Update addresses of PCIE link width registers,
& link width format used to populate gpu metrics
table for smu v13.0.6
v2:
Removed ESM register update
v3:
Updated patch subject and message
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The parameter amdgpu_mcbp shall have priority against the default value
calculated from the chip version.
User could disable mcbp by setting the parameter mcbp as zero.
v2: do not trigger preemption in sw ring muxer when mcbp is disabled.
Signed-off-by: Jiadong Zhu <Jiadong.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This panel has been implemented in commit eae7488814 ("drm/panel-simple:
Add Innolux G156HCE-L01 panel entry") with a higher clock than the typical
one mentioned on the documentation to avoid flickering on the unit
tested. Testing on a different unit shows that the panel actually works
with the intended 70.93 MHz clock and even lower frequencies so the
flickering is likely caused either by a defective unit or by other
different components such as the bridge.
Fixes: eae7488814 ("drm/panel-simple: Add Innolux G156HCE-L01 panel entry")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Tested-by: Marek Vasut <marex@denx.de> # MX8MM with LT9211
Reviewed-by: Marek Vasut <marex@denx.de>
[narmstrong: fixed commit id in commit msg]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230814134024.397739-1-luca.ceresoli@bootlin.com
DCN 3.1.4 is reported to hang on s2idle entry if graphics activity
is happening during entry. This is because GFXOFF was scheduled as
delayed but RLC gets disabled in s2idle entry sequence which will
hang GFX IP if not already in GFXOFF.
To help this problem, flush any delayed work for GFXOFF early in
s2idle entry sequence to ensure that it's off when RLC is changed.
commit 4b31b92b14 ("drm/amdgpu: complete gfxoff allow signal during
suspend without delay") modified power gating flow so that if called
in s0ix that it ensured that GFXOFF wasn't put in work queue but
instead processed immediately.
This is dead code due to commit 10cb67eb8a ("drm/amdgpu: skip
CG/PG for gfx during S0ix") because GFXOFF will now not be explicitly
called as part of the suspend entry code. Remove that dead code.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tim Huang <tim.huang@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX v11.0.1 reported fence fallback timer expired issue on
SDMA and GFX rings after S0ix resume. This is generated by
EOP interrupts are disabled when S0ix suspend but fails to
re-enable when resume because of the GFX is in GFXOFF.
[ 203.349571] [drm] Fence fallback timer expired on ring sdma0
[ 203.349572] [drm] Fence fallback timer expired on ring gfx_0.0.0
[ 203.861635] [drm] Fence fallback timer expired on ring gfx_0.0.0
For S0ix, GFX is in GFXOFF state, avoid to touch the GFX registers
to configure the fence driver interrupts for rings that belong to GFX.
The interrupts configuration will be restored by GFXOFF exit.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update pcie link speed registers for smu v13.0.6 &
populate gpu metric table with pcie link speed rather than
gen for smu v13_0_0, smu v13_0_6 & smu v13_0_7
v2:
Update ESM register address
Used macro to convert pcie gen to speed
v3:
Chaged macro to inline function for pcie gen to speed
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update addresses of PCIE link width registers,
& link width format used to populate gpu metrics
table for smu v13.0.6
v2:
Removed ESM register update
v3:
Updated patch subject and message
Signed-off-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Improve power saving feature
- Clean up for code clarity
- Fix crashing bug
- Fix pipe allocation for older ASIC
- Fix for gamut remap
- Fix 8K 60Hz display in test cases
- Fix bug in clock gating
- Improve DP2 compliance
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some ASICS only offer one type of power attribute, so in the visible
callback check whether the attributes are supported and hide if not
supported.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Aldebaran can only return average socket power for the first die.
The other dies return 0. Instead of returning a bad value, return
-EOPNOTSUPP so that the attribute will be hidden.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The average power for the GPU metrics sysfs file contains the input
power not the average power. The member that is set is called average
power though, so correct it to the right value.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
PCI core API pci_dev_id() can be used to get the BDF number for a pci
device. We don't need to compose it mannually. Use pci_dev_id() to
simplify the code a little bit.
Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove duplicated includes in amdgpu_amdkfd_gpuvm.c and amdgpu_ttm.c.
Resolves checkincludes message.
Signed-off-by: GUO Zihua <guozihua@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following errors reported by checkpatch:
ERROR: open brace '{' following enum go on the same line
ERROR: open brace '{' following struct go on the same line
Signed-off-by: Ran Sun <sunran001@208suo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix the following errors reported by checkpatch:
ERROR: trailing whitespace
ERROR: open brace '{' following struct go on the same line
ERROR: code indent should use tabs where possible
Signed-off-by: Ran Sun <sunran001@208suo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allow the user to specify -2 as auto enabled with displays.
By default we don't enter runtime suspend when there are
displays attached because it does not work well in some
desktop environments due to the driver sending hotplug
events on resume in case any new displays were attached
while the GPU was powered down. Some users still want
this functionality though, so this lets you enable it.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2428
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some GPUs provide support for current power, some average power,
and some both. To be able to support all these combinations,
introduce a new attribute.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is a lack of encapsulation of pipe connection representation in pipe context.
This has caused many challenging bugs and coding errors with repeated
logic to identify the same pipe type.
[how]
Formally define pipe types and provide getters to identify a pipe type and
find a pipe based on specific requirements. Update existing logic in non dcn
specific files and dcn32 and future versions to use the new accessors.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
8k60hz compliace test failing because we restrict it single memory
channels. Workaround by not restricting it on single displays.
[How]
Adding an additional check to DCN314 to restrict 8k60hz mode if it has
more than 1 display connected.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is a recent work for developing a new pipe resource allocation
policy used for new ASIC. The new code change needs to modify asic
independent pipe resource allocation flow and hook up the new allocation
policy in asic dependent layer. Unfortunately this change revealed a
hidden bug in the old pipe resource allocation sequence used for older
asics. In the older version of acquiring pipe for layer, we are always
assigning otg master's opp and tg to the newly allocated secondary dpp
pipe. This logic is incorrect when the secodnary dpp
pipe is connected to a secondary opp head pipe in ODM combine
configuration. Before the recent change, we will overwrite this wrong
assignement in asic independent layer again. This covers up the issue.
With the recent change, we will no longer cover up this in upper layer
and therefore causes wrong tg and opp assignement to the secondary
dpp pipe connected to a secondary opp head.
[how]
Always assign tg and opp from its own opp head instead of otg master.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
If surface format is dynamically changed within app without changing
timing / whole plane, we don't reprogram gamut remap matrix.
Issue example:
Linear FP16 scRGB going to PQ+BT.2020 monitor.
Remap = scRGB->BT.2020
App switches swapchain format to 10-bit PQ+BT.2020.
SW calculates correctly that new Remap = bypass (in=-out=BT.2020).
But update not applied in HW.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For sriov, doorbell index for vcn0 for AID needs to be on
32 byte boundary so we need to move the vcn end doorbell
Signed-off-by: Samir Dhume <samir.dhume@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
KFD currently relies on MEC FW to clear tcp watch control
register on UNMAP_PROCESS, but FW doesn't work on it,
which is a bug. So the solution is to clear the register
as gfx v9 in KFD.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Reviewed-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
