There are cases, where devices have an HDMI1.4 retimer, and TMDS clock rate
is capped to 340MHz via VBT. In such cases scrambling might be supported
by the platform and an HDMI2.0 sink for lower TMDS rates, but not
supported by the retimer, causing blankouts.
So avoid enabling scrambling, if the TMDS clock is capped to <= 340MHz.
v2: Added comment, documenting the rationale to check for TMDS clock,
before going for scrambling. (Arun)
v3: Fixed the function name to check if source supports scrambling. (Jani)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221222040851.3029514-1-ankit.k.nautiyal@intel.com
Current implementation of async flip w/a relies on assumption that
previous atomic commit contains valid information if async_flip is still
enabled on the plane. It is incorrect. If previous commit did not modify
the plane its state->uapi.async_flip can be false. As a result DMAR/PIPE
errors can be observed:
i915 0000:00:02.0: [drm] *ERROR* Fault errors on pipe A: 0x00000080
i915 0000:00:02.0: [drm] *ERROR* Fault errors on pipe A: 0x00000080
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read NO_PASID] Request device [00:02.0] fault addr 0x0 [fault reason 0x06] PTE Read access is not set
v2: update async_flip_planes in more reliable places (Ville)
v3: reset async_flip_planes and do_async_flip in more scenarios (Ville)
v4: move all resets to plane loops (Ville)
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127153003.2225111-1-andrzej.hajda@intel.com
SEL_FETCH_CTL registers are armed immediately when plane is disabled.
SEL_FETCH_* instances of plane configuration are used when doing
selective update and normal plane register instances for full updates.
Currently all SEL_FETCH_* registers are written as a part of noarm
plane configuration. If noarm and arm plane configuration are not
happening within same vblank we may end up having plane as a part of
selective update before it's PLANE_SURF register is written.
Fix this by splitting plane selective fetch configuration into arm and
noarm versions and call them accordingly. Write SEL_FETCH_CTL in arm
version.
v3:
- add arm suffix into intel_psr2_disable_plane_sel_fetch
v2:
- drop color_plane parameter from arm part
- dev_priv -> i915 in arm part
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Vinod Govindapillai <vinod.govindapillai@intel.com>
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230130080651.3796929-1-jouni.hogander@intel.com
drm/i915 feature pull #2 v6.3:
Features and functionality:
- Enable HF-EEODB by switching HDMI, DP and LVDS to use struct drm_edid (Jani)
- Start using unversioned DMC firmware paths for new platforms (Gustavo)
Refactoring and cleanups:
- ELD refactor: Stop using hardware buffer, precompute ELD, and wire up ELD in
the state checker (Ville)
- Use generics for debugfs device parameters (Jani)
- DSB refactoring and fixes (Ville)
- Header refactoring, add new intel_display_limits.h (Jani)
- Split out GMCH code to a new file (Jani)
- Split out vblank code to a new file (Jani)
- i915_drv.h and struct drm_i915_private cleanups (Jani)
- Simplify FBC and DRRS debug attributes (Deepak R Varma)
- Remove some single-use macros (Rodrigo)
Fixes:
- Fix scaler limits for display versions 12 and 13 (Luca)
- Fix plane source size check for zero height (Drew Davenport)
- Implement PSR2 selective fetch workaround (Jouni)
- Expand a PSR workaound to more platforms and pipes (Jouni)
- Expand an HDMI infoframe workaround to all MTL steppings (Jouni)
- Enable PIPEDMC whenever its corresponding pipe is enabled (Imre)
Merges:
- Backmerge drm-next (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87tu0c44gv.fsf@intel.com
Avoid the array lookup, converting the PLL macros after ICL to
_PICK_EVEN_RANGES. This provides the following reduction in code size:
$ size build64/drivers/gpu/drm/i915/i915.o{.old,.new}
text data bss dec hex filename
4027456 185703 6984 4220143 4064ef build64/drivers/gpu/drm/i915/i915.o.old
4026997 185703 6984 4219684 406324 build64/drivers/gpu/drm/i915/i915.o.new
At the same time it's safer, avoiding out-of-bounds array access. This
allows to remove _MMIO_PLL3() that is now unused.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230120193457.3295977-4-lucas.demarchi@intel.com
Convert all the connectors that use cached connector edid and
detect_edid to drm_edid.
