KX022A is a 3-axis Accelerometer from ROHM/Kionix. The sensor features
include variable ODRs, I2C and SPI control, FIFO/LIFO with watermark IRQ,
tap/motion detection, wake-up & back-to-sleep events, four acceleration
ranges (2, 4, 8 and 16g) and probably some other cool features.
Add the basic device tree description for the accelerometer. Only basic
accelerometer features are considered as of now - new properties may or
may not be needed in the future when rest of the features are supported.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/06f8e1ab29d02ed216db10091a269df4b6abad9a.1666614295.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of listing directly properties typical for SPI peripherals,
reference the spi-peripheral-props.yaml schema. This allows using all
properties typical for SPI-connected devices, even these which device
bindings author did not tried yet.
Remove the spi-* properties which now come via spi-peripheral-props.yaml
schema, except for the cases when device schema adds some constraints
like maximum frequency.
While changing additionalProperties->unevaluatedProperties, put it in
typical place, just before example DTS.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220816124321.67817-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADXL367 is an ultralow power, 3-axis MEMS accelerometer.
The ADXL367 does not alias input signals to achieve ultralow power
consumption, it samples the full bandwidth of the sensor at all
data rates. Measurement ranges of +-2g, +-4g, and +-8g are available,
with a resolution of 0.25mg/LSB on the +-2 g range.
In addition to its ultralow power consumption, the ADXL367
has many features to enable true system level power reduction.
It includes a deep multimode output FIFO, a built-in micropower
temperature sensor, and an internal ADC for synchronous conversion
of an additional analog input.
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220214073810.781016-5-cosmin.tanislav@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
BMC156 is very smilar to BMC150, but it has only one accelerometer
interrupt pin. It would make sense if only INT1 was exposed but someone
at Bosch decided to only have an INT2 pin.
In this case, it does not make sense if the first interrupt pin is
treated as INT1 (since that pin does not exist). Add a note to the
bindings that the first interrupt pin is treated as INT2 for BMC156.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210802155657.102766-3-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In Linux the bma180 and bmc150-accel driver cover fairly similar chips
from Bosch (just with minor register differences). For the DT schema,
this does not make any difference: They both represent I2C/SPI devices,
have one or two interrupts plus a vdd/vddio-supply.
This means there is no need to duplicate the schema, we can just
document the compatibles for both drivers in a single DT schema.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210614163150.7774-4-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Bosch accelerometers similar to BMA255 are initially configured to
emit an active-high interrupt signal. This is currently not re-configured
in the bmc150-accel driver so the interrupt should most certainly be
IRQ_TYPE_EDGE_RISING (or potentially IRQ_TYPE_LEVEL_HIGH).
(Unless there is some kind of inverter installed on the board...)
At the moment the bmc150-accel driver forcefully requests the IRQ
using IRQF_TRIGGER_RISING, which means that the IRQ type is currently
ignored in all existing device trees.
Fixes: 6259551cf1 ("iio: accel: bmc150-accel: Add DT bindings")
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210614163150.7774-2-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
BMA253 has two interrupt pins (INT1 and INT2) that can be configured
independently. At the moment the bmc150-accel driver does not make use
of them but it might be able to in the future, so it's useful to already
specify all available interrupts in the device tree.
Set maxItems: 2 for interrupts to allow specifying a second one.
This is necessary as preparation to move the bosch,bma254 compatible
from bosch,bma180.yaml to bosch,bma255.yaml since bma180 allows two
interrupts, but BMA254 is better supported by the bmc150-accel driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210611080903.14384-9-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The KX023-1025 accelerometer uses similar register bits as kxcjk1023,
so it can make use of the same driver. Document the new kionix,kx023-1025
compatible that is also supported by the kxcjk-1013 driver now.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add devicetree binding for the NXP FXLS8962AF/FXLS8964AF
accelerometer sensor.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Binding documentation for this driver was missing.
Note that the binding and some in tree dts files specifiy interrupts
etc but the driver is fairly simple and does not yet make use of them.
Listed both Joachim and myself as maintainers for this binding on basis
it's Joachim's driver but I don't want to volunteer Joachim too
strongly to look after this doc.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Joachim Eastwood <manabian@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210401174112.320497-4-jic23@kernel.org
These two devices have different internal characteristics, but their
external connectivity and as a result device tree descriptions are
identical.
Note that neither driver in Linux currently has an of_match_table
but instead rely on matching via name alone.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210401174112.320497-2-jic23@kernel.org
The bmc150-accel-i2c.c driver has an "_accel" suffix for the
compatibles of BMC150 and BMI055. This is necessary because BMC150
contains both accelerometer (bosch,bmc150_accel) and magnetometer
(bosch,bmc150_magn) and therefore "bosch,bmc150" would be ambiguous.
