icl and tgl are still affected by the modulo 4 PLANE_OFFSET.y
underrun issue. Reject such configurations on all gen9+ platforms.
Can be reproduced easily with the following sequence of
hardware poking:
while {
write FBC_CTL.enable=1
wait for vblank
write PLANE_OFFSET .x=0 .y=32
write PLANE_SURF
wait for vblank
# if PLANE_OFFSET.y is multiple of 4 the underrun won't happen
write PLANE_OFFSET .x=0 .y=31
write PLANE_SURF
wait for vblank
# extra vblank wait is required here presumably
# to get FBC into the proper state
wait for vblank
write FBC_CTL.enable=0
# underrun happens some time after FBC disable
wait for vblank
}
Both 8888 and 565 pixel formats and all tilinga formats
seem affected. Reproduced on KBL/GLK/ICL/TGL. BDW confirmed
not affected.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/792
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213133453.22152-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Fix several issues with DSC power domains that did not take DSI
transcoders into account:
- On TGL+ we need to use PW2 for DSC on pipe A, not transcoder A. There
is no longer an eDP transcoder, but there are two DSI transcoders
which may be connected to pipe A.
- On TGL+ we need to use the pipe, not transcoder, power domains for DSC
on pipes other than A. Again, there are DSI transcoders.
- On ICL we need to use PW2 for DSC also for DSI transcoders, not just
for the eDP transcoder.
Using is_pipe_dsc() also adds the warning about ICL pipe A DSC, which
does not exist.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212134728.18432-1-jani.nikula@intel.com
Move all of haswell_crtc_disable() into the encoder
.post_disable() hooks. Now we're left with just
calling the .disable() and .post_disable() hooks
back to back.
I chose to move the code into the .post_disable() hook instead
of the .disable() hook as most of the sequence is currently
implemented in the .post_disable() hook.
We should collapse it all down to just one hook and then the
encoders can drive the modeset sequence fully. But that may
need some further refactoring as we currently call the
ddi .post_disable() hook from mst code and we can't just
replace that with a call to the ddi .disable() hook.
Should also follow up with similar treatment for the enable
sequence but let's start here where it's easier.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213195217.15168-5-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
We have a few places where we want to reset a crtc state to its
default values. Let's add a helper for that. We'll need the new
__drm_atomic_helper_crtc_state_reset() helper for this to allow
us to just reset the state itself without clobbering the
crtc->state pointer.
And while at it let's zero out the whole thing, except a few
choice member which we'll mark as "invalid". And thanks to this
we can now nuke intel_crtc_init_scalers().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107142417.11107-4-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
drm-misc-next for v5.6:
UAPI Changes:
- Add support for DMA-BUF HEAPS.
Cross-subsystem Changes:
- mipi dsi definition updates, pulled into drm-intel as well.
- Add lockdep annotations for dma_resv vs mmap_sem and fs_reclaim.
- Remove support for dma-buf kmap/kunmap.
- Constify fb_ops in all fbdev drivers, including drm drivers and drm-core, and media as well.
Core Changes:
- Small cleanups to ttm.
- Fix SCDC definition.
- Assorted cleanups to core.
- Add todo to remove load/unload hooks, and use generic fbdev emulation.
- Assorted documentation updates.
- Use blocking ww lock in ttm fault handler.
- Remove drm_fb_helper_fbdev_setup/teardown.
- Warning fixes with W=1 for atomic.
- Use drm_debug_enabled() instead of drm_debug flag testing in various drivers.
- Fallback to nontiled mode in fbdev emulation when not all tiles are present. (Later on reverted)
- Various kconfig indentation fixes in core and drivers.
- Fix freeing transactions in dp-mst correctly.
- Sean Paul is steping down as core maintainer. :-(
- Add lockdep annotations for atomic locks vs dma-resv.
- Prevent use-after-free for a bad job in drm_scheduler.
- Fill out all block sizes in the P01x and P210 definitions.
- Avoid division by zero in drm/rect, and fix bounds.
- Add drm/rect selftests.
- Add aspect ratio and alternate clocks for HDMI 4k modes.
- Add todo for drm_framebuffer_funcs and fb_create cleanup.
- Drop DRM_AUTH for prime import/export ioctls.
- Clear DP-MST payload id tables downstream when initializating.
- Fix for DSC throughput definition.
- Add extra FEC definitions.
- Fix fake offset in drm_gem_object_funs.mmap.