Since drm_get_edid() calls drm_connector_update_edid_property() while
drm_edid_read*() do not, we need to call drm_edid_connector_update()
separately, in part due to the EDID caching behaviour in HDMI and
DP. Especially DP depends on the details parsed from EDID. (The big
behavioural change conflating EDID reading with parsing and property
update was done in commit 5186421cbf ("drm: Introduce epoch counter to
drm_connector"))
v6: Rebase on drm_edid_connector_add_modes()
v5: Fix potential uninitialized var use (kernel test robot <lkp@intel.com>)
v4: Call drm_edid_connector_update() after reading HDMI/DP EDID
v3: Don't leak vga switcheroo EDID in LVDS init (Ville)
v2: Don't leak opregion fallback EDID (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/eabb4de932841b38b34cc2818ea9fbf7c10224fd.1674643465.git.jani.nikula@intel.com
Initialize the fb-helper's preferred_bpp field early from within
drm_fb_helper_prepare(); instead of the later client hot-plugging
callback. This simplifies the generic fbdev setup function.
No real changes, but all drivers' fbdev code has to be adapted.
v3:
* build with CONFIG_DRM_FBDEV_EMULATION unset (kernel test bot)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230125200415.14123-7-tzimmermann@suse.de
Move a handful of key enums to a new file intel_display_limits.h. These
are the enum types, and the MAX/NUM enumerations within them, that are
used in other headers. Otherwise, there's no common theme between them.
Replace intel_display.h include with intel_display_limit.h where
relevant, and add the intel_display.h include directly in the .c files
where needed.
Since intel_display.h is used almost everywhere in display/, include it
from intel_display_types.h to avoid massive changes across the
board. There are very few files that would need intel_display_types.h
but not intel_display.h so this is neglible, and further cleanup between
these headers can be left for the future.
Overall this change drops the direct and indirect dependencies on
intel_display.h from about 300 to about 100 compilation units, because
we can drop the include from i915_drv.h.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230116164644.1752009-1-jani.nikula@intel.com
Since we use the audio component to transfer the ELD to the audio
driver on hsw+ platforms there is no point in even programming
the hardware ELD buffer. Stop doing so.
The one slight caveat here is that this is not strictly legal
according to the HDA spec. PD=1;ELD=0 is only documented as
an intermediate state during modeset. But if there is no hardware
that depends on that then I guess we're fine. Or we could
perhaps set ELD=1 without actually programming the buffer?
Note that the bspec sequence of PD=0;ELD=0 -> PD=1;ELD=0 ->
PD=1;ELD=1 is also not strictly correct according to the HDA
spec, as the only documented transition from PD=0;ELD=0 is
straight to PD=1;ELD=1.
Additionally on hsw/bdw the hardware buffer is tied in with the
dedicated display HDA controller's power state, so currently
we mostly fail at proramming the buffer anyway. When the HDA
side is not sufficiently powered up the ELD address bits get
stuck and the ELD data register accesses go nowhere.
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
References: https://lore.kernel.org/intel-gfx/20221012104936.30911-1-ville.syrjala@linux.intel.com/
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-3-ville.syrjala@linux.intel.com
Since we use the audio component to transfer the ELD to the audio
driver on ilk+ platforms there is no point in even programming
the hardware ELD buffer. Stop doing so.
The one slight caveat here is that this is not strictly legal
according to the HDA spec. PD=1;ELD=0 is only documented as
an intermediate state during modeset. But if there is no hardware
that depends on that then I guess we're fine. Or we could
perhaps set ELD=1 without actually programming the buffer?
Note that the bspec sequence of PD=0;ELD=0 -> PD=1;ELD=0 ->
PD=1;ELD=1 is also not strictly correct according to the HDA
spec, as the only documented transition from PD=0;ELD=0 is
straight to PD=1;ELD=1. But that is not even possible on
these platforms as the bits live in different registers.
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-2-ville.syrjala@linux.intel.com
New DMC releases in linux-firmware will stop using version number in
blob filenames. This new convention provides the following benefits:
1. It simplifies code maintenance, as new DMC releases for a platform
using the new convention will always use the same filename for the
blob.
2. It allows DMC to be loaded even if the target system does not have
the most recent firmware installed.
Prepare the driver by:
- Using the new convention for DMC_PATH() and renaming the currently
used one to make it clear it is for the legacy scheme.
- Implementing a fallback mechanism for future transitions from
versioned to unversioned paths so that we do not cause a regression
for systems not having the most up-to-date linux-firmware files.
v2:
- Keep using request_firmware() instead of firmware_request_nowarn().
(Jani)
v3:
- Keep current DMC paths instead of directly using unversioned ones,
so that we do not disturb initrd generation.
