USB4 specification defines the metadata needed to perform software
margining, as well as the necessary steps which include waiting for
dwell time.
- Add dwell_time attribute to set the wait time while performing
margining and checking for link errors.
- Add error_counter attribute to configure error counter prior to
margining test.
- Add voltage_time_offset attribute to set the voltage or time offset
steps before performing the software margining test.
- Perform software margining test for dwell duration, break if there are
link errors, stop the clocks and provide results.
Below is a minimalistic example how this can be used. Note these values
are just examples. The exact values in practice depend on host specific
capabilities and the type of measurement to be performed.
# cd /sys/kernel/debug/thunderbolt/ROUTER/portX/margining/
# echo software > mode
# echo 400 > dwell_time
# echo 1 > run
As usual the results attribute contains the results of a succesfull run.
Signed-off-by: R Kannappan <r.kannappan@intel.com>
Co-developed-by: Rene Sapiens <rene.sapiens@intel.com>
Signed-off-by: Rene Sapiens <rene.sapiens@intel.com>
Co-developed-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add optional extended voltage offset range support for software and
hardware margining as defined by the USB4 specification.
If supported, it can be enabled like below:
# cd /sys/kernel/debug/thunderbolt/ROUTER/portX/margining/
# echo Y > optional_voltage_offset
Signed-off-by: Rene Sapiens <rene.sapiens@intel.com>
Co-developed-by: R Kannappan <r.kannappan@intel.com>
Signed-off-by: R Kannappan <r.kannappan@intel.com>
Co-developed-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Aapo Vienamo <aapo.vienamo@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Retimers support lane margining as well so make this available through
debugfs in the same way as we do for the USB4 ports. When this is
enabled we also expose retimers on the other side of the cable because
typically margining is implemented only on direction towards the cable.
However, for the retimers on the other side of the cable we do not allow
NVM upgrade to avoid confusing the existing userspace (the same retimer
may now appear twice with different name) and is probably not a good
idea anyway.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to add lane margining support for retimers make the margining
functions take sideband target and retimer index as parameters. This
makes it possible to access both router and retimer sideband using the
same functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This makes it possible to read and write USB4 port and retimer sideband
registers through debugfs which is useful for debugging and manufacturing
purposes. We add "sb_regs" debugfs attribute under each USB4 port and
retimer that is used to access the sideband.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It is supposed to be close with the other lane margining functions so
move it there. No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Currently we notify PM core about occurred wakes after any resume. This
is not actually needed after resume from runtime suspend. Hence, notify
PM core about occurred wakes only after resume from system sleep. Also,
if the wake occurred in USB4 router upstream port, we don't notify the
PM core about it since it is not actually needed and can cause
unexpected autowake (e.g. if /sys/power/wakeup_count is used).
While there add the missing kernel-doc for tb_switch_resume().
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since commit aed65af1cc ("drivers: make device_type const"), the driver
core can properly handle constant struct device_type. Move the
tb_domain_type, tb_retimer_type, tb_switch_type, usb4_port_device_type,
tb_service_type and tb_xdomain_type variables to be constant structures as
well, placing it into read-only memory which can not be modified at
runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If a DiplayPort cable is directly connected to the host routers USB4
port, there is no tunnel involved but the port is in "redrive" mode
meaning that it is re-driving the DisplayPort signals from its
DisplayPort source. In this case we need to keep the domain powered on
otherwise once the domain enters D3cold the connected monitor blanks
too.
Since this happens only on Intel Barlow Ridge add a quirk that takes
runtime PM reference if we detect that the USB4 port entered redrive
mode (and release it once it exits the mode).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The USB4 spec says that the Connection Manager should reserve the
bandwidth that is released in the same group for 10 seconds before it
can be shared with other groups. Add support for this. We also delay the
symmetric transition by that same 10 seconds to avoid any unnecessary
transitions (i.e if the released bandwidth is used by another
DisplayPort tunnel in the same group the link can stay asymmetric the
whole time).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Boot firmware (typically BIOS) might have created tunnels of its own.
The tunnel configuration that it does might be sub-optimal. For instance
it may only support HBR2 monitors so the DisplayPort tunnels it created
may limit Linux graphics drivers. In addition there is an issue on some
AMD based systems where the BIOS does not allocate enough PCIe resources
for future topology extension. By resetting the USB4 topology the PCIe
links will be reset as well allowing Linux to re-allocate.
