
of the same plane when adding a plane to context
- Re-attach child pipes of ODM slice about to be disconnected
to prevent any lost pipes with invalid tops/bottoms
- We cannot split if head_pipe is not in ODM. Preventing this
avoids creating an invalid context with an invalid pipe.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ethan Bitnun <ethan.bitnun@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Update 128b/132b downspread factor to 0.3%
- Add helpers to get DMUB FW boot options
- Initialize necessary uninitialized variables
- Add stream overhead in BW calculations for 128b/132b
- Add link encoding to timing BW calculation parameters
- Prevent vtotal from being set to 0
- Fix race condition when turning off an output alone
- Keep PHY active for DP displays on DCN31
- Fix ASIC check in aux timeout workaround
- ABM pause toggle
- Add missing triggers for full updates
- Disable MPC split by default on special asic
- Add additional refresh rate conditions for SubVP cases
- Fix DP2 link training failure with RCO
- Reenable all root clock gating options
- Cache backlight_millinits in link structure and setting brightness accordingly
- Refine to decide the verified link setting
- Update SW cursor fallback for subvp high refresh
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Full update was missed for the following cases:
- Idle optimization is enabled
- Plane is not in current context
- Also don't clear surface updates at end of
commit_plane_for_stream_fast as they are cleared at
the beginning of each flip (only stream updates need
to be cleared in case there is no stream update in
the next flip)
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Allow ABM states to be transferred across display
adapters for smooth display transitions.
[how]
We call DMUB to pause and get ABM states. We
transfer data to other gpu, and deliver data and
ask ABM to un-pause.
Reviewed-by: Harry Vanzylldejong <harry.vanzylldejong@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Reza Amini <reza.amini@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There certain cases where the timing BW is dependent on the type of link
encoding in use. Thus to calculate the correct BW required for a given
timing, the link encoding should be added as a parameter.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current BW calculations do not account for the additional padding added
for uncompressed pixel-to-symbol packing.
This results in X.Y being too low for 128b/132b SST streams in certain
scenarios. If X.Y is too low, end user can observe image corruption.
[How]
Add function to calculate stream overhead to timing BW calculation for
128b/132b SST cases.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Setup stream encoder before link enable for TMDS
- Use is_dig_enable function instead of dcn10 hardcode
- Re-add aux intercept disable delay generically for 2+ LTTPRs
- Add polling method to handle MST reply packet
- Remove unused function
- Improve the include of header file
- Add missing static
- Hardcode vco_freq for dcn316
- Reduce stack size
- Skip enabling DMCUB when using emulation
- Check TG is non-null before checking if enabled
- Update scaler recout data for visual confirm
- Skip querying caps when DMCUB emulation is in use
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Want to further constrain these refresh rate conditions for SubVP:
- SubVP + SubVP: either both <= 120Hz or both between 120-165Hz
- SubVP + DRR: SubVP <= 120Hz
- SubVP + VBlank: SubVP <= 120Hz
[How]
Add constraints in subvp_subvp_admissable(),
dcn32_subvp_drr_admissable() and dcn32_subvp_vblank_admissable()
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We return false by default when link training fail at link loss.
It will cause we get a fail verified link caps directly.
[HOW]
Record the highest verified link caps. Use the recorded value as
the verified link caps if it is not successful in the last attempt
to avoid to use the lowest link setting.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Zhikai Zhai <zhikai.zhai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When RCO is enabled for symclk32_le we get failures during
DP2 link traing compliance tests.
[How]
Break out symclk32_le RCO into a separate function that is
called for hpo when link is enabled/disabled.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to save the cached backlight level so that display lights up using
appropriate brightness level instead of the default brightness when
waking up from s0i3.
[How]
Adding a backlight level cache in link structure. Also instead on
calling set_default_brightness_aux, check if cached values exists.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Workaround to avoid accessing DMCUB state too early if the emulator
is in use - we don't support any of the features the caps are querying
with emulation anyway.
[How]
Guard the query if emulation is in use.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Visual confirm color is not as expected for Autoa Color Management
feature test.
[How]
Calculate scaler recout data when visual confirm enabled to update
the visual confirm bar on the display.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Leo Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is no need to calculate the VCO frequency. In our internal branch
we've hard-coded this for a while, so it's well-tested. This also allows
us to remove the now unused code for calculating the VCO frequency.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Alan Liu <haoping.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This can differ depending on ASIC and we can end up skipping all
transmitter control if we're relying on the wrong bit as a shortcut
for whether link is on/off.
[How]
The ASIC table itself provides the correct DIG check, use that instead
of the dcn10 hardcode.
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDMI spec requires TMDS clock to be not more than 340MHz. Stream encoder ensure
this requirement but driver enable stream encoder later than PHY. So PHY will
output full speed TMDS clock first.
[How]
Enable stream encoder first in TMDS case.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alan Liu <haoping.liu@amd.com>
Signed-off-by: JinZe Xu <jinze.xu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
DCN301 does not have FAMS hence the workaround needed on other DCN3x
variants related to OTG min/max selector programming is not applicable for it.
Hence isolate it and have it use the old sequence without workaround.
Fixes: 1598fc5764 ("drm/amd/display: Program OTG vtotal min/max selectors unconditionally for DCN1+")
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Make a few functions non static so that they can be reused for other
asic. This is in preparation for separating out OTG programming sequence
for DCN301
Fixes: 1598fc5764 ("drm/amd/display: Program OTG vtotal min/max selectors unconditionally for DCN1+")
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It is possible to commit state multiple times in rapid succession with
FAMS enabled; if each of these commits were to set optimized_required,
then the user may see latency.
[HOW]
fw_based_mclk_switching is currently not used in dc->clk_mgr; use it
to track whether the current state has FAMS enabled;
if it has, then do not disable FAMS in prepare_bandwidth, and do not set
optimized_required.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Writing to DRR registers such as OTG_V_TOTAL_MIN on the same frame as a
pipe commit can cause underflow.
[HOW]
Move DMUB p-state delegate into optimze_bandwidth; enabling FAMS sets
optimized_required.
This change expects that Freesync requests are blocked when
optimized_required is true.
Fixes: 613a7956de ("drm/amd/display: Add monitor specific edid quirk")
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
