Add max_tmds_clock validation to prepare for additions and changes to
the MPLL config table. Use the same rate restrictions that is currently
applied.
The rate limit for RK3288, RK3399 and RK3568 is based on current mpll
table. The rate limit for RK3228 and RK3328 is based on the
inno-hdmi-phy pre-pll table.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240615170417.3134517-7-jonas@kwiboo.se
EDID cannot be read on RK3328 until after read_hpd has been called and
correct io voltage has been configured based on connection status.
When a forced mode is used, e.g. video=1920x1080@60e, the connector
detect ops, that in turn normally calls the read_hpd, never gets called.
This result in reading EDID to fail in connector get_modes ops.
Call dw_hdmi_rk3328_read_hpd at end of dw_hdmi_rk3328_setup_hpd to
correct io voltage and allow reading EDID after setup_hpd.
Fixes: 1c53ba8f22 ("drm/rockchip: dw_hdmi: add dw-hdmi support for the rk3328")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240615170417.3134517-5-jonas@kwiboo.se
-ENODEV is used to signify that there is no zap shader for the platform,
and the CPU can directly take the GPU out of secure mode. We want to
use this return code when there is no zap-shader node. But not when
there is, but without a firmware-name property. This case we want to
treat as-if the needed fw is not found.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/604564/
Disable bit 29 of SCLKGATE_DIS register around pps sequence
when we turn panel power on.
--v2
-Squash two commit together [Jani]
-Use IS_DISPLAY_VER [Jani]
-Fix multiline comment [Jani]
--v3
-Define register in a more appropriate place [Mitul]
--v4
-Register is already defined no need to define it again [Ville]
-Use correct WA number (lineage no.) [Dnyaneshwar]
-Fix the range on which this WA is applied [Dnyaneshwar]
Bspec: 49304
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240813042807.4015214-1-suraj.kandpal@intel.com
We are checking cp_irq_count from the wrong hdcp structure which
ends up giving timed out errors. We only increment the cp_irq_count
of the primary connector's hdcp structure but here in case of
multidisplay setup we end up checking the secondary connector's hdcp
structure, which will not have its cp_irq_count incremented. This leads
to a timed out at CP_IRQ error even though a CP_IRQ was raised. Extract
it from the correct intel_hdcp structure.
--v2
-Explain why it was the wrong hdcp structure [Jani]
Fixes: 8c9e4f68b8 ("drm/i915/hdcp: Use per-device debugs")
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240809114127.3940699-2-suraj.kandpal@intel.com
Having two methods to wait on GT TLB invalidations is not ideal. Remove
xe_gt_tlb_invalidation_wait and only use GT TLB invalidation fences.
In addition to two methods being less than ideal, once GT TLB
invalidations are coalesced the seqno cannot be assigned during
xe_gt_tlb_invalidation_ggtt/range. Thus xe_gt_tlb_invalidation_wait
would not have a seqno to wait one. A fence however can be armed and
later signaled.
v3:
- Add explaination about coalescing to commit message
v4:
- Don't put dma fence if defined on stack (CI)
v5:
- Initialize ret to zero (CI)
v6:
- Use invalidation_fence_signal helper in tlb timeout (Matthew Auld)
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240719172905.1527927-3-matthew.brost@intel.com
(cherry picked from commit 61ac035361)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
When validating VF config on the media GT, we may wrongly report
that VF is already partially configured on it, as we consider GGTT
and LMEM provisioning done on the primary GT (since both GGTT and
LMEM are tile-level resources, not a GT-level).
This will cause skipping a VF auto-provisioning on the media-GT and
in result will block a VF from successfully initialize that GT.
Fix that by considering GGTT and LMEM configurations only when
checking if a VF provisioning is complete, and omit GGTT and LMEM
when reporting empty/partial provisioning.
Fixes: 234670cea9 ("drm/xe/pf: Skip fair VFs provisioning if already provisioned")
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Piotr Piórkowski <piotr.piorkowski@intel.com>
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240806180516.618-1-michal.wajdeczko@intel.com
(cherry picked from commit 5bdacb0907)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The mpll_cfg, cur_ctr and phy_config members in struct dw_hdmi_plat_data
are only used to configure the Synopsys PHYs supported internally by DW
HDMI transmitter driver (gpu/drm/bridge/synopsys/dw-hdmi.c), via
hdmi_phy_configure_dwc_hdmi_3d_tx(), which is further invoked from
dw_hdmi_phy_init(). This is part of the internal
dw_hdmi_synopsys_phy_ops struct, managed within dw_hdmi_detect_phy().
To handle vendor PHYs, DW HDMI driver doesn't make use of the internal
PHY ops and, instead, relies on the glue layer to provide the phy_ops
and phy_name members of struct dw_hdmi_plat_data.
Drop the unnecessary assignments of DW internal PHY related members from
structs rk3228_hdmi_drv_data and rk3328_hdmi_drv_data, since both set
the phy_force_vendor flag and correctly provide the expected vendor PHY
data.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240813-dw-hdmi-rockchip-cleanup-v1-4-b3e73b5f4fd6@collabora.com
The RK3066 VOP sets a dma_stop bit when it's done scanning out a frame
and needs the driver to acknowledge that by clearing the bit.
Unless we clear it "between" frames, the RGB output only shows noise
instead of the picture. atomic_flush is the place for it that least
affects other code (doing it on vblank would require converting all
other usages of the reg_lock to spin_(un)lock_irq, which would affect
performance for everyone).
This seems to be a redundant synchronization mechanism that was removed
in later iterations of the VOP hardware block.
Fixes: f4a6de855e ("drm: rockchip: vop: add rk3066 vop definitions")
Cc: stable@vger.kernel.org
Signed-off-by: Val Packett <val@packett.cool>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240624204054.5524-2-val@packett.cool
xe_gt_enable_host_l2_vram() is reading the XE2_GAMREQSTRM_CTRL register
that is currently missing the MCR annotation. However, just adding the
annotation doesn't work as this function is called before MCR handling
is initialized in xe_gt_mcr_init().
xe_gt_enable_host_l2_vram() is used to implement WA 16023588340 that
needs to be done as early as possible during initialization in order to
be effective since the MMIO writes impact it. In the failure scenario,
driver would simply not be able to bind successfully.
Moving xe_gt_enable_host_l2_vram() later, after MCR initialization is
done, only incurs a few additional HW accesses, particularly when
loading GuC for hwconfig. Binding/unbinding the driver 100 times in BMG
still works so it should be ok to start handling the WA a little bit
later. This is sufficient to allow adding the MCR annotation to
XE2_GAMREQSTRM_CTRL.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Tejas Upadhyay <tejas.upadhyay@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240814095614.909774-2-tejas.upadhyay@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
The different approach used by xe regarding the initialization of
display HW has been proved a great addition for early driver bring up:
core xe can be tested without having all the bits sorted out on the
display side.
On the other hand, the approach exposed by i915-display is to *actively*
disable the display by programming it if needed, i.e. if it was left
enabled by firmware. It also has its use to make sure the HW is actually
disabled and not wasting power.
However having both the way it is in xe doesn't expose a good interface
wrt module params. From modinfo:
disable_display:Disable display (default: false) (bool)
enable_display:Enable display (bool)
Rename enable_display to probe_display to try to convey the message that
the HW is being touched and improve the module param description. To
avoid confusion, the enable_display is renamed everywhere, not only in
the module param. New description for the parameters:
disable_display:Disable display (default: false) (bool)
probe_display:Probe display HW, otherwise it's left untouched (default: true) (bool)
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240813141931.3141395-1-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
