The HDMI TX Parallel Audio Interface (HTX_PAI) is a digital module that
acts as the bridge between the Audio Subsystem to the HDMI TX Controller.
This IP block is found in the HDMI subsystem of the i.MX8MP SoC.
Data received from the audio subsystem can have an arbitrary component
ordering. The HTX_PAI block has integrated muxing options to select which
sections of the 32-bit input data word will be mapped to each IEC60958
field. The HTX_PAI_FIELD_CTRL register contains mux selects to
individually select P,C,U,V,Data, and Preamble.
Use component helper so that imx8mp-hdmi-tx will be aggregate driver,
imx8mp-hdmi-pai will be component driver, then imx8mp-hdmi-pai can use
bind() ops to get the plat_data from imx8mp-hdmi-tx device.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Liu Ying <victor.liu@nxp.com>
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20250923053001.2678596-6-shengjiu.wang@nxp.com
The bridge has three bootstrap pins which are sampled to determine the
frequency of the external reference clock. The driver will also
(over)write that setting. But it seems this is racy after the bridge is
enabled. It was observed that although the driver write the correct
value (by sniffing on the I2C bus), the register has the wrong value.
The datasheet states that the GPIO lines have to be stable for at least
5us after asserting the EN signal. Thus, there seems to be some logic
which samples the GPIO lines and this logic appears to overwrite the
register value which was set by the driver. Waiting 20us after
asserting the EN line resolves this issue.
Fixes: a095f15c00 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250821122341.1257286-1-mwalle@kernel.org
The DW DP TX Controller is compliant with the DisplayPort Specification
Version 1.4 with the following features:
* DisplayPort 1.4a
* Main Link: 1/2/4 lanes
* Main Link Support 1.62Gbps, 2.7Gbps, 5.4Gbps and 8.1Gbps
* AUX channel 1Mbps
* Single Stream Transport(SST)
* Multistream Transport (MST)
* Type-C support (alternate mode)
* HDCP 2.2, HDCP 1.3
* Supports up to 8/10 bits per color component
* Supports RBG, YCbCr4:4:4, YCbCr4:2:2, YCbCr4:2:0
* Pixel clock up to 594MHz
* I2S, SPDIF audio interface
Add library with common helpers to make it can be shared with
other SoC.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20250822063959.692098-3-andyshrk@163.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
drm-misc-next for v6.18:
UAPI Changes:
- Add DRM_IOCTL_GEM_CHANGE_HANDLE for reassigning GEM handles
- Document DRM_MODE_PAGE_FLIP_EVENT
Cross-subsystem Changes:
fbcon:
- Add missing declarations in fbcon.h
Core Changes:
bridge:
- Fix ref counting
panel:
- Replace and remove mipi_dsi_generic_write_{seq/_chatty}()
sched:
- Fixes
Rust:
- Drop Opaque<> from ioctl arguments
Driver Changes:
amdxdma:
- Support buffers allocated by user space
- Streamline PM interfaces
- Fixes
bridge:
- cdns-dsi: Various improvements to mode setting
- Support Solomon SSD2825 plus DT bindings
- Support Waveshare DSI2DPI plus DT bindings
gud:
- Fixes
ivpu:
- Fixes
nouveau:
- Use GSP firmware by default
- Fixes
panel:
- panel-edp: Support mt8189 Chromebooks; Support BOE NV140WUM-N64;
Support SHP LQ134Z1; Fixes
- panel-simple: Support Olimex LCD-OLinuXino-5CTS plus DT bindings
- Support Samsung AMS561RA01
- Support Hydis HV101HD1 plus DT bindings
panthor:
- Print task/pid on errors
- Fixes
renesas:
- convert to RUNTIME_PM_OPS
repaper:
- Use shadow-plane helpers
rocket:
- Add driver for Rockchip NPU plus DT bindings
sharp-memory:
- Use shadow-plane helpers
simpledrm:
- Use of_reserved_mem_region_to_resource() helper
tidss:
- Use crtc_ fields for programming display mode
- Remove other drivers from aperture
v3d:
- Support querying nubmer of GPU resets for KHR_robustness
vmwgfx:
- Fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20250814072454.GA18104@linux.fritz.box
Detecting the monitor for DisplayPort targets is more complicated than
just reading the HPD pin level: it requires reading the DPCD in order to
check what kind of device is attached to the port and whether there is
an actual display attached.
In order to let DRM framework handle such configurations, disable
DRM_BRIDGE_OP_DETECT for dp-connector devices, letting the actual DP
driver perform detection. This still keeps DRM_BRIDGE_OP_HPD enabled, so
it is valid for the bridge to report HPD events.
