XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy
has a dedicated PIPE 5.2 Message bus for configuration. This message
bus is used to configure the phy internal registers.
XELPDP has C10 phys to drive output to the EDP and the native output
from the display engine. Add structures, programming hardware state
readout logic. Port clock calculations are similar to DG2. Use the DG2
formulae to calculate the port clock but use the relevant pll signals.
Note: PHY lane 0 is always used for PLL programming.
Add sequences for C10 phy enable/disable phy lane reset,
powerdown change sequence and phy lane programming.
Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636
v2: Squash patches related to C10 phy message bus and pll
programming support (Jani)
Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani)
Move macro definitions (Jani)
DP rates as separate patch (Jani)
Spin out xelpdp register definitions into a separate file (Jani)
Replace macro to select registers based on phy lane with
function calls (Jani)
Fix styling issues (Jani)
Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas)
v3: Move clear request flag into try-loop
v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani)
use __intel_de_wait_for_register() instead of __intel_wait_for_register
and uncomment intel_uncore.h (Jani)
Add DP-alt support for PHY lane programming (Khaled)
v4: Add tx and cmn on c10mpllb_state (Imre)
Add missing waits for pending transactions between two message bus
writes (Imre)
General cleanups and simplifications (Imre)
v5: Few nit cleanups from rev4 (imre)
s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK)
Rebase
v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function
Fix typo in comment for REG_FIELD_PREP8 definition(Imre)
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Gustavo Sousa <gustavo.sousa@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v4)
Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
The goal has been to just make device info a pointer to static const
data, i.e. the static const structs in i915_pci.c. See [1]. However,
there were issues with intel_device_info_runtime_init() clearing the
display sub-struct of device info on the !HAS_DISPLAY() path, which
consequently disables a lot of display functionality, like it
should. Looks like we'd have to cover all those paths, and maybe
sprinkle HAS_DISPLAY() checks in them, which we haven't gotten around
to.
In the mean time, hide mkwrite_device_info() better within
intel_device_info.c by adding a intel_device_info_driver_create() for
the very early initialization of the device info and initial runtime
info. This also lets us declutter i915_drv.h a bit, and stops promoting
mkwrite_device_info() as something that could be used.
[1] https://lore.kernel.org/r/a0422f0a8ac055f65b7922bcd3119b180a41e79e.1655712106.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230411105643.292416-1-jani.nikula@intel.com
Instead of mixing display & non-display stuff together, move
display specific clock info to new debugfs. This patch will
create a new debugfs "i915_cdclk_info" to expose Current & Max
cdclk and Max pixel clock frequency info.
Example:
$ cat /sys/kernel/debug/dri/0/i915_cdclk_info
Current CD clock frequency: 163200 kHz
Max CD clock frequency: 652800 kHz
Max pixel clock frequency: 1305600 kHz
V2: - s/i915_display_clock_info/i915_cdclk_info/ (Jani)
- Move the logic to intel_cdclk.c (Jani)
- Don't remove info from i915_frequency_info (Jani)
V3: - Drop locking (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Bhanuprakash Modem <bhanuprakash.modem@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230413114502.1105288-1-bhanuprakash.modem@intel.com
If the panel supports VRR it must be capable of accepting
timings with arbitrary vblank length, within the valid VRR
range. Use that fact to allow the user to request any refresh
rate they like. We simply pick the next highest fixed mode
from our list, and adjust the vblank to get the desired refresh
rate in the end.
Of course currently everything to do with the vrefresh is
using 1Hz precision, so might not be exact. But we can improve
that in the future by just upping our vrefresh precision.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230404175431.23064-1-ville.syrjala@linux.intel.com
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
If we have to force the hardware to go through a full modeset
due to eg. cdclk reprogramming, we need to preserve
crtc_state->inherited for all crtcs that have not otherwise
gone through the whole compute_config() stuff after connectors
have been detected.
Otherwise eg. cdclk induced modeset glk_force_audio_cdclk()
will clear the inherited flag, and thus the first real commit
coming from userspace later on will not be forced through
the full .compute_config() path and so eg. audio state may
not get properly recomputed.
But instead of adding all kinds of ad-hoc crtc_state->inherited
preservation hacks all over, let's change things so that we
only clear it for the crtcs directly included in userspace/client
initiated commits.
Should be far less fragile since now we just need to remember
to flag the internal commits, and not worry about where new
crtcs might get pulled in.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5260
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230328122357.1697-1-ville.syrjala@linux.intel.com
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Due to raven/raven2 maybe enable sclk slow down,
they cannot get clock count by the RLC at the auto level of dpm performance.
So switch to golden tsc register.
