- Reverts "drm/amd/display: Revert HUBP blank behaviour for now"
- Hubp blank will fail if the pipe is locked (this is the case on
linux), so add a check to make sure pipe isn't locked, if it is then
defer the blank to post_unlock.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN30 has a bug where blanking HUBP blocks pstate allow unless
HUBP_DISABLE is toggled afterwards.
[HOW]
Create a HW sequence for blanking HUBP.
1. Wait for enter VBLANK
2. Set HUBP_BLANK
3. Make sure HUBP_IN_BLANK = 1
4. Toggle HUBP_DISABLE on and off to perform soft reset
All existing calls to hubp->funcs->set_blank should be replaced with
this new sequence.
In wait_for_mpcc_disconnect, only blank the pipe being disconnected, and
leave all other pipes unmodified.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Seamless boot stream has hw resource assigned, already. 'add' is
actually rebuild the assignment.
[How]
Swap seamless boot stream to pipe 0 (if needed) to ensure pipe_ctx
matches
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Raymond Yang <rayyang@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When OS reboots, and panel is turned off, T12 may not be maintained.
T12 is defined as the interval between VDDC off (occurs at shutdown) and
the next VDDC on (occurs when eDP is POST-ed)
[how]
DC already tracks panel power off time. Add a DC interface which DM can
call during shutdown. Ideally this should be as late as possible during
the shutdown sequence so the extra delay is minimal.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. the corrected timing to write DPCD 300h AMD signature is before
link training.
2. and VBIOS will writes correctted AMD signature by after AGESA 1.0.0,
so driver doesn't need to write DPCD 300h again to switch config.
3. there are some OLED panel will clean backlight level to 0 once
receive DPCD 300h, so we will see flicker issue at that time.
[How]
read DPCD 300h signature before write it to avoid reprogram again, if
AMD signature was writed corrected by VBIOS, driver will not reprogram
it again.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Yu-ting Shen <Yu-ting.Shen@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When switching single pipe to split pipe, the bandwidth check is just
for first pipe. The 2nd pipe with abnormal(or zero) dpp clock when pipe
ready and unlock leads the garbage on display.
[How]
Removed external increasing dpp clock check, the internal function
already loops all of pipes to check whether update dpp clock.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DCN10 uses plane visibility to determine when to unblank HUBP; there is
no reason DCN20+ should not do the same.
[HOW]
In addition to changing the check in HWSEQ, we must change
is_pipe_tree_visible so that it checks ODM pipe topologies as well as
MPC. Since we're now checking both ODM and MPC topologies, the helper
function names have been changed to reference "parent" and "child"
instead of "top" and "bottom".
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:38: warning: Function parameter or member 'raw_state' not described in 'convert_psr_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:81: warning: Function parameter or member 'dmub' not described in 'dmub_psr_get_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:81: warning: Function parameter or member 'state' not described in 'dmub_psr_get_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:97: warning: Function parameter or member 'dmub' not described in 'dmub_psr_set_version'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:97: warning: Function parameter or member 'stream' not described in 'dmub_psr_set_version'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:128: warning: Function parameter or member 'dmub' not described in 'dmub_psr_enable'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:128: warning: Function parameter or member 'enable' not described in 'dmub_psr_enable'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:128: warning: Function parameter or member 'wait' not described in 'dmub_psr_enable'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:177: warning: Function parameter or member 'dmub' not described in 'dmub_psr_set_level'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:177: warning: Function parameter or member 'psr_level' not described in 'dmub_psr_set_level'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:203: warning: Function parameter or member 'dmub' not described in 'dmub_psr_copy_settings'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:203: warning: Function parameter or member 'link' not described in 'dmub_psr_copy_settings'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:203: warning: Function parameter or member 'psr_context' not described in 'dmub_psr_copy_settings'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:284: warning: Function parameter or member 'dmub' not described in 'dmub_psr_force_static'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:301: warning: Function parameter or member 'dmub' not described in 'dmub_psr_get_residency'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:301: warning: Function parameter or member 'residency' not described in 'dmub_psr_get_residency'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:323: warning: Function parameter or member 'psr' not described in 'dmub_psr_construct'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:323: warning: Function parameter or member 'ctx' not described in 'dmub_psr_construct'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:332: warning: Function parameter or member 'ctx' not described in 'dmub_psr_create'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dmub_psr.c:349: warning: Function parameter or member 'dmub' not described in 'dmub_psr_destroy'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Wyatt Wood <wyatt.wood@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_sw.c:342:6: warning: no previous prototype for ‘dce_i2c_sw_engine_set_speed’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_sw.c:356:6: warning: no previous prototype for ‘dce_i2c_sw_engine_acquire_engine’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_sw.c:400:6: warning: no previous prototype for ‘dce_i2c_sw_engine_submit_channel_request’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_i2c_sw.c:443:6: warning: no previous prototype for ‘dce_i2c_sw_engine_submit_payload’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:427:6: warning: no previous prototype for ‘dce60_opp_set_clamping’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:548:6: warning: no previous prototype for ‘dce60_opp_program_bit_depth_reduction’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:571:6: warning: no previous prototype for ‘dce60_opp_program_clamping_and_pixel_encoding’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_opp.c:681:6: warning: no previous prototype for ‘dce60_opp_program_fmt’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
And only declare it if it's to be used.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_dmcu.h:320:23: warning: ‘abm_gain_stepsize’ defined but not used [-Wunused-const-variable=]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c: In function ‘dce60_transform_set_scaler’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c:496:7: warning: variable ‘filter_updated’ set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c: In function ‘dce60_transform_set_pixel_storage_depth’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c:1040:19: warning: variable ‘expan_mode’ set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_transform.c:1040:6: warning: variable ‘pixel_depth’ set but not used [-Wunused-but-set-variable]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Demote the one that provides no param descriptions.