This aligns the behavior with Windows Connection Manager.
We already issued host router reset for USB4 v2 routers, now extend it
to USB4 v1 routers as well. For pre-USB4 (that's Apple systems) we leave
it as is and continue to discover the existing tunnels.
Suggested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This function can be used to clear path config space of an adapter. Make
it available for other files in this driver.
Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Introduce a function that issues Downstream Port Reset to a USB4 port.
This supports Thunderbolt 2, 3 and USB4 routers.
Signed-off-by: Sanath S <Sanath.S@amd.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In case of the link is brought up as asymmetric (due to hardware preference), we
honor that and don't transition it to symmetric, unless a router with symmetric
link got plugged below, in the topology (and a bandwidth allows transition to
symmetric).
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We are going to use it in subsequent patches, so make it available outside of
switch.c. Also, change the name to tb_width_name() to follow the naming
conventions.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 v2 spec defines a Gen 4 link that can operate as an aggregated
symmetric (80/80G) or asymmetric (120/40G). When the link is asymmetric,
the USB4 port on one side of the link operates with three TX lanes and
one RX lane, while the USB4 port on the opposite side of the link
operates with three RX lanes and one TX lane.
Add support for the asymmetric link and provide functions that can be
used to transition the link to asymmetric and back.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This is useful helper to find out the depth of a connected router.
Convert the existing users to call this helper instead of open-coding.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Introduce tb_port_path_direction_downstream() to check if path from
source adapter to destination adapter is directed towards downstream.
Convert existing users to call this helper instead of open-coding.
No functional changes.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 v2 spec allows USB4 links that are part of a pass through tunnel
(such as DisplayPort and USB 3.x Gen T) to enter lower CL states, which
provide better power management. For this USB4 v2 routers in their path
config space of lane 0 adapter include a new bit PMPS (PM packet
support) that needs to be set.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Rework the function to return the link generation, update the name to
tb_port_get_link_generation(), and make available to the rest of the
driver. This is needed in the subsequent patches.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It turns out there is no need to use the actual link rate when
reclaiming bandwidth for USB 3.x. The reason is that we use consumed
bandwidth which is coming from xHCI when releasing bandwidth (for
example for DisplayPort tunneling) and this can be anything between
1000 Mb/s to maximum, so when reclaiming we can just bump it up back to
maximum instead of actual link rate (which is always <= maximum).
This allows us to get rid of couple of unnecessary lines of code.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The software connection manager needs the device links in order to
establish the tunnels before the native protocols so log a warning if
they are not found.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Make sure the DisplayPort bandwidth allocation mode function names are
consistent with the existing ones, such as USB3.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This is new TMU mode introduced with the USB4 v2. This mode is simpler
than the existing ones and allows all CL states as well. Enable this for
all links where both side routers are v2 and keep the existing
functionality for the v1 and earlier links.
Currently only support the MedRes rate. We can add the HiFi rate later
too if it turns out to be useful.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Move constants related to NVM into nvm.c to make the code cleaner. Use a
separate constant for USB4_DATA_DWORDS in usb4.c.
No functional changes.
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 v2 spec introduces modified encapsulation of PCIe TLP and DLLP
packets. This improves the PCIe tunneled traffic usage by reducing
overhead. Enable this if both sides of the link support it.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 v2 bumps the per-lane speed up to 40 Gb/s. Also the lanes are
always bonded which gives 80 Gb/s symmetric link (and 120/40 Gb/s
asymmetric). This updates the speed and width of routers and XDomain
connections to support the Gen 4 link. For now we keep the link as is
even if it is already asymmetric.
While there make tb_port_set_link_width() static.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add a new function usb4_switch_version() that can be used to figure out
the spec version of the router and make tb_switch_is_usb4() to use it as
well. Update the uevent accordingly.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When USB4 port is in offline mode (this mean there is no device
attached) we want to keep the sideband up to make it possible to
communicate with the retimers. In the same way there is no need to
enable sideband transactions when the USB4 port is not offline as they
are already up.
