This add support for the Khadas TS050 1080x1920 5" LCD DSI panel designed to work
with the Khadas Edge-V, Captain, VIM3 and VIM3L Single Board Computers.
It provides a MIPI DSI interface to the host, a built-in LED backlight
and touch controller.
The init values was taken from the vendor source tree, comments were added to the
know values but most of the init table is undocumented.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
[narmstrong: call drm_panel_remove if mipi_dsi_attach fails]
Link: https://patchwork.freedesktop.org/patch/msgid/20201204081949.38418-3-narmstrong@baylibre.com
The DSI version of the panel behaved instable and close
scrutiny of the vendor driver from the Samsung
GT-S8190 shows a different initialization sequence for
the DSI mode panel than the DPI mode panel.
Make the initialization depend on whether we are in
DSI or DPI mode and handle the differences.
After this the panel on the GT-I8190 becomes much more
stable.
Also spell out some more custom DCS commands found in
the vendor source code to cut down a bit on magic
where we can.
Fixes: f0aee45ffc ("drm/panel: s6e63m0: Fix init sequence")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Stephan Gerhold <stephan@gerhold.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20201205122229.1952980-1-linus.walleij@linaro.org
Add support for the BOE NV110WTM-N61 panel. The EDID lists two modes
(one for 60 Hz refresh rate and one for 40 Hz), so we'll list both of
them here.
Note that the panel datasheet requires 80 ms between HPD asserting and
the backlight power being turned on. We'll use the new timing
constraints structure to do this cleanly. This assumes that the
backlight will be enabled _after_ the panel enable finishes. This is
how it works today and seems a sane assumption.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201109170018.v4.4.I71b2118dfc00fd7b43b02d28e7b890081c2acfa2@changeid
On the panel I'm looking at, there's an 80 ms minimum time between HPD
being asserted by the panel and setting the backlight enable GPIO.
While we could just add an 80 ms "enable" delay, this is not ideal.
Link training is allowed to happen in parallel with this delay so the
fixed 80 ms delay over-delays.
We'll support this by logging the time at the end of prepare and then
delaying in enable if enough time hasn't passed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201109170018.v4.3.Ib9ce3c6482f464bf594161581521ced46bbd54ed@changeid
It is believed that all of the current users of the "unprepare" delay
don't actually need to wait the amount of time specified directly in
the unprepare phase. The purpose of the delay that's specified is to
allow the panel to fully power off so that we don't try to power it
back on before it's managed to full power down.
Let's use this observation to avoid the fixed delay that we currently
have. Instead of delaying, we'll note the current time when the
unprepare happens. If someone then tries to prepare the panel later
and not enough time has passed, we'll do the delay before starting the
prepare phase.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201109170018.v4.2.I06a95d83e7fa1bd919c8edd63dacacb5436e495a@changeid
The probe routine acquires the reset GPIO using GPIOD_OUT_LOW. Directly
afterwards it calls acx565akm_detect(), which sets the GPIO value to
HIGH. If the bootloader initialized the GPIO to HIGH before the probe
routine was called, there is only a very short time period of a few
instructions where the reset signal is LOW. Exact time depends on
compiler optimizations, kernel configuration and alignment of the stars,
but I expect it to be always way less than 10us. There are no public
datasheets for the panel, but acx565akm_power_on() has a comment with
timings and reset period should be at least 10us. So this potentially
brings the panel into a half-reset state.
The result is, that panel may not work after boot and can get into a
working state by re-enabling it (e.g. by blanking + unblanking), since
that does a clean reset cycle. This bug has recently been hit by Ivaylo
Dimitrov, but there are some older reports which are probably the same
bug. At least Tony Lindgren, Peter Ujfalusi and Jarkko Nikula have
experienced it in 2017 describing the blank/unblank procedure as
possible workaround.
Note, that the bug really goes back in time. It has originally been
introduced in the predecessor of the omapfb driver in commit 3c45d05be3
("OMAPDSS: acx565akm panel: handle gpios in panel driver") in 2012.
That driver eventually got replaced by a newer one, which had the bug
from the beginning in commit 84192742d9 ("OMAPDSS: Add Sony ACX565AKM
panel driver") and still exists in fbdev world. That driver has later
been copied to omapdrm and then was used as a basis for this driver.
Last but not least the omapdrm specific driver has been removed in
commit 45f16c82db ("drm/omap: displays: Remove unused panel drivers").
Reported-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Reported-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fixes: 1c8fc3f0c5 ("drm/panel: Add driver for the Sony ACX565AKM panel")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201127200429.129868-1-sebastian.reichel@collabora.com
The init sequence consist of a number of unknown settings
for the display controller. This patch achieves two things:
- Fix an error that must have happened when the driver was
converted from the backlight subsystem: the 0xb8
configuration command was lost and added as a tail to
the previous command.
- Update some minor settings in some bytes here and there
according to changes in the Samsung GT-I9070 and
Samsung GT-S7710 code dumps. Since two other devices use
these settings they probably reflect trimmings later
found to be better for the display rather than
customizations for these devices.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201117175621.870085-3-linus.walleij@linaro.org
Copy over the width/height in millimeters to the
(somewhat redundant) display info, and set up the
bus format and bus flags for the display.