Currently inside the kernel there are only two targets which list
hpd-gpios for dp-connector devices: arm64/qcom/qcs6490-rb3gen2 and
arm64/qcom/sa8295p-adp. Both should be fine with this change.
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konradybcio@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Link: https://lore.kernel.org/r/20250802-dp-conn-no-detect-v1-1-2748c2b946da@oss.qualcomm.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
devm_drm_bridge_alloc() returns ERR_PTR on failure instead of a
NULL pointer, so use IS_ERR() to check the returned pointer.
While at it, on failure, return ERR_CAST(dp) instead of
ERR_PTR(-ENOMEM) in order not to depend on devm_drm_bridge_alloc()
error code implementation.
Fixes: 48f05c3b4b ("drm/bridge: analogix_dp: Use devm_drm_bridge_alloc() API")
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://lore.kernel.org/r/20250806095224.527938-1-victor.liu@nxp.com
The driver currently expects the pixel clock and the HS clock to be
compatible, but the DPHY PLL doesn't give very finely grained rates.
This often leads to the situation where the pipeline just fails, as the
resulting HS clock is just too off.
We could change the driver to do a better job on adjusting the DSI
blanking values, hopefully getting a working pipeline even if the pclk
and HS clocks are not exactly compatible. But that is a bigger work.
What we can do easily is to see in .atomic_check() what HS clock rate we
can get, based on the pixel clock rate, and then convert the HS clock
rate back to pixel clock rate and ask that rate from the crtc. If the
crtc has a good PLL (which is the case for TI K3 SoCs), this will fix
any issues wrt. the clock rates.
If the crtc cannot provide the requested clock, well, we're no worse off
with this patch than what we have at the moment.
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Tested-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20250723-cdns-dsi-impro-v5-14-e61cc06074c2@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
The driver tries to calculate the value for REG_WAKEUP_TIME. However,
the calculation itself is not correct, and to add on it, the resulting
value is almost always larger than the field's size, so the actual
result is more or less random.
According to the docs, figuring out the value for REG_WAKEUP_TIME
requires HW characterization and there's no way to have a generic
algorithm to come up with the value. That doesn't help at all...
However, we know that the value must be smaller than the line time, and,
at least in my understanding, the proper value for it is quite small.
Testing shows that setting it to 1/10 of the line time seems to work
well. All video modes from my HDMI monitor work with this algorithm.
Hopefully we'll get more information on how to calculate the value, and
we can then update this.
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Tested-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20250723-cdns-dsi-impro-v5-11-e61cc06074c2@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
cdns_dsi_adjust_phy_config() is called from cdns_dsi_check_conf(), which
is called from .atomic_check(). It checks the DSI htotal and adjusts it
to align on the DSI lane boundary by changing hfp and then recalculating
htotal and HS clock rate.
This has a few problems.
First is the fact that the whole thing is not needed: we do not need to
align on the lane boundary. The whole frame is sent in HS mode, and it
is fine if the line's last byte clock tick fills, say, only 2 of the 4
lanes. The next line will just continue from there. Assuming the
DSI timing values have been calculated to match the incoming DPI stream,
and the HS clock is compatible with the DPI pixel clock, the "uneven"
DSI lines will even out when multiple lines are being sent.
But we could do the align, aligning is not a problem as such. However,
adding more bytes to the hfp, as the function currently does, makes the
DSI line time longer, so the function then adjusts the HS clock rate.
This is where things fail: we don't know what rates we can get from the
HS clock, and at least in TI K3 SoC case the rates are quite coarsely
grained. Thus small adjustment to hfp will lead to a big change in HS
clock rate, and things break down.
We could do a loop here, adjusting hfp, adjusting clock, checking clock
rate, adjusting hfp again, etc., but considering that the whole
adjustment shouldn't be needed at all, it's easier to just remove the
function.
Something like this function should be added back later, when adding
burst mode support, but that's a bigger change and I don't think this
function would help that work in any way.
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Tested-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20250723-cdns-dsi-impro-v5-9-e61cc06074c2@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
The driver checks if "DPI(HFP) > DSI(HSS+HSA+HSE+HBP)", and rejects the
mode if not.
However, testing shows that this doesn't hold at all. I can set the hfp
to very small values, with no errors. The feedback from the HW team also
was that the check is not right, although it's not clear if there's a
way to validate the FIFO emptying.
The check rejects quite a lot of modes, apparently for no good reason,
so drop the check.