For this reason make the enabling/disabling depend on the USB4 port
offline status.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In case the boot firmware enabled any of them, read the currently
configured CL states and update the router structure accordingly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This is more natural and follows the hardware register layout better.
This makes it easier to see which CL states we enable (even though they
should be enabled together). Rename 'clx_mask' to 'clx' everywhere as
this is now always bitmask.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There really don't belong to switch.c so move them into their own file.
As we do this rename the functions to match the conventions used
elsewhere in the driver.
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This is better to be part of the software connection manager flows in
tb.c. Also name the new function tb_increase_tmu_accuracy() to match
what it actually does.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is no point passing it as we already have a field for that. While
there clean up the kernel-doc of things that do not really belong to the
API documentation (these can be figured out from the spec itself).
No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In the same way we did for the routers add a function that returns the
parent routers downstream facing port for XDomain devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Introduce tb_switch_downstream_port() helper function that returns the
downstream port of a parent switch that is connected to the upstream
port of specified switch. From now on, we use it all across the driver
where applicable.
While there fix a whitespace in comment and rename 'downstream' to
'down' to be consistent with the rest of the driver.
Signed-off-by: Gil Fine <gil.fine@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Current Intel USB4 host routers have hardware limitation that the USB3
bandwidth cannot go higher than 16376 Mb/s. Work this around by adding a
new quirk that limits the bandwidth for the affected host routers.
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
According to USB4 retimer specification, the process of firmware update
sequence requires issuing a SET_INBOUND_SBTX port operation that later
shall be followed by UNSET_INBOUND_SBTX port operation. This last step
is not currently issued by the driver but it is necessary to make sure
the retimers are put back to passthrough mode even during enumeration.
If this step is missing the link may not come up properly after
soft-reboot for example.
For this reason issue UNSET_INBOUND_SBTX after SET_INBOUND_SBTX for
enumeration and also when the NVM upgrade is run.
Reported-by: Christian Schaubschläger <christian.schaubschlaeger@gmx.at>
Link: https://lore.kernel.org/linux-usb/b556f5ed-5ee8-9990-9910-afd60db93310@gmx.at/
Cc: stable@vger.kernel.org
Signed-off-by: Gil Fine <gil.fine@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add QUIRK_NO_CLX to disable the CLx state for hardware which
doesn't supports it.
AMD Yellow Carp and Pink Sardine don't support CLx state,
hence disabling it using QUIRK_NO_CLX.
Cc: stable@vger.kernel.org
Signed-off-by: Sanjay R Mehta <sanju.mehta@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
[mw: added debug log when the quirk is run]
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
The USB4 spec defines an optional feature that allows the connection
manager to negotiate with the graphics through DPCD registers changes in
the bandwidth allocation dynamically. This is referred as "bandwidth
allocation mode" in the spec. The connection manager uses DP IN adapters
registers to communicate with the graphics, and also gets notifications
from these adapters when the graphics wants to change the bandwidth
allocation. Both the connection manager and the graphics driver needs to
support this.
We check if the DP IN adapter supports this and if it does enable it
before establishing a DP tunnel. Then we react on DP_BW notifications
coming from the DP IN adapter and update the bandwidth allocation
accordingly (within the maximum common capabilities the DP IN/OUT
support).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
USB4 spec defines an additional feature that DP IN adapters can
implement (alongside with the graphics DPCD register set) to support
more dynamic bandwidth management for DisplayPort tunnels. For the
connection manager the communication happens through the DP IN adapter
using a set of registers in the adapter config space allocated for this.
Add functions that export this functionality for the rest of the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
tb_port_is_clx_enabled() generates a valid warning with gcc-13:
drivers/thunderbolt/switch.c:1286:6: error: conflicting types for 'tb_port_is_clx_enabled' due to enum/integer mismatch; have 'bool(struct tb_port *, unsigned int)' ...
drivers/thunderbolt/tb.h:1050:6: note: previous declaration of 'tb_port_is_clx_enabled' with type 'bool(struct tb_port *, enum tb_clx)' ...
I.e. the type of the 2nd parameter of tb_port_is_clx_enabled() in the
declaration is unsigned int, while the definition spells enum tb_clx.
Synchronize them to the former as the parameter is in fact a mask of the
enum values.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
