Extend device tree bindings to support drive strength configuration for the
ksz* switches. Introduced properties:
- microchip,hi-drive-strength-microamp: Controls the drive strength for
high-speed interfaces like GMII/RGMII and more.
- microchip,lo-drive-strength-microamp: Governs the drive strength for
low-speed interfaces such as LEDs, PME_N, and others.
- microchip,io-drive-strength-microamp: Controls the drive strength for
for undocumented Pads on KSZ88xx variants.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz switch driver allows specifying an interrupt line to prevent
having to periodically poll the switch for link ups/downs and other
asynchronous events.
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
SPI and I2C bus node names are expected to be "spi" or "i2c",
respectively, with nothing else, a unit-address, or a '-N' index. A
pattern of 'spi0' or 'i2c0' or similar has crept in. Fix all these
cases. Mostly scripted with the following commands:
git grep -l '\si2c[0-9] {' Documentation/devicetree/ | xargs sed -i -e 's/i2c[0-9] {/i2c {/'
git grep -l '\sspi[0-9] {' Documentation/devicetree/ | xargs sed -i -e 's/spi[0-9] {/spi {/'
With this, a few errors in examples were exposed and fixed.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for the microchip,mcp251xfd.yaml
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for power-supply
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230228215433.3944508-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
DSA switches can fall into one of two categories: switches where all ports
follow standard '(ethernet-)?port' properties, and switches that have
additional properties for the ports.
The scenario where DSA ports are all standardized can be handled by
switches with a reference to the new 'dsa.yaml#/$defs/ethernet-ports'.
The scenario where DSA ports require additional properties can reference
'$dsa.yaml#' directly. This will allow switches to reference these standard
definitions of the DSA switch, but add additional properties under the port
nodes.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Alvin Šipraga <alsi@bang-olufsen.dk> # realtek
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz_switch_chips[] element for KSZ9477 says that port 5 is an xMII
port and it supports speeds of 10/100/1000. The device tree example does
declare a fixed-link at 1000, and RGMII is the only one of those modes
that supports this speed, so use this phy-mode.
The microchip,ksz8565 compatible string is not supported by the
microchip driver, however on Microchip's product page it says that there
are 5 ports, 4 of which have internal PHYs and the 5th is an
MII/RMII/RGMII port. It's a bit strange that this is port@6, but it is
probably just the way it is. Select an RGMII phy-mode for this one as
well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SPI peripheral device bindings need to reference spi-peripheral-props.yaml
in order to use various SPI controller specific properties. Otherwise,
the unevaluatedProperties check will reject any controller specific
properties.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220531220122.2412711-1-robh@kernel.org
Document the new microchip,synclko-disable property which can be
specified to disable the reference clock output from the device if not
required by the board design.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the bindings document for Microchip KSZ Series Ethernet switches
from txt to yaml. Removed spi-cpha and spi-cpol flags is this should be
handled by the device driver.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
