[why]
Based on power measurement result, in most cases when display clock is higher
than Vmin display clock, lowering display clock using dynamic ODM will improve
overall power consumption by 0 to 4 watts even if we can't reach Vmin.
[how]
Allow vmin optimization applied even if dispclk can't reach Vmin.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The mux to switch between refclk and dto_dsc_clk is non double buffered.
However dto dsc clk's phase and modulo divider registers are currently
configured as double buffered update. This causes a problem when we switch to
use dto dsc clk and program phase and modulo in the same sequence. In this
sequence dsc clk is switched to dto but the clock divider programming doesn't
take effect until next frame. When we try to program DSCC registers, SMN bus
will hang because dto dsc clk divider phase is set to 0.
[how]
Configure phase and modulo to take effect immediately. Always switch to dto dsc
clk before DSC clock is unagted. Switch back to refclk after DSC clock is gated.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When assert in dp_retrieve_lttpr_cap() is hit, dmesg has traces like:
RIP: 0010:dp_retrieve_lttpr_cap+0xcc/0x1a0 [amdgpu]
Call Trace:
<TASK>
dp_retrieve_lttpr_cap+0xcc/0x1a0 [amdgpu]
report_bug+0x1e8/0x240
handle_bug+0x46/0x80
link_detect+0x35/0x580 [amdgpu]
It happens when LTTPRs fail to increment dpcd repeater count.
We have a recovery action in place for such cases.
Assert is misleading, an indicative error in dmesg is more useful.
[How]
Remove ASSERT and use DC_LOG_ERROR instead.
Reviewed-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
For no plane scenarios we should not consider cursor as there cannot
be any cursor if there's no planes. This fixes an issue where
dc_commit_streams fails due to prefetch bandwidth requirements
(the display config + dummy planes + cursor causes the prefetch
bandwidth to exceed what is possible).
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Update coefficients and LUT tables for scaler and sharpener
to improve quality and support different use cases (SDR/HDR)
[How]
Move scaler coefficients to new file dc_spl_scl_easf_filters.c
Remove older coefficients file dc_sp_scl_filters_old.c
Update default taps for EASF support
Update LLS policy for DON'T CARE case
Update cositing offset from 0.5 to 0.25
Add support to adjust sharpness based on level, use case,
and scaling ratio ( using discrete levels )
Apply sharpness to all RGB surfaces and both NV12 and P010
video ( in fullscreen only ). Upscale and 1:1 ratios only
Enable scaler when sharpening 1:1 ratios
Add support for coefficients that are in S1.10 format
(convert to S1.12 format)
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The VRR need to be supported for panel replay feature.
If VRR capability is false, panel replay capability also
need to be disabled.
[How]
After update the vrr capability, the panel replay capability
also need to be check if need.
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commit is a part of a series that addresses the following build
warning for opp:
./drivers/gpu/drm/amd/display/dc/inc/hw/opp.h:1: warning: no structured
comments found
./drivers/gpu/drm/amd/display/dc/inc/hw/dpp.h:1: warning: no structured
comments found
This commit fixes this issue by adding a simple kernel-doc to a struct
in the opp.h and the dpp.h files.
Cc: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When building the kernel-doc, it complains with the below warning:
./drivers/gpu/drm/amd/display/dc/link/hwss/link_hwss_dio.h:1: warning: no structured comments found
./drivers/gpu/drm/amd/display/dc/link/hwss/link_hwss_dio.h:1: warning: no structured comments found
This warning was caused by the wrong use of the ':export:' and the lack
of function documentation in the file pointed under the ':internal:'.
This commit addresses those issues by relocating the overview
documentation to the correct C file, removing the ':export:' options,
and adding two simple kernel-doc to ensure that ':internal:' does not
have any warning.
Cc: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/dri-devel/20240715085918.68f5ecc9@canb.auug.org.au/
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enables following UMD stable Pstates profile levels
of power_dpm_force_performance_level for SMU v14.0.4.
- profile_peak
- profile_min_mclk
- profile_min_sclk
- profile_standard
Signed-off-by: Li Ma <li.ma@amd.com>
Reviewed-by: Tim Huang <tim.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was intended to add support for GFX IP v11.5.2, but it needs
to be applied to all GFX11 and subsequent APUs. Therefore the code
should be revised to accommodate this.
Signed-off-by: Tim Huang <tim.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For unified queue, DPG pause for encoding is done inside VCN firmware,
so there is no need to pause dpg based on ring type in kernel.
For VCN3 and below, pausing DPG for encoding in kernel is still needed.
v2: add more comments
v3: update commit message
Signed-off-by: Boyuan Zhang <boyuan.zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Ruijing Dong <ruijing.dong@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Increase the KMS minor version to indicate GFX12 DCC support since this
contains a major change in how DCC is managed across IPs like GFX, DCN
etc. This will be used mainly by userspace like Mesa to figure out
DCC support on GFX12 hardware.
v2: fix version number (Alex)
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When the `power_saving_policy` property is set to bit mask
"Require color accuracy" ABM should be disabled immediately and
any requests by sysfs to update will return an -EBUSY error.
