Using netconsole netpoll_poll_dev could be called from interrupt
context, thus using disable_irq() would cause the following kernel
warning with CONFIG_DEBUG_ATOMIC_SLEEP enabled:
BUG: sleeping function called from invalid context at kernel/irq/manage.c:137
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 10, name: ksoftirqd/0
CPU: 0 PID: 10 Comm: ksoftirqd/0 Tainted: G W 5.15.42-00075-g816b502b2298-dirty #117
Hardware name: aml (r1) (DT)
Call trace:
dump_backtrace+0x0/0x270
show_stack+0x14/0x20
dump_stack_lvl+0x8c/0xac
dump_stack+0x18/0x30
___might_sleep+0x150/0x194
__might_sleep+0x64/0xbc
synchronize_irq+0x8c/0x150
disable_irq+0x2c/0x40
stmmac_poll_controller+0x140/0x1a0
netpoll_poll_dev+0x6c/0x220
netpoll_send_skb+0x308/0x390
netpoll_send_udp+0x418/0x760
write_msg+0x118/0x140 [netconsole]
console_unlock+0x404/0x500
vprintk_emit+0x118/0x250
dev_vprintk_emit+0x19c/0x1cc
dev_printk_emit+0x90/0xa8
__dev_printk+0x78/0x9c
_dev_warn+0xa4/0xbc
ath10k_warn+0xe8/0xf0 [ath10k_core]
ath10k_htt_txrx_compl_task+0x790/0x7fc [ath10k_core]
ath10k_pci_napi_poll+0x98/0x1f4 [ath10k_pci]
__napi_poll+0x58/0x1f4
net_rx_action+0x504/0x590
_stext+0x1b8/0x418
run_ksoftirqd+0x74/0xa4
smpboot_thread_fn+0x210/0x3c0
kthread+0x1fc/0x210
ret_from_fork+0x10/0x20
Since [0] .ndo_poll_controller is only needed if driver doesn't or
partially use NAPI. Because stmmac does so, stmmac_poll_controller
can be removed fixing the above warning.
[0] commit ac3d9dd034 ("netpoll: make ndo_poll_controller() optional")
Cc: <stable@vger.kernel.org> # 5.15.x
Fixes: 47dd7a540b ("net: add support for STMicroelectronics Ethernet controllers")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/1c156a6d8c9170bd6a17825f2277115525b4d50f.1696429960.git.repk@triplefau.lt
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While searching for possible refactor of napi_schedule_prep and
__napi_schedule it was notice that the mtk eth driver disable the
interrupt for rx and tx AFTER napi is scheduled.
While this is a very hard to repro case it might happen to have
situation where the interrupt is disabled and never enabled again as the
napi completes and the interrupt is enabled before.
This is caused by the fact that a napi driven by interrupt expect a
logic with:
1. interrupt received. napi prepared -> interrupt disabled -> napi
scheduled
2. napi triggered. ring cleared -> interrupt enabled -> wait for new
interrupt
To prevent this case, disable the interrupt BEFORE the napi is
scheduled.
Fixes: 656e705243 ("net-next: mediatek: add support for MT7623 ethernet")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20231002140805.568-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Handle the case when GSO SKB linear length is too large.
MANA NIC requires GSO packets to put only the header part to SGE0,
otherwise the TX queue may stop at the HW level.
So, use 2 SGEs for the skb linear part which contains more than the
packet header.
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
For an unknown TX CQE error type (probably from a newer hardware),
still free the SKB, update the queue tail, etc., otherwise the
accounting will be wrong.
Also, TX errors can be triggered by injecting corrupted packets, so
replace the WARN_ONCE to ratelimited error logging.
Cc: stable@vger.kernel.org
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The STM32MP1 keeps clk_rx enabled during suspend, and therefore the
driver does not enable the clock in stm32_dwmac_init() if the device was
suspended. The problem is that this same code runs on STM32 MCUs, which
do disable clk_rx during suspend, causing the clock to never be
re-enabled on resume.
This patch adds a variant flag to indicate that clk_rx remains enabled
during suspend, and uses this to decide whether to enable the clock in
stm32_dwmac_init() if the device was suspended.