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Tested-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20250723-cdns-dsi-impro-v5-6-e61cc06074c2@ideasonboard.com
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
The conversion of all GPIO drivers to using the .set_rv() and
.set_multiple_rv() callbacks from struct gpio_chip (which - unlike their
predecessors - return an integer and allow the controller drivers to
indicate failures to users) is now complete and the legacy ones have
been removed. Rename the new callbacks back to their original names in
one sweeping change.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Waveshare touchscreen consists of a DPI panel and a driver board.
The waveshare driver board consists of ICN6211 and a MCU to
convert DSI to DPI and control the backlight.
This driver treats the MCU and ICN6211 board as a whole unit.
It can support all resolution waveshare DSI2DPI based panel,
the timing table should come from 'panel-dpi' panel in the device tree.
Signed-off-by: Joseph Guo <qijian.guo@nxp.com>
Suggested-by: Liu Ying <victor.liu@nxp.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250806-waveshare-v3-3-fd28e01f064f@nxp.com
Seems we missed one drm-misc-next pull-request in drm-misc-next-fixes.
This is required to pull in 5d156a9c3d ("drm/bridge: Pass down
connector to drm bridge detect hook") and update its docs.
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
Pull drm updates from Dave Airlie:
"Highlights:
- Intel xe enable Panthor Lake, started adding WildCat Lake
- amdgpu has a bunch of reset improvments along with the usual IP
updates
- msm got VM_BIND support which is important for vulkan sparse memory
- more drm_panic users
- gpusvm common code to handle a bunch of core SVM work outside
drivers.
Detail summary:
Changes outside drm subdirectory:
- 'shrink_shmem_memory()' for better shmem/hibernate interaction
- Rust support infrastructure:
- make ETIMEDOUT available
- add size constants up to SZ_2G
- add DMA coherent allocation bindings
- mtd driver for Intel GPU non-volatile storage
- i2c designware quirk for Intel xe
core:
- atomic helpers: tune enable/disable sequences
- add task info to wedge API
- refactor EDID quirks
- connector: move HDR sink to drm_display_info
- fourcc: half-float and 32-bit float formats
- mode_config: pass format info to simplify
dma-buf:
- heaps: Give CMA heap a stable name
ci:
- add device tree validation and kunit
displayport:
- change AUX DPCD access probe address
- add quirk for DPCD probe
- add panel replay definitions
- backlight control helpers
fbdev:
- make CONFIG_FIRMWARE_EDID available on all arches
fence:
- fix UAF issues
format-helper:
- improve tests
gpusvm:
- introduce devmem only flag for allocation
- add timeslicing support to GPU SVM
ttm:
- improve eviction
sched:
- tracing improvements
- kunit improvements
- memory leak fixes
- reset handling improvements
color mgmt:
- add hardware gamma LUT handling helpers
bridge:
- add destroy hook
- switch to reference counted drm_bridge allocations
- tc358767: convert to devm_drm_bridge_alloc
- improve CEC handling
panel:
- switch to reference counter drm_panel allocations
- fwnode panel lookup
- Huiling hl055fhv028c support
- Raspberry Pi 7" 720x1280 support
- edp: KDC KD116N3730A05, N160JCE-ELL CMN, N116BCJ-EAK
- simple: AUO P238HAN01
- st7701: Winstar wf40eswaa6mnn0
- visionox: rm69299-shift
- Renesas R61307, Renesas R69328 support
- DJN HX83112B
hdmi:
- add CEC handling
- YUV420 output support
xe:
- WildCat Lake support
- Enable PanthorLake by default
- mark BMG as SRIOV capable
- update firmware recommendations
- Expose media OA units
- aux-bux support for non-volatile memory
- MTD intel-dg driver for non-volatile memory
- Expose fan control and voltage regulator in sysfs
- restructure migration for multi-device
- Restore GuC submit UAF fix
- make GEM shrinker drm managed
- SRIOV VF Post-migration recovery of GGTT nodes
- W/A additions/reworks
- Prefetch support for svm ranges
- Don't allocate managed BO for each policy change
- HWMON fixes for BMG
- Create LRC BO without VM
- PCI ID updates
- make SLPC debugfs files optional
