Flush mechanism for DSPP blocks has changed in sc7280 family, it
allows individual sub blocks to be flushed in coordination with
master flush control.
Representation: master_flush && (PCC_flush | IGC_flush .. etc )
This change adds necessary support for the above design.
Changes in v1:
- Few nits (Doug, Dmitry)
- Restrict sub-block flush programming to dpu_hw_ctl file (Dmitry)
Changes in v2:
- Move the address offset to flush macro (Dmitry)
- Separate ops for the sub block flush (Dmitry)
Changes in v3:
- Reuse the DPU_DSPP_xx enum instead of a new one (Dmitry)
Changes in v4:
- Use shorter version for unsigned int (Stephen)
Changes in v5:
- Spurious patch please ignore.
Changes in v6:
- Add SOB tag (Doug, Dmitry)
Changes in v7:
- Cache flush mask per dspp (Dmitry)
- Few nits (Marijn)
Changes in v8:
- Few nits (Marijn)
Changes in v9:
- Use DSPP enum while accessing flush mask to make it readable (Dmitry)
- Few nits (Dmitry)
Changes in v10:
- Fix white spaces in a separate patch (Dmitry)
Changes in v11:
- Define a macro for dspp flush selection (Marijn)
- Few nits (Marijn)
Changes in v12:
- Minor comments (reorder macros and a condition) (Marijn)
Signed-off-by: Kalyan Thota <quic_kalyant@quicinc.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/520701/
Link: https://lore.kernel.org/r/1674814487-2112-1-git-send-email-quic_kalyant@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Move code from ad-hoc fbdev callbacks into DRM client functions
and remove the old callbacks. The functions instruct the client
to poll for changed output or restore the display. The DRM core
calls both, the old callbacks and the new client helpers, from
the same places. The new functions perform the same operation as
before, so there's no change in functionality.
Replace all code that initializes or releases fbdev emulation
throughout the driver. Instead initialize the fbdev client by a
single call to msm_fbdev_setup() after msm has registered its
DRM device. As in most drivers, msm's fbdev emulation now acts
like a regular DRM client.
The fbdev client setup consists of the initial preparation and the
hot-plugging of the display. The latter creates the fbdev device
and sets up the fbdev framebuffer. The setup performs display
hot-plugging once. If no display can be detected, DRM probe helpers
re-run the detection on each hotplug event.
A call to drm_dev_unregister() releases the client automatically.
No further action is required within msm. If the fbdev framebuffer
has been fully set up, struct fb_ops.fb_destroy implements the
release. For partially initialized emulation, the fbdev client
reverts the initial setup.
v2:
* handle fbdev module parameter correctly (kernel test robot)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # RB5
Patchwork: https://patchwork.freedesktop.org/patch/530560/
Link: https://lore.kernel.org/r/20230403124538.8497-9-tzimmermann@suse.de
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
This reverts commit 8636500300.
A recent commit tried to address a drm device leak in the early
msm_drm_uninit() error paths but ended up making things worse.
Specifically, it moved the drm device reference put in msm_drm_uninit()
to msm_drm_init() which means that the drm would now be leaked on normal
unbind.
For reasons that were never spelled out, it also added kms NULL pointer
checks to a couple of helper functions that had nothing to do with the
paths modified by the patch.
Instead of trying to salvage this incrementally, let's revert the bad
commit so that clean and backportable fixes can be added in its place.
Fixes: 8636500300 ("drm/msm: Fix failure paths in msm_drm_init()")
Cc: Akhil P Oommen <quic_akhilpo@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/525092/
Link: https://lore.kernel.org/r/20230306100722.28485-3-johan+linaro@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
This reverts commit 643b7d0869.
A recent patch that tried to fix up the msm_drm_init() paths with
respect to the workqueue but only ended up making things worse:
First, the newly added calls to msm_drm_uninit() on early errors would
trigger NULL-pointer dereferences, for example, as the kms pointer would
not have been initialised. (Note that these paths were also modified by
a second broken error handling patch which in effect cancelled out this
part when merged.)
Second, the newly added allocation sanity check would still leak the
previously allocated drm device.
Instead of trying to salvage what was badly broken (and clearly not
tested), let's revert the bad commit so that clean and backportable
fixes can be added in its place.