However, the binding documentation suggests using "bosch,bmc150".
Add the "_accel" suffix for BMC150 and BMI055 so the binding docs
match what is expected by the driver.
Fixes: 6259551cf1 ("iio: accel: bmc150-accel: Add DT bindings")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201202083551.7753-1-stephan@gerhold.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
One question in here is whether we want to constrain the number of
interrupts. Some parts definitely only have 1 such pin, and others
2 pins but I can not find information on the bma254.
Oleksandr's email address is bouncing so I've listed myself as
maintainer for this binding until someone else steps up.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201031184854.745828-41-jic23@kernel.org
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.11 cycle
Usual mixed bag of new drivers / device support + cleanups etc with the
addition of a fairly big set of yaml conversions.
Txt to yaml format conversions.
In some cases dropped separate binding and moved to trivial devices (drop).
Listed by manufacturer
- dht11 temperature(drop)
- adi,ad2s90 adi,ad5272 adi,ad5592r adi,ad5758 adi,ad5933 adi,ad7303
adi,adis16480 adi,adf4350
- ams,as3935
- asahi-kasei,ak8974
- atmel,sama5d2-adc
- avago,apds9300 avago,apds9960
- bosch,bma180 bosch,bmc150_magn bosch,bme680 bosch,bmg180
- brcm,iproc-static-adc
- capella,cm36651
- domintech,dmard06(drop)
- fsl,mag3110 fsl,mma8452 fsl,vf610-dac
- hoperf,hp03
- honeywell,hmc5843
- kionix,kxcjk1013
- maxim,ds1803(drop) maxim,ds4424 maxim,max30100 maxim,max30102
maxim,max31856 maxim,max31855k maxim,max44009
maxim,max5481 maxim,max5821
- meas,htu21(drop) meas,ms5367(drop) meas,ms5611 meas,tsys01(drop)
- mediatek,mt2701-auxadc
- melexis,mlx90614 melexis,mlx90632
- memsic,mmc35240(drop)
- microchip,mcp41010 microchip,mcp4131 microchip,mcp4725
- murata,zap2326
- nxp,fxas21002c nxp,lpc1850-dac
- pni,rm3100
- qcom,pm8018-adc qcom,spmi-iadc
- renesas,isl29501 renesas,rcar-gyroadc
- samsung,sensorhub-rinato
- sensiron,sgp30
- sentech,sx9500
- sharp,gp2ap020a00f
- st,hts221 st,lsm6dsx st,st-sensors(many!) st,uvis25 st,vcl53l0x st,vl6180
- ti,adc084s021 ti,ads124s08
ti,dac5571 ti,dac7311 ti,dac7512 ti,dac7612
ti,hdc1000(drop) ti,palmas-gpadc ti,opt3001 ti,tmp07
- upisemi,us51882
- vishay,vcnl4035
- x-powers,axp209
New device support
* adi,ad5685
- Add support for AD5338R dual output 10-bit DAC
- Add DT-binding doc.
* mediatek,mt6360
- New driver for this SoC ADC with bindings and using new channel label
support in the IIO core.
* st,lsm6dsx
- Add support for LSM6DST
Core:
* Add "label" to device channels, provided via a new core callback. Including
DT docs for when that is the source, and ABI docs.
* Add devm_iio_triggered_buffer_setup_ext to take extra attributes.
* dmaengine, unwrap use of iio_buffer_set_attrs()
* Drop iio_buffer_set_attrs()
* Centralize ioctl call handling. Later fix to ensure -EINVAL returned if
no handler has run.
* Fix an issue with IIO_VAL_FRACTIONAL and negative values - doesn't affect
any known existing drivers, but will impact a future one.
* kernel-doc fix in trigger.h
* file-ops ordering cleanup
Features
* semtech,sx9310
- Add control of hardware gain, proximity thresholds, hysteresis and
debounce.
- Increase what information on hardware configuration can be provided
via DT.
Cleanup and minor features
* adi,ad5685
- Add of_match_table
* adi,ad7292
- Drop pointless spi_set_drvdata() call
* adi,ad7298
- Drop platform data and tidy up external reference config.
* adi,ad7303
- Drop platform data handling as unused.
* adi,ad7768
- Add new label attribute for channels provided from dt.
* adi,ad7887
- devm_ usage in probe simplifying remove and error handling.
* adi,adis16201
- Drop pointless spi_set_drvdata() call
* adi,adis16209
- Drop pointless spi_set_drvdata() call
* adi,adis16240
- White space fixup
* adi,adxl372
- use new devm_iio_triggered-buffer_setup_ext()
* amlogic,meson-saradc
- Drop pointless semicolon.
* amstaos,tsl2563
- Put back i2c_device_id table as needed for greybus probing.
