This greater-than-or-equal-to-zero comparison of an unsigned value is always true. fpriv->xcp_id >= 0U
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Reviewed-by: Tim Huang <Tim.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We are incorrectly passing the first XCC's MQD when
updating CU masks for other XCCs in the partition. Fix
this by passing the MQD for the XCC currently being
updated with CU mask to update_cu_mask function.
Fixes: fc6efed2c7 ("drm/amdkfd: Update CU masking for GFX 9.4.3")
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Read default boot options
- Find max flickerless instant vtotal delta
- Refactor dcn401_update_clocks
- Reduce I2C speed to 95kHz in DCN401
- Allow higher DSC slice support for small timings on dcn401
- Don't offload flip if not only address update
- Check UHBR13.5 cap when determining max link cap
- Enable SYMCLK gating in DCCG
- Expand to higher link rates
- Add left edge pixel for YCbCr422/420 + ODM pipe split
- Add resource interfaces for get ODM slice rect
- Add COEF filter types for DCN401
- Refactor DCN401 DCCG into component directory
- Fix 3dlut size for Fastloading on DCN401
- Fix write to non-existent reg on DCN401
- Remove USBC check for DCN32
- Remove unused code for some dc files
- Disable AC/DC codepath when unnecessary
- Create dcn401_clk_mgr struct
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
- Populate dml 2 callback with get_max_flickerless_instant_vtotal_increase
- Use long long when necessary to prevent overflow
- Add asic specific default values, currently disabled by
default for every asic
- Use the pre-existing debug option to protect the call to
get_max_flickerless_instant_vtotal_increase
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ethan Bitnun <etbitnun@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HW for DCN401 is presented with a small I2C speed fluctuation that
exceeds the hard cap limitation of 100kHz occasionally. This violates
compliance requirement and will result in failure in compliance.
[HOW]
After various measurements and traceback to previous generation HW, DCN IP,
SI and SW driver agrees that we can reduce I2C speed to 95kHz to address
the I2C spped fluctuation in DCN401.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DML2.1 has added the support to determine ODM combine based on DSC slice
count limitation. This support would allow us to support DSC slice higher
than 4 on small timings. The change will allow higher DSC slice support
independent from pixel clock in use.
[HOW]
Add a DCN401 get_enc_caps function to allow the support for DSC slice count
higher than 4.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Fast updates can consist of some stream updates as well (i.e., out_csc).
In these cases we should not offload the flip to FW as we can only
offload address only updates to FW.
Reviewed-by: Chris Park <chris.park@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
UHBR13.5 support is optional, even if UHBR20 is supported by the device.
If source supports max UHBR13.5 while sink, cable and LTTPR support
UHBR20 but not UHBR13.5, UHBR10 should be used as the max link cap.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently 3-tap chroma subsampling is used for YCbCr422/420. When ODM
pipesplit is used, pixels on the left edge of ODM slices need one extra
pixel from the right edge of the previous slice to calculate the correct
chroma value.
Without this change, the chroma value is slightly different than
expected. This is usually imperceptible visually, but it impacts test
pattern CRCs for compliance test automation.
[HOW]
Update logic to use the register for adding extra left edge pixel for
YCbCr422/420 ODM cases.
Reviewed-by: George Shen <george.shen@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The CONNECTOR_ID_USBC check was removed to fix a regression, but it was
re-introduced by accident. This commit drops the USBC that causes the
regressions.
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
If there are no DC clock limits present, or if the DC limits are the same
as the AC limits, we can disable the AC/DC codepath as there won't be any
validation differences between the two modes.
[HOW]
When all DC power mode clock limits are the same as the max clock
values, there won't be any difference between AC mode and DC mode. Zero
out DC limits that equal max and provide a new cap to indicate the
presence of any non-zero DC mode limit. In summary:
- zero out DC limits that are the same as max clock value
- new dc cap to indicate the presence of DC mode limits
- set limits present if any clock has distinct AC and DC values from SMU
Acked-by: Alex Hung <alex.hung@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Added support to capture unsch fw debug logs in debugfs.
To enable set amdgpu_umschfw_log =1 in boot args.
v1 - rename variable to umsch_mm_fwlog (Veera)
Signed-off-by: Saleemkhan Jamadar <saleemkhan.jamadar@amd.com>
Reviewed-by: Veerabadhran Gopalakrishnan <Veerabadhran.Gopalakrishnan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On suspend, we need to set power gating state to GATE when
VCN5 is busy, otherwise we will get following error on resume:
[drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring vcn_unified_0 test failed (-110)
[drm:amdgpu_device_ip_resume_phase2 [amdgpu]] *ERROR* resume of IP block <vcn_v5_0_0> failed -110
amdgpu: amdgpu_device_ip_resume failed (-110).