When the `power_saving_policy` property is set to bit mask
"Require low latency" PSR should be disabled.
When the property is restored to an empty bit mask ABM and PSR
can be enabled again.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240703051722.328-3-mario.limonciello@amd.com
The problem case is as follows:
1. GPU A triggers a gpu ras reset, and GPU A drives
GPU B to also perform a gpu ras reset.
2. After gpu B ras reset started, gpu B queried a DE
data. Since the DE data was queried in the ras reset
thread instead of the page retirement thread, bad
page retirement work would not be triggered. Then
even if all gpu resets are completed, the bad pages
will be cached in RAM until GPU B's bad page retirement
work is triggered again and then saved to eeprom.
This patch can save the bad pages to eeprom in time after gpu
ras reset is completed.
v2:
1. Add the above description to code comments.
2. Reuse existing function.
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Before uninstalling gpu driver, flush all cached ras
bad pages to eeprom.
v2:
Put the same code into a function and reuse the function.
Signed-off-by: YiPeng Chai <YiPeng.Chai@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX ME right now is one but this could change in
future SOC's. Use no of ME for GFX as start point
for ME for compute for GFX12.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To enable mesa to use display dcc, DM should expose them in the
supported modifiers. Add the best (most efficient) modifiers first.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX ME right now is one but this could change in
future SOC's. Use no of ME for GFX as start point
for ME for compute for GFX11.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX ME right now is one but this could change in
future SOC's. Use no of ME for GFX as start point
for ME for compute for GFX10.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Why:
If the reg mmMP1_SMN_C2PMSG_90 is being written to during amdgpu driver
load or driver unload, subsequent amdgpu driver load will fail at
smu_hw_init. The default of mmMP1_SMN_C2PMSG_90 register at a clean
environment is 0x1 and if value differs from expected, amdgpu driver
load will fail.
How to fix:
Ignore the initial value in smu response register before the first smu
message is sent,if smc in SMU_FW_INIT state, just proceed further to
send the message. If register holds an unexpected value after smu message
was sent set, smc_state to SMU_FW_HANG state and no further smu messages
will be sent.
v2:
Set SMU_FW_INIT state at the start of smu hw_init/resume.
Check smc_fw_state before sending smu message if in hang state skip
sending message.
Set SMU_FW_HANG only in case unexpected value is detected
Signed-off-by: Danijel Slivka <danijel.slivka@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For SOCs with GFX v9.4.3, a VF may have multiple compute partitions.
Fetch the partition information during init and initialize partition
nodes. There is no support to switch partition mode in VF mode, hence
disable the same.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
sdma has 2 instances in SRIOV cpx mode. Odd numbered VFs have
sdma0/sdma1 instances. Even numbered vfs have sdma2/sdma3. For
Even numbered vfs, the sdma2 & sdma3 (irq srouce id
CLIENTID_SDMA2 and CLIENTID_SDMA3) should map to irq seq 0 & 1.
Signed-off-by: Gavin Wan <Gavin.Wan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To address the problem with hitches moving when bulk move
sublists are lru-bumped, register the list cursors with the
ttm_lru_bulk_move structure when traversing its list, and
when lru-bumping the list, move the cursor hitch to the tail.
This also means it's mandatory for drivers to call
ttm_lru_bulk_move_init() and ttm_lru_bulk_move_fini() when
initializing and finalizing the bulk move structure, so add
those calls to the amdgpu- and xe driver.
Compared to v1 this is slightly more code but less fragile
and hopefully easier to understand.
Changes in previous series:
- Completely rework the functionality
- Avoid a NULL pointer dereference assigning manager->mem_type
- Remove some leftover code causing build problems
v2:
- For hitch bulk tail moves, store the mem_type in the cursor
instead of with the manager.
v3:
- Remove leftover mem_type member from change in v2.
v6:
- Add some lockdep asserts (Matthew Brost)
- Avoid NULL pointer dereference (Matthew Brost)
- No need to check bo->resource before dereferencing
bo->bulk_move (Matthew Brost)
Cc: Christian König <christian.koenig@amd.com>
Cc: Somalapuram Amaranath <Amaranath.Somalapuram@amd.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: <dri-devel@lists.freedesktop.org>
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240705153206.68526-5-thomas.hellstrom@linux.intel.com
Signed-off-by: Christian König <christian.koenig@amd.com>
to avoid reading wrong WPTR from doorbell in sriov vf, set
CP_HQD_PQ_DOORBELL_CONTROL.DOORBELL_MODE to 1 to read WPTR from MQD.
Signed-off-by: Zhigang Luo <Zhigang.Luo@amd.com>
Acked-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
V1: This patch enables following UMD stable Pstates profile
levels for power_dpm_force_performance_level interface.
- profile_peak
- profile_min_mclk
- profile_min_sclk
- profile_standard
V2: Fix conflict with commit "drm/amd/pm: smu v14.0.4 reuse smu v14.0.0 dpmtable "
V3: Add VCLK1 and DCLK1 support for SMU V14.0.1
And avoid to set VCLK1 and DCLK1 for SMU v14.0.0
Signed-off-by: Li Ma <li.ma@amd.com>
Reviewed-by: Tim Huang <tim.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