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'calc_pll_cs' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'target_pix_clk_100hz' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'ref_divider' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'post_divider' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'feedback_divider_param' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:142: warning: Function parameter or member 'fract_feedback_divider_param' not described in 'calculate_fb_and_fractional_fb_divider'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:200: warning: Function parameter or member 'calc_pll_cs' not described in 'calc_fb_divider_checking_tolerance'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:200: warning: Function parameter or member 'pll_settings' not described in 'calc_fb_divider_checking_tolerance'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:200: warning: Function parameter or member 'ref_divider' not described in 'calc_fb_divider_checking_tolerance'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:200: warning: Function parameter or member 'post_divider' not described in 'calc_fb_divider_checking_tolerance'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:200: warning: Function parameter or member 'tolerance' not described in 'calc_fb_divider_checking_tolerance'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:478: warning: Function parameter or member 'clk_src' not described in 'dce110_get_pix_clk_dividers_helper'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:478: warning: Function parameter or member 'pll_settings' not described in 'dce110_get_pix_clk_dividers_helper'
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_clock_source.c:478: warning: Function parameter or member 'pix_clk_params' not described in 'dce110_get_pix_clk_dividers_helper'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_link_encoder.c:1200:6: warning: no previous prototype for ‘dce60_link_encoder_enable_dp_output’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_link_encoder.c:1239:6: warning: no previous prototype for ‘dce60_link_encoder_enable_dp_mst_output’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_link_encoder.c:1429:6: warning: no previous prototype for ‘dce60_link_encoder_dp_set_phy_pattern’ [-Wmissing-prototypes]
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Mauro Rossi <issor.oruam@gmail.com>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:501: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:501: warning: Function parameter or member 'gpio_id' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:501: warning: Function parameter or member 'info' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:815: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:815: warning: Function parameter or member 'signal' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:815: warning: Function parameter or member 'index' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:815: warning: Function parameter or member 'ss_info' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:1210: warning: Function parameter or member 'dcb' not described in 'bios_parser_set_scratch_critical_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser2.c:1210: warning: Function parameter or member 'state' not described in 'bios_parser_set_scratch_critical_state'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2588:16: warning: no previous prototype for ‘update_slot_layout_info’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2692:16: warning: no previous prototype for ‘get_bracket_layout_record’ [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:925: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:925: warning: Function parameter or member 'signal' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:925: warning: Function parameter or member 'index' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:925: warning: Function parameter or member 'ss_info' not described in 'bios_parser_get_spread_spectrum_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:997: warning: Function parameter or member 'bp' not described in 'get_ss_info_from_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:997: warning: Function parameter or member 'id' not described in 'get_ss_info_from_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:997: warning: Function parameter or member 'ss_info' not described in 'get_ss_info_from_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1022: warning: Function parameter or member 'bp' not described in 'get_ss_info_from_internal_ss_info_tbl_V2_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1022: warning: Function parameter or member 'id' not described in 'get_ss_info_from_internal_ss_info_tbl_V2_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1022: warning: Function parameter or member 'info' not described in 'get_ss_info_from_internal_ss_info_tbl_V2_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1087: warning: Function parameter or member 'bp' not described in 'get_ss_info_from_ss_info_table'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1087: warning: Function parameter or member 'id' not described in 'get_ss_info_from_ss_info_table'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1087: warning: Function parameter or member 'ss_info' not described in 'get_ss_info_from_ss_info_table'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1469: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_encoder_cap_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1469: warning: Function parameter or member 'object_id' not described in 'bios_parser_get_encoder_cap_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1469: warning: Function parameter or member 'info' not described in 'bios_parser_get_encoder_cap_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1508: warning: Function parameter or member 'bp' not described in 'get_encoder_cap_record'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1508: warning: Function parameter or member 'object' not described in 'get_encoder_cap_record'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1566: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_ss_entry_number'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1566: warning: Function parameter or member 'signal' not described in 'bios_parser_get_ss_entry_number'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1619: warning: Function parameter or member 'bp' not described in 'get_ss_entry_number_from_ss_info_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1619: warning: Function parameter or member 'id' not described in 'get_ss_entry_number_from_ss_info_tbl'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1686: warning: Function parameter or member 'bp' not described in 'get_ss_entry_number'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1686: warning: Function parameter or member 'id' not described in 'get_ss_entry_number'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1705: warning: Function parameter or member 'bp' not described in 'get_ss_entry_number_from_internal_ss_info_tbl_v2_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1705: warning: Function parameter or member 'id' not described in 'get_ss_entry_number_from_internal_ss_info_tbl_v2_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1740: warning: Function parameter or member 'bp' not described in 'get_ss_entry_number_from_internal_ss_info_tbl_V3_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1740: warning: Function parameter or member 'id' not described in 'get_ss_entry_number_from_internal_ss_info_tbl_V3_1'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1783: warning: Function parameter or member 'dcb' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1783: warning: Function parameter or member 'gpio_id' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:1783: warning: Function parameter or member 'info' not described in 'bios_parser_get_gpio_pin_info'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2211: warning: Function parameter or member 'dcb' not described in 'bios_parser_set_scratch_critical_state'
drivers/gpu/drm/amd/amdgpu/../display/dc/bios/bios_parser.c:2211: warning: Function parameter or member 'state' not described in 'bios_parser_set_scratch_critical_state'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/conversion.c:86: warning: Function parameter or member 'matrix' not described in 'convert_float_matrix'
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/conversion.c:86: warning: Function parameter or member 'flt' not described in 'convert_float_matrix'
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/conversion.c:86: warning: Function parameter or member 'buffer_size' not described in 'convert_float_matrix'
drivers/gpu/drm/amd/amdgpu/../display/dc/basics/conversion.c:86: warning: Excess function parameter 'param' description in 'convert_float_matrix'
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: amd-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
From Ard:
"Simply disabling -mgeneral-regs-only left and right is risky, given that
the standard AArch64 ABI permits the use of FP/SIMD registers anywhere,
and GCC is known to use SIMD registers for spilling, and may invent
other uses of the FP/SIMD register file that have nothing to do with the
floating point code in question. Note that putting kernel_neon_begin()
and kernel_neon_end() around the code that does use FP is not sufficient
here, the problem is in all the other code that may be emitted with
references to SIMD registers in it.
So the only way to do this properly is to put all floating point code in
a separate compilation unit, and only compile that unit with
-mgeneral-regs-only."
Disable support until the code can be properly refactored to support this
properly on aarch64.
Acked-by: Will Deacon <will@kernel.org>
Reported-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hw supports fp16, this is not only useful for HDR,
but also for standard dynamic range displays, because
it allows to get more precise color reproduction with
about 11 - 12 bpc linear precision in the unorm range
0.0 - 1.0.
Working fp16 scanout+display (and HDR over HDMI) was
verified on a DCE-8 asic, so i assume that the more
recent DCE-10/11 will work equally well, now that
format-specific plane scaling constraints are properly
enforced, e.g., the inability of fp16 to scale on older
hw like DCE-8 to DCE-11.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
- use dc interface instead of hwss interface in cursor functions, to keep
dc->idle_optimizations_allowed updated
- add dc interface to check if idle optimizations might apply to a plane
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following coccinelle report:
drivers/gpu/drm/amd/display/dc/dcn302/dcn302_resource.c:1357:6-8:
WARNING: possible condition with no effect (if == else)
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adjust a jump target so that a bit of exception handling can be better
reused at the end of this function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* Return directly after a call of the function “kzalloc” failed
at the beginning.
* Delete a label which became unnecessary with this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We defer clock updates to after pipes have been programmed. In
some instances we use DPPCLK that have been previously set to be
"unused". This results in a brief window of time where underflow
could occur.
[How]
During prepare bandwidth allow rn_update_clocks_update_dpp_dto
to check each instance and compare previous clock to new clock.
If new clock is higher than previous clock, program DPPDTO.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For certain timings, Renoir may underflow due to sr exit latency
being too slow.
[How]
Updated wm table for renoir.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DSC should only be acquired per OPP. Therefore, DSC should only
be acquired for the top_pipe when ODM is enabled.
Not doing this check may lead to acquiring more DSC's than needed
when doing MPO + ODM Combine.
[HOW]
Only acquire DSC if pipe is top_pipe.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
FP2 programming not happening when topology changes occur with multiple
displays.
[How]
Ensure FP2 is programmed whenever global sync changes occur but wait for
VACTIVE first to avoid underflow.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