PM: dpm_run_callback(): pci_pm_resume+0x0/0x100 returns -110
PM: failed to resume async: error -110
Signed-off-by: David (Ming Qiang) Wu <David.Wu3@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We do not directly enable/disable VCN IRQ in vcn 5.0.0.
And we do not handle the IRQ state as well. So the calls to
disable IRQ and set state are removed. This effectively gets
rid of the warining of
"WARN_ON(!amdgpu_irq_enabled(adev, src, type))"
in amdgpu_irq_put().
Signed-off-by: David (Ming Qiang) Wu <David.Wu3@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check the input value for CUSTOM profile mode setting on smu 11,
smu13 and smu14. Otherwise we use uninitialized value of input[]
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check the input value for CUSTOM profile mode setting on legacy
SOCs. Otherwise we may use uninitalized value of input[]
Signed-off-by: Ma Jun <Jun.Ma2@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Support for I2C_CLASS_SPD is currently being removed from the kernel.
Only remaining step is to remove the definition of I2C_CLASS_SPD.
Setting I2C_CLASS_SPD in a driver is a no-op meanwhile, so remove it
here.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Analysis of code by Coverity, a static code analyser, has identified
a resource leak in the symbol hmm_range. This leak occurs when one of
the prior steps before it is released encounters an error.
Signed-off-by: Ramesh Errabolu <Ramesh.Errabolu@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On system with khugepaged enabled and user cases with THP buffer, the
hmm_range_fault may takes > 15 seconds to return -EBUSY, the arbitrary
timeout value is not accurate, cause memory allocation failure.
Remove the arbitrary timeout value, return EAGAIN to application if
hmm_range_fault return EBUSY, then userspace libdrm and Thunk will call
ioctl again.
Change EAGAIN to debug message as this is not error.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We don't get the right offset in that case. The GPU has
an unused 4K area of the register BAR space into which you can
remap registers. We remap the HDP flush registers into this
space to allow userspace (CPU or GPU) to flush the HDP when it
updates VRAM. However, on systems with >4K pages, we end up
exposing PAGE_SIZE of MMIO space.
Fixes: d8e408a827 ("drm/amdkfd: Expose HDP registers to user space")
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Kbuild conventionally uses $(obj)/ for generated files, and $(src)/ for
checked-in source files. It is merely a convention without any functional
difference. In fact, $(obj) and $(src) are exactly the same, as defined
in scripts/Makefile.build:
src := $(obj)
When the kernel is built in a separate output directory, $(src) does
not accurately reflect the source directory location. While Kbuild
resolves this discrepancy by specifying VPATH=$(srctree) to search for
source files, it does not cover all cases. For example, when adding a
header search path for local headers, -I$(srctree)/$(src) is typically
passed to the compiler.
This introduces inconsistency between upstream and downstream Makefiles
because $(src) is used instead of $(srctree)/$(src) for the latter.
To address this inconsistency, this commit changes the semantics of
$(src) so that it always points to the directory in the source tree.
Going forward, the variables used in Makefiles will have the following
meanings:
$(obj) - directory in the object tree
$(src) - directory in the source tree (changed by this commit)
$(objtree) - the top of the kernel object tree
$(srctree) - the top of the kernel source tree
Consequently, $(srctree)/$(src) in upstream Makefiles need to be replaced
with $(src).
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
Currently oem_id is defined as uint8_t[6] and casted to uint64_t*
in some use case. This would lead code scanner to complain about
access beyond. Re-define it in union to enforce 8-byte size and
alignment to avoid potential issue.
Signed-off-by: Michael Chen <michael.chen@amd.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit c37ce764cd.
RCCL library is currently not treating spatial partitions differently,
hence this change is causing issues. Revert temporarily till RCCL
implementation is ready for spatial partitions.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Jonathan Kim <jonathan.kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some older MST hubs do not report DPCD registers according to
specification.
[How]
This change re-applies commit c536555451 ("drm/amd/display: dsc mst
re-compute pbn for changes on hub").
With an additional check for these older MST devices.
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This fixes a bug introduced by commit c536555451 ("drm/amd/display: dsc
mst re-compute pbn for changes on hub").
The change caused light-up issues with a second display that required
DSC on some MST docks.
[How]
Use Virtual DPCD for DSC caps in MST case.
[Limitations]
This change only affects MST DSC devices that follow specifications
additional changes are required to check for old MST DSC devices such as
ones which do not check for Virtual DPCD registers.
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