Fixes: 643b7d0869 ("drm/msm: Add missing check and destroy for alloc_ordered_workqueue")
Cc: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/525107/
Link: https://lore.kernel.org/r/20230306100722.28485-2-johan+linaro@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
- Fix DPT+shmem combo and add i915.enable_dpt modparam (Ville)
- i915.enable_sagv module parameter (Ville)
- Correction to QGV related register addresses (Vinod)
- IPS debugfs per-crtc and new file for false_color (Ville)
- More clean-up and reorganization of Display code (Jani)
- DP DSC related fixes and improvements (Stanislav, Ankit, Suraj, Swati)
- Make utility pin asserts more accurate (Ville)
- Meteor Lake enabling (Daniele)
- High refresh rate PSR fixes (Jouni)
- Cursor and Plane chicken register fixes (Ville)
- Align the ADL-P TypeC sequences with hardware specification (Imre)
- Documentation build fixes and improvements to catch bugs earlier (Lee, Jani)
- PL1 power limit hwmon entry changed to use 0 as disabled state (Ashutosh)
- DP aux sync fix and improvements (Ville)
- DP MST fixes and w/a (Stanislav)
- Limit PXP drm-errors or warning on firmware API failures (Alan)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZC7RR3Laet8ywHRo@intel.com
drm/tegra: Changes for v6.4-rc1
The majority of this is minor cleanups and fixes. Other than those, this
contains Uwe's conversion to the new driver remove callback and Thomas'
fbdev DRM client conversion. The driver can now also be built on other
architectures to easy compile coverage.
Finally, this adds Mikko as a second maintainer for the driver. As a
next step we also want Tegra DRM to move into drm-misc to streamline the
maintenance process.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thierry Reding <thierry.reding@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230406121404.967704-1-thierry.reding@gmail.com
Move code from ad-hoc fbdev callbacks into DRM client functions
and remove the old callbacks. The functions instruct the client
to poll for changed output or restore the display. The DRM core
calls both, the old callbacks and the new client helpers, from
the same places. The new functions perform the same operation as
before, so there's no change in functionality.
Replace all code that initializes or releases fbdev emulation
throughout the driver. Instead initialize the fbdev client by a
single call to omapdrm_fbdev_setup() after omapdrm has registered
its DRM device. As in most drivers, omapdrm's fbdev emulation now
acts like a regular DRM client.
The fbdev client setup consists of the initial preparation and the
hot-plugging of the display. The latter creates the fbdev device
and sets up the fbdev framebuffer. The setup performs display
hot-plugging once. If no display can be detected, DRM probe helpers
re-run the detection on each hotplug event.
A call to drm_dev_unregister() releases the client automatically.
No further action is required within omapdrm. If the fbdev
framebuffer has been fully set up, struct fb_ops.fb_destroy
implements the release. For partially initialized emulation, the
fbdev client reverts the initial setup.
v2:
* init drm_client in this patch (Tomi)
* don't handle non-atomic modesetting (Tomi)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230403104035.15288-6-tzimmermann@suse.de
There's not much point in a static work function having a kernel-doc
comment. Just clean it up and make it a regular comment.
This fixes the kernel-doc warnings:
drivers/gpu/drm/i915/display/intel_tc.c:1370: warning: Function
parameter or member 'work' not described in
'intel_tc_port_disconnect_phy_work'
drivers/gpu/drm/i915/display/intel_tc.c:1370: warning: Excess function
parameter 'dig_port' description in 'intel_tc_port_disconnect_phy_work'
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Vinod Govindapillai <vinod.govindapillai@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230405104142.766598-1-jani.nikula@intel.com
drm-misc-next for v6.4-rc1:
UAPI Changes:
Cross-subsystem Changes:
- Document port and rotation dt bindings better.
- For panel timing DT bindings, document that vsync and hsync are
first, rather than last in image.
- Fix video/aperture typos.
Core Changes:
- Reject prime DMA-Buf attachment if get_sg_table is missing.
(For self-importing dma-buf only.)
- Add prime import/export to vram-helper.
- Fix oops in drm/vblank when init is not called.
- Fixup xres/yres_virtual and other fixes in fb helper.
- Improve SCDC debugs.
- Skip setting deadline on modesets.
- Assorted TTM fixes.
Driver Changes:
- Add lima usage stats.
- Assorted fixes to bridge/lt8192b, tc358767, ivpu,
bridge/ti-sn65dsi83, ps8640.
- Use pci aperture helpers in drm/ast lynxfb, radeonfb.
- Revert some lima patches, as they required a commit that has been
reverted upstream.
- Add AUO NE135FBM-N41 v8.1 eDP panel.
- Add QAIC accel driver.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/64bb9696-a76a-89d9-1866-bcdf7c69c284@linux.intel.com
UAPI Changes:
- (Build-time only, should not have any impact)
drm/i915/uapi: Replace fake flex-array with flexible-array member
"Zero-length arrays as fake flexible arrays are deprecated and we are
moving towards adopting C99 flexible-array members instead."
This is on core kernel request moving towards GCC 13.