- Stop using encoder->bridge in core directly
- Handle bridge chaining slightly better.
- Add backlight support to drm/panel, and use it in many panel drivers.
- Increase max number of y420 modes from 128 to 256, as preparation to add the new modes.
Driver Changes:
- Small fixes all over.
- Fix documentation in vkms.
- Fix mmap_sem vs dma_resv in nouveau.
- Small cleanup in komeda.
- Add page flip support in gma500 for psb/cdv.
- Add ddc symlink in the connector sysfs directory for many drivers.
- Add support for analogic an6345, and fix small bugs in it.
- Add atomic modesetting support to ast.
- Fix radeon fault handler VMA race.
- Switch udl to use generic shmem helpers.
- Unconditional vblank handling for mcde.
- Miscellaneous fixes to mcde.
- Tweak debug output from komeda using debugfs.
- Add gamma and color transform support to komeda for DOU-IPS.
- Add support for sony acx424AKP panel.
- Various small cleanups to gma500.
- Use generic fbdev emulation in udl, and replace udl_framebuffer with generic implementation.
- Add support for Logic PD Type 28 panel.
- Use drm_panel_* wrapper functions in exynos/tegra/msm.
- Add devicetree bindings for generic DSI panels.
- Don't include drm_pci.h directly in many drivers.
- Add support for begin/end_cpu_access in udmabuf.
- Stop using drm_get_pci_dev in gma500 and mga200.
- Fixes to UDL damage handling, and use dma_buf_begin/end_cpu_access.
- Add devfreq thermal support to panfrost.
- Fix hotplug with daisy chained monitors by removing VCPI when disabling topology manager.
- meson: Add support for OSD1 plane AFBC commit.
- Stop displaying garbage when toggling ast primary plane on/off.
- More cleanups and fixes to UDL.
- Add D32 suport to komeda.
- Remove globle copy of drm_dev in gma500.
- Add support for Boe Himax8279d MIPI-DSI LCD panel.
- Add support for ingenic JZ4770 panel.
- Small null pointer deference fix in ingenic.
- Remove support for the special tfp420 driver, as there is a generic way to do it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba73535a-9334-5302-2e1f-5208bd7390bd@linux.intel.com
At least Bay Trail (BYT) and Cherry Trail (CHT) devices can use 1 of 2
different PWM controllers for controlling the LCD's backlight brightness.
Either the one integrated into the PMIC or the one integrated into the
SoC (the 1st LPSS PWM controller).
So far in the LPSS code on BYT we have skipped registering the LPSS PWM
controller "pwm_backlight" lookup entry when a Crystal Cove PMIC is
present, assuming that in this case the PMIC PWM controller will be used.
On CHT we have been relying on only 1 of the 2 PWM controllers being
enabled in the DSDT at the same time; and always registered the lookup.
So far this has been working, but the correct way to determine which PWM
controller needs to be used is by checking a bit in the VBT table and
recently I've learned about 2 different BYT devices:
Point of View MOBII TAB-P800W
Acer Switch 10 SW5-012
Which use a Crystal Cove PMIC, yet the LCD is connected to the SoC/LPSS
PWM controller (and the VBT correctly indicates this), so here our old
heuristics fail.
This commit fixes using the wrong PWM controller on these devices by
calling pwm_get() for the right PWM controller based on the
VBT dsi.config.pwm_blc bit.
Note this is part of a series which contains 2 other patches which renames
the PWM lookup for the 1st SoC/LPSS PWM from "pwm_backlight" to
"pwm_pmic_backlight" and the PWM lookup for the Crystal Cove PMIC PWM
from "pwm_backlight" to "pwm_pmic_backlight".
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191216202906.1662893-4-hdegoede@redhat.com
According to both the old acpi_igd_opregion_spec_0.pdf and the newer
skl_opregion_rev0p5.pdf opregion specification documents, if a driver
handles hotplug events itself, it should set the opregion CHPD field to
1 to indicate this and the firmware should respond to this by no longer
sending ACPI 0x00 notification events on e.g. lid-state changes.
Specifically skl_opregion_rev0p5.pdf states thid in the documentation of
the CHPD word: "Re-enumeration trigger logic in System BIOS MUST be
disabled for all the Operating Systems supporting Hot-Plug
(e.g., Windows* Longhorn and above)." Note the MUST in there.
We ignore these notifications, so this should not be a problem but many
recent DSTDs seem to all have the same copy-pasted bug in the GNOT() AML
function which is used to send these notifications. Windows likely does not
hit this bug as it presumably correcty sets CHPD to 1.
