Rectify the logical value of reset-gpio so that it is set to
0 (disabled) during power-on and to 1 (enabled) during power-off.
Set the reset-gpio to GPIO_OUT_HIGH at initialization time to make
sure it starts off in reset. Also drop the "Set XCLR" comment which
is not-so-informative.
The existing usage of imx335 had reset-gpios polarity inverted
(GPIO_ACTIVE_HIGH) in their device-tree sources. With this patch
included, those DTS will not be able to stream imx335 anymore. The
reset-gpio polarity will need to be rectified in the device-tree
sources as shown in [1] example, in order to get imx335 functional
again (as it remains in reset prior to this fix).
Cc: stable@vger.kernel.org
Fixes: 45d19b5fb9 ("media: i2c: Add imx335 camera sensor driver")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/linux-media/20240729110437.199428-1-umang.jain@ideasonboard.com/
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Omnivision OG01A1B camera sensor is supplied by three power rails,
if supplies are present as device properties, include them into
sensor power up sequence.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The OmniVision OG01A1B camera sensor has an xvclk supply clock, which
could be described and then explicitly controlled on OF platforms.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
[Sakari Ailus: Use UL specifier for power-up delay cycle value.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The OmniVision OG01A1B image sensor driver currently supports probing
only on ACPI platforms, the changes adds support of OF platforms to
the driver.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Commit 2989a45717 ("media: ccs: Refactor register reading a little")
removed ccs_read_addr_no_quirk() but left declaration.
Commit 529322112a ("media: ccs: Use V4L2 CCI for accessing sensor
registers") removed ccs_write_addr_no_quirk() and ccs_reg_width() but
leave their declarations.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The ov5675 specification says that the gap between XSHUTDN deassert and the
first I2C transaction should be a minimum of 8192 XVCLK cycles.
Right now we use a usleep_rage() that gives a sleep time of between about
430 and 860 microseconds.
On the Lenovo X13s we have observed that in about 1/20 cases the current
timing is too tight and we start transacting before the ov5675's reset
cycle completes, leading to I2C bus transaction failures.
The reset racing is sometimes triggered at initial chip probe but, more
usually on a subsequent power-off/power-on cycle e.g.
[ 71.451662] ov5675 24-0010: failed to write reg 0x0103. error = -5
[ 71.451686] ov5675 24-0010: failed to set plls
The current quiescence period we have is too tight. Instead of expressing
the post reset delay in terms of the current XVCLK this patch converts the
power-on and power-off delays to the maximum theoretical delay @ 6 MHz with
an additional buffer.
1.365 milliseconds on the power-on path is 1.5 milliseconds with grace.
85.3 microseconds on the power-off path is 90 microseconds with grace.
Fixes: 49d9ad719e ("media: ov5675: add device-tree support and support runtime PM")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Tested-by: Quentin Schulz <quentin.schulz@cherry.de> # RK3399 Puma with
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Smatch is very confused by a clk_prepare_enable() being called in an
error-path. Fix this warning by moving the clk_prepare_enable() to its
own function.
drivers/media/i2c/tc358746.c:1631 tc358746_suspend() warn: 'tc358746->refclk' from clk_prepare_enable() not released on lines: 1631.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Smatch is very confused by a clk_prepare_enable() being called in an
error-path. Fix this warning by moving the clk_prepare_enable() to its
own function.
drivers/media/i2c/s5c73m3/s5c73m3-core.c:1425 __s5c73m3_power_off() warn: 'state->clock' from clk_prepare_enable() not released on lines: 1425.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Factor out all the power off logic, except clk_disable_unprepare(), to a
new function __ov5645_set_power_off().
This allows ov5645_set_power_on() to excplicitly clean-out the clock
during the error-path.
The following smatch warning is fixed:
drivers/media/i2c/ov5645.c:690 ov5645_set_power_on() warn: 'ov5645->xclk' from clk_prepare_enable() not released on lines: 690.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Factor out all the power off logic, except the clk_disable_unprepare(),
to a new function __ar0521_power_off().
This allows ar0521_power_on() to explicitly clean-out the clock during
the error-path.
The following smatch warning is fixed:
drivers/media/i2c/ar0521.c:912 ar0521_power_on() warn: 'sensor->extclk' from clk_prepare_enable() not released on lines: 912.
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The driver has an OF match table, still, it uses an ID lookup table for
retrieving match data. Currently, the driver is working on the
assumption that an I2C device registered via OF will always match a
legacy I2C device ID. The correct approach is to have an OF device ID
table using i2c_get_match_data() if the devices are registered via OF/ID.
Unify the OF/ID table by using MEDIA_BUS_FMT as match data for both these
tables and replace the ID lookup table for the match data by
i2c_get_match_data() and simplifly probe() and mt9p031_init_state().
While at it, remove the trailing comma in the terminator entry for the OF
table making code robust against (theoretical) misrebases or other similar
things where the new entry goes _after_ the termination without the
compiler noticing.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20230910160126.70122-2-biju.das.jz@bp.renesas.com
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
`tda1997x_codec_driver` is not modified after its declaration, and it
is only passed to `devm_snd_soc_register_component()`, which expects
a constant `snd_soc_component_driver`.
Move `tda1997x_codec_driver` to a read-only section by declaring it
const.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There is a spelling mistake in a string in the gc05a2_test_pattern_menu
array. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
While add it, also remove commas after the sentinel entries.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
'vbi_ram_default' and 'tvp5150_config' are not modified in this diver
and are only used as a const struct.
Constifying these structures moves some data to a read-only section, so
increase overall security.
On a x86_64, with allmodconfig:
Before:
text data bss dec hex filename
57197 2936 36 60169 eb09 drivers/media/i2c/tvp5150.o
After:
text data bss dec hex filename
57517 2608 36 60161 eb01 drivers/media/i2c/tvp5150.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
With ARCH=x86, make allmodconfig && make W=1 C=1 reports:
WARNING: modpost: missing MODULE_DESCRIPTION() in drivers/media/i2c/uda1342.o
Add the missing invocation of the MODULE_DESCRIPTION() macro.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
- Conversion of max9286 and adv748x to V4L2 subdev active state
- Cleanups and fixes for the Renesas R-Car VSP and VIN drivers
- Miscellaneous cleanups to V4L2 core
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The adv748x-csi2 driver configures the CSI-2 transmitter to
automatically infer the image stream format from the connected
frontend (HDMI or AFE).
Setting a new format on the subdevice hence does not actually control
the CSI-2 output format, but it's only there for the purpose of
pipeline validation.
However, there is currently no validation that the supplied media bus
code is valid and supported by the device.
With the introduction of enum_mbus_codes a list of supported format is
now available, use it to validate that the supplied format is correct
and use the default UYVY8 one if that's not the case.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20240617161135.130719-8-jacopo.mondi@ideasonboard.com
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Rename 'st-vgxy61' to 'vgxy61', dropping the vendor prefix to follow the
same naming scheme as the vast majority of device drivers.
The device tree binding does not fall into binding rename exceptions and
therefore must not be changed. Keep its legacy name.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