- rework eviction rejection of bound external BOs
- consolidate PAT programming logic for pre/post Xe2
- init changes for flicker-free boot
- Enable GuC Dynamic Inhibit Context switch
i915:
- drm_panic support for i915/xe
- initial flip queue off by default for LNL/PNL
- Wildcat Lake Display support
- Support for DSC fractional link bpp
- Support for simultaneous Panel Replay and Adaptive sync
- Support for PTL+ double buffer LUT
- initial PIPEDMC event handling
- drm_panel_follower support
- DPLL interface renames
- allocate struct intel_display dynamically
- flip queue preperation
- abstract DRAM detection better
- avoid GuC scheduling stalls
- remove DG1 force probe requirement
- fix MEI interrupt handler on RT kernels
- use backlight control helpers for eDP
- more shared display code refactoring
amdgpu:
- add userq slot to INFO ioctl
- SR-IOV hibernation support
- Suspend improvements
- Backlight improvements
- Use scaling for non-native eDP modes
- cleaner shader updates for GC 9.x
- Remove fence slab
- SDMA fw checks for userq support
- RAS updates
- DMCUB updates
- DP tunneling fixes
- Display idle D3 support
- Per queue reset improvements
- initial smartmux support
amdkfd:
- enable KFD on loongarch
- mtype fix for ext coherent system memory
radeon:
- CS validation additional GL extensions
- drop console lock during suspend/resume
- bump driver version
msm:
- VM BIND support
- CI: infrastructure updates
- UBWC single source of truth
- decouple GPU and KMS support
- DP: rework I/O accessors
- DPU: SM8750 support
- DSI: SM8750 support
- GPU: X1-45 support and speedbin support for X1-85
- MDSS: SM8750 support
nova:
- register! macro improvements
- DMA object abstraction
- VBIOS parser + fwsec lookup
- sysmem flush page support
- falcon: generic falcon boot code and HAL
- FWSEC-FRTS: fb setup and load/execute
ivpu:
- Add Wildcat Lake support
- Add turbo flag
ast:
- improve hardware generations implementation
imx:
- IMX8qxq Display Controller support
lima:
- Rockchip RK3528 GPU support
nouveau:
- fence handling cleanup
panfrost:
- MT8370 support
- bo labeling
- 64-bit register access
qaic:
- add RAS support
rockchip:
- convert inno_hdmi to a bridge
rz-du:
- add RZ/V2H(P) support
- MIPI-DSI DCS support
sitronix:
- ST7567 support
sun4i:
- add H616 support
tidss:
- add TI AM62L support
- AM65x OLDI bridge support
bochs:
- drm panic support
vkms:
- YUV and R* format support
- use faux device
vmwgfx:
- fence improvements
hyperv:
- move out of simple
- add drm_panic support"
* tag 'drm-next-2025-07-30' of https://gitlab.freedesktop.org/drm/kernel: (1479 commits)
drm/tidss: oldi: convert to devm_drm_bridge_alloc() API
drm/tidss: encoder: convert to devm_drm_bridge_alloc()
drm/amdgpu: move reset support type checks into the caller
drm/amdgpu/sdma7: re-emit unprocessed state on ring reset
drm/amdgpu/sdma6: re-emit unprocessed state on ring reset
drm/amdgpu/sdma5.2: re-emit unprocessed state on ring reset
drm/amdgpu/sdma5: re-emit unprocessed state on ring reset
drm/amdgpu/gfx12: re-emit unprocessed state on ring reset
drm/amdgpu/gfx11: re-emit unprocessed state on ring reset
drm/amdgpu/gfx10: re-emit unprocessed state on ring reset
drm/amdgpu/gfx9.4.3: re-emit unprocessed state on kcq reset
drm/amdgpu/gfx9: re-emit unprocessed state on kcq reset
drm/amdgpu: Add WARN_ON to the resource clear function
drm/amd/pm: Use cached metrics data on SMUv13.0.6
drm/amd/pm: Use cached data for min/max clocks
gpu: nova-core: fix bounds check in PmuLookupTableEntry::new
drm/amdgpu: Replace HQD terminology with slots naming
drm/amdgpu: Add user queue instance count in HW IP info
drm/amd/amdgpu: Add helper functions for isp buffers
drm/amd/amdgpu: Initialize swnode for ISP MFD device
...
drm-misc-fixes for v6.16-rc8/final?:
- Revert all uses of drm_gem_object->dmabuf to
drm_gem_object->import_attach->dmabuf.
- Fix amdgpu returning BIOS cluttered VRAM after resume.
- Scheduler hang fix.
- Revert nouveau ioctl fix as it caused regressions.
- Fix null pointer deref in nouveau.
- Fix unnecessary semicolon in ti_sn_bridge_probe.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://lore.kernel.org/r/72235afd-c849-49fe-9cc1-2b1781abdf08@linux.intel.com