This approach fixes this specific bug with limited opportunity for
unintended side-effects, but I have a follow up patch that will refactor
the clock configuration and hopefully make it less error prone.
Fixes: 6528e02cc9 ("net: ethernet: stmmac: add adaptation for stm32mp157c.")
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230927175749.1419774-1-ben.wolsieffer@hefring.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Johannes Berg says:
====================
Quite a collection of fixes this time, really too many
to list individually. Many stack fixes, even rfkill
(found by simulation and the new eevdf scheduler)!
Also a bigger maintainers file cleanup, to remove old
and redundant information.
* tag 'wireless-2023-09-27' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless: (32 commits)
wifi: iwlwifi: mvm: Fix incorrect usage of scan API
wifi: mac80211: Create resources for disabled links
wifi: cfg80211: avoid leaking stack data into trace
wifi: mac80211: allow transmitting EAPOL frames with tainted key
wifi: mac80211: work around Cisco AP 9115 VHT MPDU length
wifi: cfg80211: Fix 6GHz scan configuration
wifi: mac80211: fix potential key leak
wifi: mac80211: fix potential key use-after-free
wifi: mt76: mt76x02: fix MT76x0 external LNA gain handling
wifi: brcmfmac: Replace 1-element arrays with flexible arrays
wifi: mwifiex: Fix oob check condition in mwifiex_process_rx_packet
wifi: rtw88: rtw8723d: Fix MAC address offset in EEPROM
rfkill: sync before userspace visibility/changes
wifi: mac80211: fix mesh id corruption on 32 bit systems
wifi: cfg80211: add missing kernel-doc for cqm_rssi_work
wifi: cfg80211: fix cqm_config access race
wifi: iwlwifi: mvm: Fix a memory corruption issue
wifi: iwlwifi: Ensure ack flag is properly cleared.
wifi: iwlwifi: dbg_ini: fix structure packing
iwlwifi: mvm: handle PS changes in vif_cfg_changed
...
====================
Link: https://lore.kernel.org/r/20230927095835.25803-2-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In some OVS environments the TCP pseudo header checksum may need to be
recomputed. Currently this is only done when the interface instance is
configured for "Trunk Mode". We found the issue also occurs in some
Kubernetes environments, these environments do not use "Trunk Mode",
therefor the condition is removed.
Performance tests with this change show only a fractional decrease in
throughput (< 0.2%).
Fixes: 7525de2516 ("ibmveth: Set CHECKSUM_PARTIAL if NULL TCP CSUM.")
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Reviewed-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The k3_udma_glue_tx_get_irq() function currently returns negative error
codes on error, zero on error and positive values for success. This
complicates life for the callers who need to propagate the error code.
Also GCC will not warn about unsigned comparisons when you check:
if (unsigned_irq <= 0)
All the callers have been fixed now but let's just make this easy going
forward.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "tx_chn->irq" variable is unsigned so the error checking does not
work correctly.
Fixes: 128d5874c0 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This accidentally returns success, but it should return a negative error
code.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the MPIC.PSMCS value following the programming example in the
section 6.4.2 Management Data Clock (MDC) Setting, Ethernet MAC IP,
S4 Hardware User Manual Rev.1.00.
The value is calculated by
MPIC.PSMCS = clk[MHz] / (MDC frequency[MHz] * 2) - 1
with the input clock frequency from clk_get_rate() and MDC frequency
of 2.5MHz. Otherwise, this driver cannot communicate PHYs on the R-Car
S4 Starter Kit board.
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Reported-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230926123054.3976752-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The flexible structure (a structure that contains a flexible-array member
at the end) `qed_ll2_tx_packet` is nested within the second layer of
`struct qed_ll2_info`:
struct qed_ll2_tx_packet {
...
