Some sound card setups might require extra pin switches to allow
turning off certain audio components. There are two real examples for
this in smartphones/tablets based on MSM8916:
1. Analog speaker amplifiers connected to headphone outputs.
The MSM8916 analog codec does not have a separate "Line Out" port
so some devices have an analog speaker amplifier connected to one
of the headphone outputs. A pin switch is necessary to allow
playback on headphones without also activating the speaker.
2. External speaker codec also used as earpiece.
Some smartphones have two front-facing (stereo) speakers that can
be also configured to act as an earpiece during voice calls. A pin
switch is needed to allow disabling the second speaker during
voice calls.
There are existing bindings that allow setting up such pin switches in
simple-card.yaml. Document the same for Qcom sound cards.
One variant of example 1 above is added to the examples in the DT
schema: There is an analog speaker amplifier connected to the HPH_R
(right headphone channel) output. Adding a "Speaker" pin switch and
widget allows turning off the speaker when audio should be only played
via the connected headphones.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211214142049.20422-3-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
There are two possible audio setups on MSM8916/APQ8016: Normally the audio
is routed through the audio/modem DSP (covered by the qdsp6 driver). During
upstreaming for the DragonBoard 410c it was decided to bypass it and
instead talk directly to the audio controller using the "lpass" driver.
Bypassing the DSP gives more control about the audio configuration but limits
the functionality: For example, routing audio through the audio/modem DSP is
strictly required for voice call audio. Also, without the special changes in
the DB410c firmware other MSM8916 devices can only use the bypass as long as
the modem DSP is not started. Otherwise, the firmware will assume control of
the LPASS hardware block and audio is no longer functional.
Add support for using the DSP audio setup instead using a new
"qcom,msm8916-qdsp6-sndcard" compatible. It is basically a mixture of
the apq8016-sbc-sndcard and the newer sm8250-sndcard, which uses
indirect QDSP6 DAI links instead of the direct LPASS DAI links.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211202145505.58852-5-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
All the Qualcomm sound card drivers use the same common device tree
parsing code, so the allowed device tree nodes are almost the same
for all of them. Convert the qcom,apq8016-sbc-sndcard documentation
to a DT schema by adding it to the existing qcom,sm8250 schema.
The only speciality of qcom,apq8016-sbc-sndcard is that it has memory
resources for setting up an I/O mux. This can be handled using
a conditional if statement that only requires it for the apq8016-sbc
compatible.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211202145505.58852-4-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The sm8250 audio driver uses the common Qualcomm device tree parser and
therefore already supports the "aux-devs" property that allows adding
additional auxiliary devices to the sound card (e.g. analog speaker
amplifiers that can be connected using "audio-routing").
Document the property in the DT schema for sm8250 as well. The description
is taken from simple-card.yaml which has a very similar property.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211202145505.58852-3-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The MultiMedia audio routes can be deduced from other parts of the
device tree (e.g. the definitions of the MultiMedia DAIs) and therefore
specifying them again in "audio-routing" is redundant and prone to
mistakes. This is no longer necessary since commit 6fd8d2d275
("ASoC: qcom: qdsp6: Move frontend AIFs to q6asm-dai").
Let's drop them from the example in the DT schema as well
to avoid confusion.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211202145505.58852-2-stephan@gerhold.net
Signed-off-by: Mark Brown <broonie@kernel.org>
