SPI NOR flashes have specific cs-setup time requirements without which
they can't work at frequencies close to their maximum supported frequency,
as they miss the first bits of the instruction command. Unrecognized
commands are ignored, thus the flash will be unresponsive. Introduce the
spi-cs-setup-ns property to allow spi devices to specify their cs setup
time.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-2-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-3wire property is device specific and should be accepted only if
device really needs them. Drop it from common spi-peripheral-props.yaml
schema, mention in few panel drivers which use it and include instead in
the SPI controller bindings. The controller bindings will provide
spi-3wire type validation and one place for description. Each device
schema must list the property if it is applicable.
The Samsung S6E63M0 panel uses also spi-cpha/cpol properties on at least
one board (ste-ux500-samsung-janice/dts), so add also these to the
panel's bindings.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220810131311.428645-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-cpha and spi-cpol properties are device specific and should be
accepted only if device really needs them. Drop them from common
spi-peripheral-props.yaml schema, mention in few panel drivers which use
them and include instead in the SPI controller bindings. The controller
bindings will provide CPHA/CPOL type validation and one place for
description. Each device schema must list the properties if they are
applicable.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220722191539.90641-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI bus per device properties must be defined in spi-peripheral-props.yaml
for unevaluatedProperties checks to work correctly on device nodes.
This has the side effect of promoting 'rx-sample-delay-ns' to be a
common property, but functionally it's no different if it was defined in
a Synopsys specific schema file.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220525210053.2488756-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Alim Akhtar:
This series adds support for the SPI controller in the Tesla FSD SoC,
also pulling in:
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd.git ib-mfd-spi-dt-v5.18
from the MFD tree which has dependencies for the DT bindings.
The spi-peripheral-props.yaml schema contains peripheral-specific
properties for SPI controllers that should be present in the peripheral
node. Move peripheral-specific properties to a separate file and refer
to it in spi-peripheral-props.yaml.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211109181911.2251-3-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Many SPI controllers need to add properties to peripheral devices. This
could be the delay in clock or data lines, etc. These properties are
controller specific but need to be defined in the peripheral node
because they are per-peripheral and there can be multiple peripherals
attached to a controller.
If these properties are not added to the peripheral binding, then the
dtbs check emits a warning. But these properties do not make much sense
in the peripheral binding because they are controller-specific and they
will just pollute every peripheral binding. So this binding is added to
collect all such properties from all such controllers. Peripheral
bindings should simply refer to this binding and they should be rid of
the warnings.
There are some limitations with this approach. Firstly, there is no way
to specify required properties. The schema contains properties for all
controllers and there is no way to know which controller is being used.
Secondly, there is no way to restrict additional properties. Since this
schema will be used with an allOf operator, additionalProperties needs
to be true. In addition, the peripheral schema will have to set
unevaluatedProperties: false.
Despite these limitations, this appears to be the best solution to this
problem that doesn't involve modifying existing tools or schema specs.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211109181911.2251-2-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