Driver Changes:
- Fix context runtime accounting on sysfs fdinfo for heavy workloads (Tvrtko)
- Add support for OA media units on MTL (Umesh)
- Add new workarounds for Meteorlake (Daniele, Radhakrishna, Haridhar)
- Fix sysfs to read actual frequency for MTL and Gen6 and earlier
(Ashutosh)
- Synchronize i915/BIOS on C6 enabling on MTL (Vinay)
- Fix DMAR error noise due to GPU error capture (Andrej)
- Fix forcewake during BAR resize on discrete (Andrzej)
- Flush lmem contents after construction on discrete (Chris)
- Fix GuC loading timeout on systems where IFWI programs low boot
frequency (John)
- Fix race condition UAF in i915_perf_add_config_ioctl (Min)
- Sanitycheck MMIO access early in driver load and during forcewake
(Matt)
- Wakeref fixes for GuC RC error scenario and active VM tracking (Chris)
- Cancel HuC delayed load timer on reset (Daniele)
- Limit double GT reset to pre-MTL (Daniele)
- Use i915 instead of dev_priv insied the file_priv structure (Andi)
- Improve GuC load error reporting (John)
- Simplify VCS/BSD engine selection logic (Tvrtko)
- Perform uc late init after probe error injection (Andrzej)
- Fix format for perf_limit_reasons in debugfs (Vinay)
- Create per-gt debugfs files (Andi)
- Documentation and kerneldoc fixes (Nirmoy, Lee)
- Selftest improvements (Fei, Jonathan)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZC6APj/feB+jBf2d@jlahtine-mobl.ger.corp.intel.com
Before commit bc0d7fdefe ("drm: vkms: Supports to the case where
primary plane doesn't match the CRTC"), the composition was executed
on top of the primary plane. Therefore, the primary plane needed to cover
the entire CRTC. After commit bc0d7fdefe, this is no longer necessary,
as the composition is now executed on top of the CRTC.
Then, allow the primary plane to be positioned in such a way that it
doesn't cover the entire CRTC.
This patch was tested with the vkms IGT testlist and all tests passed
successfully. Moreover, the test
igt@kms_universal_plane@universal-plane-pageflip-windowed-pipe-A
used to fail and now is passing.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230324164226.256084-3-mcanal@igalia.com
Before commit bc0d7fdefe ("drm: vkms: Supports to the case where
primary plane doesn't match the CRTC"), the composition was executed on
top of the primary plane. Therefore, the primary plane needed to be
visible and full screen. After commit bc0d7fdefe, this is no longer
necessary, as the composition is now executed on top of the CRTC.
Then, remove the conditional expression that forced the primary plane to
be visible and full screen. This allows vkms to accept non-null
framebuffers when the CRTC is disabled.
This patch was tested with the vkms IGT testlist and all tests passed
successfully. Moreover, the tests
igt@kms_universal_plane@universal-plane-pipe-a-functional and
igt@kms_universal_plane@disable-primary-vs-flip-pipe-a used to fail and
now are passing.
Signed-off-by: Maíra Canal <mcanal@igalia.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20230324164226.256084-2-mcanal@igalia.com
In tegra_sor_compute_config(), the 32-bit value mode->clock is
multiplied by 1000, and assigned to the u64 variable pclk. We can avoid
a potential 32-bit integer overflow by casting mode->clock to u64 before
we do the arithmetic and assignment.
Signed-off-by: Nur Hussein <hussein@unixcat.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move code from ad-hoc fbdev callbacks into DRM client functions
and remove the old callbacks. The functions instruct the client
to poll for changed output or restore the display. The DRM core
calls both, the old callbacks and the new client helpers, from
the same places. The new functions perform the same operation as
before, so there's no change in functionality.
Replace all code that initializes or releases fbdev emulation
throughout the driver. Instead initialize the fbdev client by a
single call to tegra_fbdev_setup() after tegra has registered
its DRM device. As in most drivers, tegra's fbdev emulation now
acts like a regular DRM client.
The fbdev client setup consists of the initial preparation and the
hot-plugging of the display. The latter creates the fbdev device
and sets up the fbdev framebuffer. The setup performs display
hot-plugging once. If no display can be detected, DRM probe helpers
re-run the detection on each hotplug event.
A call to drm_dev_unregister() releases the client automatically.
No further action is required within tegra. If the fbdev
framebuffer has been fully set up, struct fb_ops.fb_destroy
implements the release. For partially initialized emulation, the
fbdev client reverts the initial setup.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Initialize the fbdev client in the fbdev code with empty helper
functions. Also clean up the client. The helpers will later
implement various functionality of the DRM client. No functional
changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Only build tegra's fbdev emulation if CONFIG_DRM_FBDEV_EMULATION
has been enabled. As part of this change, move the code into its
own source file. No functional changes.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