When used as DPI this display requires DE to be
active low and pixel data to be output on the
negative edge. It might be that it was previously
used with a display controller that either does
not support these settings or was hardcoded to use
these as default. This information comes from the
source code of the Samsung GT-I9070 mobile phone.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201110234653.2248594-6-linus.walleij@linaro.org
The OnePlus 6/T devices use different panels however they are
functionally identical with the only differences being the resolution.
The panels also don't seem to be used by any other devices, just combine
them into one driver.
The panels are: samsung,sofef00
and samsung,s6e3fc2x01
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
[fixed checkpatch warnings]
Link: https://patchwork.freedesktop.org/patch/msgid/20201112161920.2671430-2-caleb@connolly.tech
Fixes the following W=1 kernel build warning(s):
drivers/gpu/drm/panel/panel-ilitek-ili9322.c:177: warning: Enum value 'ILI9322_INPUT_SRGB_THROUGH' not described in enum 'ili9322_input'
drivers/gpu/drm/panel/panel-ilitek-ili9322.c:177: warning: Enum value 'ILI9322_INPUT_SRGB_ALIGNED' not described in enum 'ili9322_input'
drivers/gpu/drm/panel/panel-ilitek-ili9322.c:177: warning: Enum value 'ILI9322_INPUT_SRGB_DUMMY_320X240' not described in enum 'ili9322_input'
drivers/gpu/drm/panel/panel-ilitek-ili9322.c:177: warning: Enum value 'ILI9322_INPUT_SRGB_DUMMY_360X240' not described in enum 'ili9322_input'
drivers/gpu/drm/panel/panel-ilitek-ili9322.c:177: warning: Enum value 'ILI9322_INPUT_DISABLED_1' not described in enum 'ili9322_input'
drivers/gpu/drm/panel/panel-ilitek-ili9322.c:177: warning: Enum value 'ILI9322_INPUT_PRGB_THROUGH' not described in enum 'ili9322_input'
drivers/gpu/drm/panel/panel-ilitek-ili9322.c:177: warning: Enum value 'ILI9322_INPUT_PRGB_ALIGNED' not described in enum 'ili9322_input'
drivers/gpu/drm/panel/panel-ilitek-ili9322.c:177: warning: Enum value 'ILI9322_INPUT_YUV_640X320_YCBCR' not described in enum 'ili9322_input'
drivers/gpu/drm/panel/panel-ilitek-ili9322.c:177: warning: Enum value 'ILI9322_INPUT_YUV_720X360_YCBCR' not described in enum 'ili9322_input'
drivers/gpu/drm/panel/panel-ilitek-ili9322.c:177: warning: Enum value 'ILI9322_INPUT_DISABLED_2' not described in enum 'ili9322_input'
drivers/gpu/drm/panel/panel-ilitek-ili9322.c:177: warning: Enum value 'ILI9322_INPUT_ITU_R_BT656_720X360_YCBCR' not described in enum 'ili9322_input'
drivers/gpu/drm/panel/panel-ilitek-ili9322.c:177: warning: Enum value 'ILI9322_INPUT_ITU_R_BT656_640X320_YCBCR' not described in enum 'ili9322_input'
drivers/gpu/drm/panel/panel-ilitek-ili9322.c:177: warning: Enum value 'ILI9322_INPUT_UNKNOWN' not described in enum 'ili9322_input'
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105144517.1826692-17-lee.jones@linaro.org
Novatek NT36672a is a generic DSI IC that drives command and video mode
panels. Add the driver for it.
Right now adding support for some Poco F1 phones that have an LCD panel
from Tianma connected with this IC, with a resolution of 1080x2246 that
operates in DSI video mode.
During testing, Benni Steini <bennisteinir@gmail.com> helped us fix
the reset sequence timing (from 10ms to 20ms), to get the bootanimation
to work on Android.
With current AOSP, we need to increase it to 200ms - this seems to be a
safe high value to avoid a white screen occasionally.
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Benni Steini <bennisteinir@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200902064407.30712-3-sumit.semwal@linaro.org
The upstream S6E63M0 driver has some peculiarities around
the prepare/enable disable/unprepare sequence: the screen
is taken out of sleep in prepare() as part of
s6e63m0_init() the put to on with MIPI_DCS_SET_DISPLAY_ON
in enable().
However it is just put into sleep mode directly in
disable(). As disable()/enable() can be called without
unprepare()/prepare() being called, this is unbalanced,
we should take the display out of sleep in enable()
then turn it off().
Further MIPI_DCS_SET_DISPLAY_OFF is never called
balanced with MIPI_DCS_SET_DISPLAY_ON.
The vendor driver for Samsung GT-I8190 (Golden) does all
of these things in strict order.
Augment the driver to do exit sleep/set display on in
enable() and set display off/enter sleep in disable().
Further send an explicit reset pulse in power_on() so we
come up in a known state, and issue the MCS_ERROR_CHECK
command after setting display on like the vendor driver
does. Also use the timings from the vendor driver in
the sequence.
Doing all of these things makes the display much more
stable on the Samsung GT-I8190 when enabling/disabling
the display pipeline.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200817213906.88207-1-linus.walleij@linaro.org
This panel can be accessed using both SPI and DSI.
To make it possible to probe and use the device also from
a DSI bus, first break out the SPI support to its own file.
Since all the panel driver does is write DCS commands to
the panel, we pass a DCS write function to probe()
from each subdriver.
We make the Kconfig entry for SPI mode default so all
current users will continue to work.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/384873/
