DCN31 supports FAMS, but this was not correctly set to the hardware
setup sequence. This commit fixes this issue by setting the MCLK switch
capability based on the feature capability retrieved from the DMUB.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently driver enables dmub outbox notification before oubox ISR is
registered. During boot scenario, sometimes dmub issues hpd outbox
message before driver registers ISR and those messages are missed.
[How]
Enable dmub outbox notification after outbox ISR is registered. Also,
restructured outbox enable code to call from dm layer and renamed APIs.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Consolidate dmub access to a single interface. This makes it easier to
add code in the future that needs to run every time a dmub command is
requested (e.g. instrumentation, locking etc).
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Observing underflow on dcn30+ system config at 4k144hz
[How]
We set the UCLK hardmax on AC/DC switch if softmax is enabled
and also on boot. While booting up the UCLK Hardmax is set
to softmax before the init sequence and the init sequence
resets the hardmax to UCLK max which enables P-state switching.
Just added a conditional check to avoid setting hardmax on init.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Ayush Gupta <ayugupta@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
All dc subcomponents should call another dc component via function pointers
stored in a component structure. This is part of dc coding convention since
the beginning. The reason behind this is to improve encapsulation and
polymorphism. The function contract is extracted into a single link service
structure defined in link.h header file and implemented only in link_factory.c instead
of spreading across multiple files in link component file structure.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc_link contains over 30k line of code, the decision is to break it
down to files residing in link folder based on functionality. This
change is the last break down change which will remove dc_link.c
file after everything is broken down.
[how]
Move remaining dc_link.c functions into link_detection, link_dpms,
link_validation, link_resource, and link_fpga and remove dc_link.
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Temporarly merge dc_link_dp functions into dc_link for the
purpose of removing dc_link_dp files. This is a transitional
change for later commits where we will further refactor dc_link
file.
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Original change 594b237b9a ("drm/amd/display: Add
interface to track PHY state") was implemented by assuming stream's
dpms off is equivalent to PHY power off.
This assumption doesn't hold in following situations:
1. MST multiple stream scenario, where multiple streams are sharing the
same PHY output. Toggle dpms off for one of the stream doesn't power
off the PHY due to the presence of other streams.
2. enable stream failure scenario, where enable stream fails due to
failure of link training. This will cause DPMS off is set to false, while
the actual PHY power state is off in certain cases.
Due to the problematic assumption, the logic will skip disabling
other streams for MST multiple stream scenario, therefore PHY is
not actually powered off.
[how]
1. Rework this refactor by moving PHY state update down to hardware
level, where we update PHY state in place when hardware sequencer
is actually changing the power state of the PHY hardware.
2. Reimplement symclk on TX off workaround in place when we are actually
calling transmitter control to power off PHY in dcn32. Note the workaround is
added due to the lack of proper software interface to set TX while keeping
symclk on. We plan to address this interface problem so we can set TX off
only without affecting symclk in future dcn versions.
Fixes: 594b237b9a ("drm/amd/display: Add interface to track PHY state")
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some scenarios it is possible for the encoder assignment module to be
set to "transient" mode even though there are no new encoder
assignments.
This can lead to incorrect results when querying encoder assignment,
which in turn can cause incorrect displays to be manipulated.
[How]
Only allow encoder assignment to be in transient mode of operation when
there are valid new encoder assignments.
Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For panels with pixel clock > 1200MHz that require ODM
in pre-OS, when driver is disabled in OS, odm is enabled.
Upon driver enablement, corruption is seen if
odm was originally enabled. DP_PIXEL_COMBINE and
pixelclk must be programmed prior to programming the
optc-odm registers. However, eDP displays aren't blanked
prior to initializing odm in this case.
[How]
Upon driver enablement, check whether odm is enabled,
if so, blank eDP prior to programming optc-odm
registers.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In init_hw() we call init_pipes() before enabling power gating.
init_pipes() tries to power gate dsc but it may fail because
required force-ons are not released yet.
As a result with dsc config the following errors observed on resume:
"REG_WAIT timeout 1us * 1000 tries - dcn20_dsc_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_dpp_pg_control"
"REG_WAIT timeout 1us * 1000 tries - dcn20_hubp_pg_control"
[How]
Move enable_power_gating_plane() before init_pipes() in init_hw()
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
display mapping change will involved pipe power gating on and off.
when doing this too fase, sometimes usbc will have no display.
check HW status, it is still in pipe power gating.
[how]
insert polling HW status to make sure the required state reached.
also add dal registry key handling.
Reviewed-by: Sung joon Kim <Sungjoon.Kim@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently driver enables dmub outbox notification before oubox ISR is
registered. During boot scenario, sometimes dmub issues hpd outbox
message before driver registers ISR and those messages are missed.