/* Flexible Array of bds_set determined by max_bds_per_packet */
struct {
struct core_tx_bd *txq_bd;
dma_addr_t tx_frag;
u16 frag_len;
} bds_set[];
};
struct qed_ll2_tx_queue {
...
struct qed_ll2_tx_packet cur_completing_packet;
};
struct qed_ll2_info {
...
struct qed_ll2_tx_queue tx_queue;
struct qed_ll2_cbs cbs;
};
The problem is that member `cbs` in `struct qed_ll2_info` is placed just
after an object of type `struct qed_ll2_tx_queue`, which is in itself
an implicit flexible structure, which by definition ends in a flexible
array member, in this case `bds_set`. This causes an undefined behavior
bug at run-time when dynamic memory is allocated for `bds_set`, which
could lead to a serious issue if `cbs` in `struct qed_ll2_info` is
overwritten by the contents of `bds_set`. Notice that the type of `cbs`
is a structure full of function pointers (and a cookie :) ):
include/linux/qed/qed_ll2_if.h:
107 typedef
108 void (*qed_ll2_complete_rx_packet_cb)(void *cxt,
109 struct qed_ll2_comp_rx_data *data);
110
111 typedef
112 void (*qed_ll2_release_rx_packet_cb)(void *cxt,
113 u8 connection_handle,
114 void *cookie,
115 dma_addr_t rx_buf_addr,
116 bool b_last_packet);
117
118 typedef
119 void (*qed_ll2_complete_tx_packet_cb)(void *cxt,
120 u8 connection_handle,
121 void *cookie,
122 dma_addr_t first_frag_addr,
123 bool b_last_fragment,
124 bool b_last_packet);
125
126 typedef
127 void (*qed_ll2_release_tx_packet_cb)(void *cxt,
128 u8 connection_handle,
129 void *cookie,
130 dma_addr_t first_frag_addr,
131 bool b_last_fragment, bool b_last_packet);
132
133 typedef
134 void (*qed_ll2_slowpath_cb)(void *cxt, u8 connection_handle,
135 u32 opaque_data_0, u32 opaque_data_1);
136
137 struct qed_ll2_cbs {
138 qed_ll2_complete_rx_packet_cb rx_comp_cb;
139 qed_ll2_release_rx_packet_cb rx_release_cb;
140 qed_ll2_complete_tx_packet_cb tx_comp_cb;
141 qed_ll2_release_tx_packet_cb tx_release_cb;
142 qed_ll2_slowpath_cb slowpath_cb;
143 void *cookie;
144 };
Fix this by moving the declaration of `cbs` to the middle of its
containing structure `qed_ll2_info`, preventing it from being
overwritten by the contents of `bds_set` at run-time.
This bug was introduced in 2017, when `bds_set` was converted to a
one-element array, and started to be used as a Variable Length Object
(VLO) at run-time.
Fixes: f5823fe689 ("qed: Add ll2 option to limit the number of bds per packet")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/ZQ+Nz8DfPg56pIzr@work
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In the pathological case of building sky2 with 16k PAGE_SIZE, the
frag_addr[] array would never be used, so the original code was correct
that size should be 0. But the compiler now gets upset with 0 size arrays
in places where it hasn't eliminated the code that might access such an
array (it can't figure out that in this case an rx skb with fragments
would never be created). To keep the compiler happy, make sure there is
at least 1 frag_addr in struct rx_ring_info:
In file included from include/linux/skbuff.h:28,
from include/net/net_namespace.h:43,
from include/linux/netdevice.h:38,
from drivers/net/ethernet/marvell/sky2.c:18:
drivers/net/ethernet/marvell/sky2.c: In function 'sky2_rx_unmap_skb':
include/linux/dma-mapping.h:416:36: warning: array subscript i is outside array bounds of 'dma_addr_t[0]' {aka 'long long unsigned int[]'} [-Warray-bounds=]
416 | #define dma_unmap_page(d, a, s, r) dma_unmap_page_attrs(d, a, s, r, 0)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/marvell/sky2.c:1257:17: note: in expansion of macro 'dma_unmap_page'
1257 | dma_unmap_page(&pdev->dev, re->frag_addr[i],
| ^~~~~~~~~~~~~~
In file included from drivers/net/ethernet/marvell/sky2.c:41:
drivers/net/ethernet/marvell/sky2.h:2198:25: note: while referencing 'frag_addr'
2198 | dma_addr_t frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
| ^~~~~~~~~
With CONFIG_PAGE_SIZE_16KB=y, PAGE_SHIFT == 14, so:
#define ETH_JUMBO_MTU 9000
causes "ETH_JUMBO_MTU >> PAGE_SHIFT" to be 0. Use "?: 1" to solve this build warning.