(Lucas, Rodrigo)
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230123182021.31239-2-gustavo.sousa@intel.com
Driver Changes:
Fixes/improvements/new stuff:
- Fix workarounds on Gen2-3 (Tvrtko Ursulin)
- Fix HuC delayed load memory leaks (Daniele Ceraolo Spurio)
- Fix a BUG caused by impendance mismatch in dma_fence_wait_timeout and GuC (Janusz Krzysztofik)
- Add DG2 workarounds Wa_18018764978 and Wa_18019271663 (Matt Atwood)
- Apply recommended L3 hashing mask tuning parameters (Gen12+) (Matt Roper)
- Improve suspend / resume times with VT-d scanout workaround active (Andi Shyti, Chris Wilson)
- Silence misleading "mailbox access failed" warning in snb_pcode_read (Ashutosh Dixit)
- Fix null pointer dereference on HSW perf/OA (Umesh Nerlige Ramappa)
- Avoid trampling the ring during buffer migration (and selftests) (Chris Wilson, Matthew Auld)
- Fix DG2 visual corruption on small BAR systems by not forgetting to copy CCS aux state (Matthew Auld)
- More fixing of DG2 visual corruption by not forgetting to copy CCS aux state of backup objects (Matthew Auld)
- Fix TLB invalidation for Gen12.50 video and compute engines (Andrzej Hajda)
- Limit Wa_22012654132 to just specific steppings (Matt Roper)
- Fix userspace crashes due eviction not working under lock contention after the object locking conversion (Matthew Auld)
- Avoid double free is user deploys a corrupt GuC firmware (John Harrison)
- Fix 32-bit builds by using "%zu" to format size_t (Nirmoy Das)
- Fix a possible BUG in TTM async unbind due not reserving enough fence slots (Nirmoy Das)
- Fix potential use after free by not exposing the GEM context id to userspace too early (Rob Clark)
- Show clamped PL1 limit to the user (hwmon) (Ashutosh Dixit)
- Workaround unreliable reset on Jasperlake (Chris Wilson)
- Cover rest of SVG unit MCR registers (Gustavo Sousa)
- Avoid PXP log spam on platforms which do not support the feature (Alan Previn)
- Re-disable RC6p on Sandy Bridge to avoid GPU hangs and visual glitches (Sasa Dragic)
Future platform enablement:
- Manage uncore->lock while waiting on MCR register (Matt Roper)
- Enable Idle Messaging for GSC CS (Vinay Belgaumkar)
- Only initialize GSC in tile 0 (José Roberto de Souza)
- Media GT and Render GT share common GGTT (Aravind Iddamsetty)
- Add dedicated MCR lock (Matt Roper)
- Implement recommended caching policy (PVC) (Wayne Boyer)
- Add hardware-level lock for steering (Matt Roper)
- Check full IP version when applying hw steering semaphore (Matt Roper)
- Enable GuC GGTT invalidation from the start (Daniele Ceraolo Spurio)
- MTL GSC firmware support (Daniele Ceraolo Spurio, Jonathan Cavitt)
- MTL OA support (Umesh Nerlige Ramappa)
- MTL initial gt workarounds (Matt Roper)
Driver refactors:
- Hold forcewake and MCR lock over PPAT setup (Matt Roper)
- Acquire fw before loop in intel_uncore_read64_2x32 (Umesh Nerlige Ramappa)
- GuC filename cleanups and use submission API version number (John Harrison)
- Promote pxp subsystem to top-level of i915 (Alan Previn)
- Finish proofing the code agains object size overflows (Chris Wilson, Gwan-gyeong Mun)
- Start adding module oriented dmesg output (John Harrison)
Miscellaneous:
- Correct kerneldoc for intel_gt_mcr_wait_for_reg() (Matt Roper)
- Bump up sample period for busy stats selftest (Umesh Nerlige Ramappa)
- Make GuC default_lists const data (Jani Nikula)
- Fix table order verification to check all FW types (John Harrison)
- Remove some limited use register access wrappers (Jani Nikula)
- Remove struct_member macro (Andrzej Hajda)
- Remove hardcoded value with a macro (Nirmoy Das)
- Use helper func to find out map type (Nirmoy Das)
- Fix a static analysis warning (John Harrison)
- Consolidate VMA active tracking helpers (Andrzej Hajda)
- Do not cover all future platforms in TLB invalidation (Tvrtko Ursulin)
- Replace zero-length arrays with flexible-array members (Gustavo A. R. Silva)
- Unwind hugepages to drop wakeref on error (Chris Wilson)
- Remove a couple of superfluous i915_drm.h includes (Jani Nikula)
Merges:
- Merge drm/drm-next into drm-intel-gt-next (Rodrigo Vivi)
danvet: Fix up merge conflict in intel_uc_fw.c, we ended up with 2
copies of try_firmware_load() somehow.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/Y8fW2Ny1B1hZ5ZmF@tursulin-desk