[How]
Enable dmub outbox notification after outbox ISR is registered. Also,
restructured outbox enable code to call from dm layer and renamed APIs.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
- We only ever want seamless boots on eDPs
- The naming and logic did not match the context
[HOW]
- Removed unnecessary if statements
- Renamed power_down_display_on_boot to seamless_boot_edp_requested and
swapped the logic
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jarif Aftab <jaraftab@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Due to pass the wrong parameter down to the enable_stream_gating(),
it would cause the DSC of the removing stream would not be PG.
[HOW]
To pass the correct parameter down th the enable_stream_gating().
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
After unloading driver, driver would not disable DSC function.
At next loading driver, driver would power all DSC engines off.
When driver powered the active DSC off, the screen would be gray
until reprograming DSC relatived register correcntly.
[HOW]
1. Remove DSC Power down code into init_pipes()
2. Depend on the OTG mapping information and DSC status to skip
power off for the working DSC.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
1. The code to blank all dp display have been called many times,
so add helpers in dc_link to make it more concise.
2. Add some check to fix the dmesg errors at boot and resume from S3
on dcn3.1 during DQE's promotion test.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPO is only used for DP2.0. HPO HW control should be
disable when not being used to save power.
[How]
Shutdown HPO HW control during init hw.
Shutdown HPO HW control during stream disable.
Enable HPO HW control during stream enable if DP2.0.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
i2c memory doesn't get set to light sleep on hw init as intended
[HOW]
Set i2c to light sleep after reg gets zeroed, ensuring memory power
control doesn't get disabled for any other DIO memory
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 1445d967fb.
This patch introduced a couple of dmesg warnings, this is not a valid
approach anymore. For this reason, we are reverting this patch, and we
need to revert the workaround patch.
v2: squash in unused variable removal (Alex)
Cc: Hanghong Ma <hanghong.ma@amd.com>
Cc: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To enable dc links for USB4 DPIA ports and AUX command tunneling
for YELLOW_CARP_B0.
[HOW]
1) Created dc links for all USB4 DPIA ports in create_links().
dc_link_construct() implementation is split for legacy DDC and DPIAs.
As usb4 has no ddc, ddc->ddc_pin will be set to NULL for its dc link
and this parameter will be used to identify the dc links as DPIA. The
dc link for DPIA is further to be enhanced with implementation for link
encoder and link initialization.
2) usb4_dpia_count in struct resource_pool will be initialized to 4 in
dcn31_resource_construct() if the DCN is YELLOW_CARP_B0.
3) Enabled DMUB AUX via outbox for YELLOW_CARP_B0.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The codes to blank all dp display have been called many times,
so add a helper in dc_link to make it more concise.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Incorrect encoder assignments were being used while applying a new state
to hardware.
(1) When committing a new state to hardware requires resetting the
back-end, the encoder assignments of the current or old state should be
used when disabling the back-end; and the encoder assignments for the
next or new state should be used when re-enabling the back-end.
(2) Link training on hot plug could take over an encoder already in use
by another stream without first disabling it.
[How]
(1) Introduce a resource context 'link_enc_cfg_context' which includes:
- a mode to indicate when transitioning from current to next state.
- transient encoder assignments to use during this state transition.
Update the encoder configuration interface to respond to queries about
encoder assignment based on the mode of operation.
(2) Check if an encoder is already in use before attempting to perform
link training on hot plug.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When system is in Z10 HPD interrupts cannot fire, we may miss display
configuration changes.
[How]
When Zstate is enabled, if DMUB indicate DCN has lost power, do a
complete detection periodically.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Assuming DIG link encoders are statically mapped to links can cause
system instability due to null pointer accesses.
[How]
- Add checks for non-null link encoder pointers before trying to access
them.
- When a hardware platform uses dynamic DIG assignment (i.e. resource
function 'link_encs_assign' defined) and a link supports flexible
mapping to DIGs, use the link_enc_cfg API to access the DIG assigned to
a link or stream.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When ODM is enabled, ABM is blocked on dcn31 but unblocked on dcn30.
Since the dcn31 firmware is now able to handle ABM interop with ODM, it
is no longer necessary to block ABM when ODM is enabled.
Since the dcn30 firmware does not handle ABM interop with ODM, leaving
that combination unblocked can lead to one side of the screen appearing
brighter than the other.
[How]
When ODM is enabled, unblock abm on dcn31 and block it on dcn30
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DM initializes VM context after DMCUB initialization.
This results in loss of DCN_VM_CONTEXT registers after z10.
[How]
Notify DMCUB when VM setup is complete, and have DMCUB
save init registers.
v2: squash in CONFIG_DRM_AMD_DC_DCN3_1 fix
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During headless boot, DIG may be on which causes HW/SW discrepancies.
To avoid this we power down hardware on boot if DIG is turned on. With
introduction of multiple eDP, hardware power down is being bypassed
under certain conditions.
[How]
Fixed hardware power down bypass, and ensured hardware will power down
if DIG is on and seamless boot is not enabled.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