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309191958.UBw1cjXk-lkp@intel.com/
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 23d775f12d ("net: dsa: mv88e6xxx: Wait for EEPROM done
before HW reset") the following error is seen on a imx8mn board with
a 88E6320 switch:
mv88e6085 30be0000.ethernet-1:00: Timeout waiting for EEPROM done
This board does not have an EEPROM attached to the switch though.
This problem is well explained by Andrew Lunn:
"If there is an EEPROM, and the EEPROM contains a lot of data, it could
be that when we perform a hardware reset towards the end of probe, it
interrupts an I2C bus transaction, leaving the I2C bus in a bad state,
and future reads of the EEPROM do not work.
The work around for this was to poll the EEInt status and wait for it
to go true before performing the hardware reset.
However, we have discovered that for some boards which do not have an
EEPROM, EEInt never indicates complete. As a result,
mv88e6xxx_g1_wait_eeprom_done() spins for a second and then prints a
warning.
We probably need a different solution than calling
mv88e6xxx_g1_wait_eeprom_done(). The datasheet for 6352 documents the
EEPROM Command register:
bit 15 is:
EEPROM Unit Busy. This bit must be set to a one to start an EEPROM
operation (see EEOp below). Only one EEPROM operation can be
executing at one time so this bit must be zero before setting it to
a one. When the requested EEPROM operation completes this bit will
automatically be cleared to a zero. The transition of this bit from
a one to a zero can be used to generate an interrupt (the EEInt in
Global 1, offset 0x00).
and more interesting is bit 11:
Register Loader Running. This bit is set to one whenever the
register loader is busy executing instructions contained in the
EEPROM."
Change to using mv88e6xxx_g2_eeprom_wait() to fix the timeout error
when the EEPROM chip is not present.
Fixes: 23d775f12d ("net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PF and VF drivers both support flexible rx descriptors and have
negotiated the VIRTCHNL_VF_OFFLOAD_RX_FLEX_DESC capability, the VF driver
queries the PF for the list of supported descriptor formats
(VIRTCHNL_OP_GET_SUPPORTED_RXDIDS). The PF driver is supposed to set the
supported_rxdids bits that correspond to the descriptor formats the
firmware implements. The legacy 32-byte rx desc format is always
supported, even though it is not expressed in GLFLXP_RXDID_FLAGS.
The ice driver does not advertise the legacy 32-byte rx desc support,
which leads to this failure to bring up the VF using the Intel
out-of-tree iavf driver:
iavf 0000:41:01.0: PF does not list support for default Rx descriptor format
...
iavf 0000:41:01.0: PF returned error -5 (VIRTCHNL_STATUS_ERR_PARAM) to our request 6
The in-tree iavf driver does not expose this bug, because it does not
yet implement VIRTCHNL_VF_OFFLOAD_RX_FLEX_DESC.
The ice driver must always set the ICE_RXDID_LEGACY_1 bit in
supported_rxdids. The Intel out-of-tree ice driver and the ice driver in
DPDK both do this.
I copied this piece of the code and the comment text from the Intel
out-of-tree driver.
Fixes: e753df8fbc ("ice: Add support Flex RXD")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20230920115439.61172-1-mschmidt@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Process the result of hdlc_open() and call uhdlc_close()
in case of an error. It is necessary to pass the error
code up the control flow, similar to a possible
error in request_irq().
Also add a hdlc_close() call to the uhdlc_close()
because the comment to hdlc_close() says it must be called
by the hardware driver when the HDLC device is being closed
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: c19b6d246a ("drivers/net: support hdlc function for QE-UCC")
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several places in TC offload code assumed that the return from
rhashtable_lookup_get_insert_fast() was always either NULL or a valid
pointer to an existing entry, but in fact that function can return an
error pointer. In that case, perform the usual cleanup of the newly
created entry, then pass up the error, rather than attempting to take a
reference on the old entry.
Fixes: d902e1a737 ("sfc: bare bones TC offload on EF100")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20230919183949.59392-1-edward.cree@amd.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When users attempt to obtain the coalesce setting using the
ethtool command, current code always returns 0 for tx-usecs.