Here is an example of the broken GNOT() method:
Method (GNOT, 2, NotSerialized)
{
...
CEVT = Arg0
CSTS = 0x03
If (((CHPD == Zero) && (Arg1 == Zero)))
{
If (((OSYS > 0x07D0) || (OSYS < 0x07D6)))
{
Notify (PCI0, Arg1)
}
Else
{
Notify (GFX0, Arg1)
}
}
...
Notice that the condition for the If is always true I believe that the
|| like needs to be an &&, but there is nothing we can do about this and
in my own DSDT archive 55 of the 93 DSDTs have this issue.
When the if is true the notification gets send to the PCI root instead
of only to the GFX0 device. This causes Linux to re-enumerate PCI devices
whenever the LID opens / closes, leading to unexpected messages in dmesg:
Suspend through lid close:
[ 313.598199] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
[ 313.664453] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
[ 313.737982] pci_bus 0000:01: Allocating resources
[ 313.738036] pcieport 0000:00:1c.0: bridge window [io 0x1000-0x0fff] to [bus 01] add_size 1000
[ 313.738051] pcieport 0000:00:1c.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 add_align 100000
[ 313.738111] pcieport 0000:00:1c.0: BAR 15: assigned [mem 0x91000000-0x911fffff 64bit pref]
[ 313.738128] pcieport 0000:00:1c.0: BAR 13: assigned [io 0x1000-0x1fff]
Resume:
[ 813.623894] pci 0000:00:03.0: [8086:22b8] type 00 class 0x048000
[ 813.623955] pci 0000:00:03.0: reg 0x10: [mem 0x00000000-0x003fffff]
[ 813.630477] pci 0000:00:03.0: BAR 0: assigned [mem 0x91c00000-0x91ffffff]
[ 854.579101] intel_atomisp2_pm 0000:00:03.0: Refused to change power state, currently in D3
And more importantly this re-enumeration races with suspend/resume causing
enumeration to not be complete when assert_isp_power_gated() from
drivers/gpu/drm/i915/display/intel_display_power.c runs. This causes
the !pci_dev_present(isp_ids) check in assert_isp_power_gated() to fail
making the condition for the WARN true, leading to:
[ 813.327886] ------------[ cut here ]------------
[ 813.327898] ISP not power gated
[ 813.328028] WARNING: CPU: 2 PID: 2317 at drivers/gpu/drm/i915/display/intel_display_power.c:4870 intel_display_print_error_state+0x2b98/0x3a80 [i915]
...
[ 813.328599] ---[ end trace f01e81b599596774 ]---
This commit fixes the unwanted ACPI notification on the PCI root device
by setting CHPD to 1, so that the broken if condition in the AML never
gets checked as notifications of type 0x00 are disabled altogether.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212204828.191288-1-hdegoede@redhat.com
Just like in commit 523e0cc89b ("drm/i915/tgl: allow DVI/HDMI on port
A"), the port checks when reading the VBT can easily not match what the
platform really exposes. However here we only have some additional debug
messages that are not adding much value: in the previous debug message
we already print everything we know about the VBT.
Instead of keep fixing the possible port assignments according to the
platform, just nuke the additional messages.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191206190552.8818-1-lucas.demarchi@intel.com
Now that the combo PHY aux power well handlers are used exclusively on
Icelake, we can drop a bunch of the extra tests.
v2: Don't try to use intel_uncore_rmw for register updates yet; there's
pending display uncore patches that need to land first. (Lucas)
v3: Drop the combo phy assertion. It was backward before, but doesn't
seem terribly necessary. I'm keeping the IS_ICELAKE assertion
though since we often copy/paste/modify the power well tables when
defining new platforms and it's too easy to cargo cult the
ICL-specific handling to new platforms that shouldn't use it.
(Lucas)
v4: Fix build; forgot to commit all the changes. (CI)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191213010600.701315-1-matthew.d.roper@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
In order to eliminate intel_pipe_to_cpu_transcoder() (and its
crtc->config usage) let's pass the cpu transcoder to
assert_pipe() so we don't have to do the pipe->cpu transcoder
lookup on HSW+.
On VLV/CHV this can get called during eDP init, which
happens before crtc->config->cpu_transcoder is even
populated. So currently we're always reading PIPECONF(A)
there even if we're trying to check the state of some
other pipe.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191112163812.22075-4-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