* atmel,at91_adc
- Use of_device_get_match_data() instead of open coding it.
- Constify some driver data
- Add KCONFIG dep on CONFIG_OF and drop of_match_ptr()
- Drop platform data as mostly dead code.
- Tidy up reference voltage logic
* atmel-sama5d2
- Drop a pointless semicolon
- Merge buffer and trigger init into a separate function
- Use new devm_iio_triggered_buff_setup_ext()
* avago,apds9960
- Drop a pointless semicolon
* bosch,bmc150
- Drop a pointless semicolon
- Use new iio_triggered_buffer_setup_ext()
* bosch,bmp280
- Drop a pointless semicolon
* fsl,mma8452
- Constification
* (google),cros_ec
- Use new devm_iio_triggered_buffer_setup_ext()
* hid-sensors
- Use new iio_triggered_buffer_setup_ext()
* ingenic,adc
- Drop a pointless semicolon
* invensense,icm426xx
- Fix MAINTAINERS entry missing :
* mediatek,mt6577_audxac
- Add binding doc for mt8516 compatible with mt8173
* motorola,cpcap-adc
- Fix an implicit fallthrough marking that clang needs to avoid warning.
* samsung,exynos-adc
- Stop relying on users counter form input device in ISR.
* st,lsm6dsx
- add vdd and vddio regulator control (including binding update)
* st,stm32-adc
- Tidy up code for dma transfers.
- Adapt clock duty cycle for proper functioning. Note no known problems
with existing boards.
* st,vl53l0x-i2c
- Put back i2c_device_id table as needed for greybus probing.
* vishay,vcnl4035
- Put back i2c_device_id table as needed for greybus probing.
* tag 'iio-for-5.11a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (126 commits)
dt-bindings:iio:adc:x-powers,axp209-adc: txt to yaml conversion
dt-bindings:iio:adc:renesas,rcar-gyroadc: txt to yaml conversion.
dt-bindings:iio:adc:atmel,sama5d2-adc: txt to yaml conversion
dt-bindings:iio:magnetometer:pni,rm3100: txt to yaml conversion.
dt-bindings:iio:magnetometer:honeywell,hmc5843: txt to yaml format conversion
dt-bindings:iio:magnetometer:bosch,bmc150_magn: txt to yaml conversion.
dt-bindings:iio:magnetometer:asahi-kasei,ak8974: txt to yaml format conversion
dt-bindings:iio:magnetometer:fsl,mag3110: txt to yaml conversion
dt-bindings:iio:light:st,vl6180: txt to yaml format conversion.
dt-bindings:iio:light:vishay,vcnl4035: txt to yaml conversion
dt-bindings:iio:light:st,uvis25: txt to yaml conversion for this UV sensor
dt-bindings:iio:light:upisemi,us51882: txt to yaml conversion.
dt-bindings:iio:light:ti,opt3001: txt to yaml conversion
dt-bindings:iio:light:maxim,max44009: txt to yaml conversion.
dt-bindings:iio:light:sharp,gp2ap020a00f: txt to yaml conversion.
dt-bindings:iio:light:capella,cm36651: txt to yaml conversion.
dt-bindings:iio:light:avago,apds9960: txt to yaml conversion
dt-bindings:iio:light:avago,apds9300: txt to yaml conversion.
dt-bindings:iio:imu:st,lsm6dsx: txt to yaml conversion
dt-bindings:iio:imu:adi,adis16480: txt to yaml conversion
...
In cases where we don't reference another schema, 'additionalProperties'
can be used instead. This is preferred for now as 'unevaluatedProperties'
support isn't implemented yet.
In a few cases, this means adding some missing property definitions of
which most are for SPI bus properties. 'unevaluatedProperties' is not going
to work for the SPI bus properties anyways as they are evaluated from the
parent node, not the SPI child node.
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201005183830.486085-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
This doesn't yet do anything in the tools, but make it explicit so we can
check either 'unevaluatedProperties' or 'additionalProperties' is present
in schemas.
'unevaluatedProperties' is appropriate when including another schema (via
'$ref') and all possible properties and/or child nodes are not
explicitly listed in the schema with the '$ref'.
This is in preparation to add a meta-schema to check for missing
'unevaluatedProperties' or 'additionalProperties'. This has been a
constant source of review issues.
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20201005183830.486085-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Convert and flesh out a bit the binding docs for this simple 3 axis
accelerometer.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Reviewed-by: Matt Ranostay <matt.ranostay@konsulko.com> #for Matt's drivers
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bma180 and related chips should have two regulators attached to
them. The IIO driver currently uses them, document them here as
well.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The bma023, bma150, and smb380 are in the same family as the bma180
and support is being added to the bma180 IIO driver for them.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