Suggested-by: shanshengwang <shansheng.wang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Jesse Zhang <jesse.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rework retry fault removal from the software filter by
storing an expired timestamp for a fault that is being removed.
When a new fault comes, and it matches an entry in the sw filter,
it will be added as a new fault only when its timestamp is greater
than the timestamp expiry of the fault in the sw filter.
This helps in avoiding stale faults being added back into the
filter and preventing legitimate faults from being handled.
Suggested-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch enables the IH retry CAM on GFX9 series cards. This
retry filter is used to prevent sending lots of retry interrupts
in a short span of time and overflowing the IH ring buffer. This
will also help reduce CPU interrupt workload.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
clang with W=1 reports
drivers/gpu/drm/amd/amdgpu/../pm/swsmu/amdgpu_smu.c:1700:6: error: variable
'num_of_active_display' set but not used [-Werror,-Wunused-but-set-variable]
int num_of_active_display = 0;
^
This variable is not used so remove it.
Fixes: 75145aab7a ("drm/amdgpu/swsmu: clean up a bunch of stale interfaces")
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All chips that support RAS also support IP discovery, so
use the IP versions rather than a mix of IP versions and
asic types. Checking the validity of the atom_ctx pointer
is not required as the vbios is already fetched at this
point.
v2: add comments to id asic types based on feedback from Luben
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Luben Tuikov <luben.tuikov@amd.com>
Move VRR enabling/disabling into a place where it also works
for fastsets.
With this we always start the transcoder up in non-VRR mode.
Granted we already did that but for a very short period of
time. But now that we might end up doing a bit more with the
transcoder in non-VRR mode it seems prudent to also update
the active timings as the transcoder changes its operating
mode.
crtc_state->vrr.enable still tracks whether VRR is actually
enabled or not, but now we configure all the other VRR timing
registers whenever VRR is possible (whether we actually enable
it or not). crtc_state->vrr.flipline can now serve as our
"is VRR possible" bit of state.
I decided to leave the MSA timing ignore bit set all the time
whether VRR is actually enabled or not. If the sink can figure
out the timings with that information when VRR is active then
surely it can also do it when VRR is inactive.
v2: Protect intel_vrr_set_transcoder_timings() with HAS_VRR()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321135615.27338-1-ville.syrjala@linux.intel.com
Reviewed-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
By default the indirect state sampler data (border colors) are stored
in the same heap as the SAMPLER_STATE structure. For userspace drivers
that can be 2 different heaps (dynamic state heap & bindless sampler
state heap). This means that border colors have to copied in 2
different places so that the same SAMPLER_STATE structure find the
right data.
This change is forcing the indirect state sampler data to only be in
the dynamic state pool (more convenient for userspace drivers, they
only have to have one copy of the border colors). This is reproducing
the behavior of the Windows drivers.
BSpec: 46052
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Haridhar Kalvala <haridhar.kalvala@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230407093237.3296286-1-lionel.g.landwerlin@intel.com
(cherry picked from commit 16fc9c08f0)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Enable SDMA queue empty context switching. SDMA context switch due to
quantum programming no longer done here (as of sdma v6), so re-name
sdma_v6_0_ctx_switch_enable to sdma_v6_0_ctxempty_int_enable to reflect
this.
Also program SDMAx_QUEUEx_SCHEDULE_CNTL for context switch due to
quantum in KFD. Set to amdgpu_sdma_phase_quantum (defaults to 32 i.e.
3200us).
Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: Stanley Yang <Stanley.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CP_HQD_HQ_STATUS0[29] bit will be used by CPFW to acknowledge whether
PCIe atomics are supported. The default value of this bit is set
to 0. Driver will check whether PCIe atomics are supported and set the
bit to 1 if supported. This will force CPFW to use real atomic ops.
If the bit is not set, CPFW will default to read/modify/write using the
firmware itself.
This is applicable only to GFX11 RS64 CP with MEC FW >= 509. If MEC
FW < 509 and for all GFX11 F32 CP, PCIe atomics needs to be supported
else it will skip the device.
This commit also involves moving amdgpu_amdkfd_device_probe() function
call after per-IP early_init loop in amdgpu_device_ip_early_init()
function so as to check for RS64 enabled device.
Signed-off-by: Sreekant Somasekharan <sreekant.somasekharan@amd.com>
Reviewed-by: Graham Sider <Graham.Sider@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
XGMI RAS should be according to the gmc xgmi physical nodes number,
XGMI RAS should not be enabled if xgmi num_physical_nodes is zero.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Aldebaran supports VCN and JPEG RAS, it reports unexpected
block id message during VCN and JPEG RAS initialization if VCN
and JPEG block id not defined.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