This is because I225/6 always uses a queue pair setting, hence
tx_coalesce_usecs does not return a value during the
igc_ethtool_get_coalesce() callback process. The pair queue
condition checking in igc_ethtool_get_coalesce() is removed by
this patch so that the user gets information of the value of tx-usecs.
Even if i225/6 is using queue pair setting, there is no harm in
notifying the user of the tx-usecs. The implementation of the current
code may have previously been a copy of the legacy code i210.
Since I225 has the queue pair setting enabled, tx-usecs will always adhere
to the user-set rx-usecs value. An error message will appear when the user
attempts to set the tx-usecs value for the input parameters because,
by default, they should only set the rx-usecs value.
This patch also adds the helper function to get the
previous rx coalesce value similar to tx coalesce.
How to test:
User can get the coalesce value using ethtool command.
Example command:
Get: ethtool -c <interface>
Previous output:
rx-usecs: 3
rx-frames: n/a
rx-usecs-irq: n/a
rx-frames-irq: n/a
tx-usecs: 0
tx-frames: n/a
tx-usecs-irq: n/a
tx-frames-irq: n/a
New output:
rx-usecs: 3
rx-frames: n/a
rx-usecs-irq: n/a
rx-frames-irq: n/a
tx-usecs: 3
tx-frames: n/a
tx-usecs-irq: n/a
tx-frames-irq: n/a
Fixes: 8c5ad0dae9 ("igc: Add ethtool support")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230919170331.1581031-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
bnxt_poll_nitroa0() invokes bnxt_rx_pkt() which can run a XDP program
which in turn can return XDP_REDIRECT. bnxt_rx_pkt() is also used by
__bnxt_poll_work() which flushes (xdp_do_flush()) the packets after each
round. bnxt_poll_nitroa0() lacks this feature.
xdp_do_flush() should be invoked before leaving the NAPI callback.
Invoke xdp_do_flush() after a redirect in bnxt_poll_nitroa0() NAPI.
Cc: Michael Chan <michael.chan@broadcom.com>
Fixes: f18c2b77b2 ("bnxt_en: optimized XDP_REDIRECT support")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
xdp_do_flush() should be invoked before leaving the NAPI poll function
after a XDP-redirect. This is not the case if the driver leaves via
the error path (after having a redirect in one of its previous
iterations).
Invoke xdp_do_flush() also in the error path.
Cc: Arthur Kiyanovski <akiyano@amazon.com>
Cc: David Arinzon <darinzon@amazon.com>
Cc: Noam Dagan <ndagan@amazon.com>
Cc: Saeed Bishara <saeedb@amazon.com>
Cc: Shay Agroskin <shayagr@amazon.com>
Fixes: a318c70ad1 ("net: ena: introduce XDP redirect implementation")
Acked-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are some attributes added by vxlan_fill_info() which are not
accounted for in vxlan_get_size(). Add them.
I didn't find a way to trigger an actual problem from this miscalculation
since there is usually extra space in netlink size calculations like
if_nlmsg_size(); but maybe I just didn't search long enough.
Fixes: 3511494ce2 ("vxlan: Group Policy extension")
Fixes: e1e5314de0 ("vxlan: implement GPE")
Fixes: 0ace2ca89c ("vxlan: Use checksum partial with remote checksum offload")
Fixes: f9c4bb0b24 ("vxlan: vni filtering support on collect metadata device")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get a null-ptr-deref bug as follows with reproducer [1].
BUG: kernel NULL pointer dereference, address: 0000000000000228
...
RIP: 0010:vlan_dev_hard_header+0x35/0x140 [8021q]
...
Call Trace:
<TASK>
? __die+0x24/0x70
? page_fault_oops+0x82/0x150
? exc_page_fault+0x69/0x150
? asm_exc_page_fault+0x26/0x30
? vlan_dev_hard_header+0x35/0x140 [8021q]
? vlan_dev_hard_header+0x8e/0x140 [8021q]
neigh_connected_output+0xb2/0x100
ip6_finish_output2+0x1cb/0x520
? nf_hook_slow+0x43/0xc0
? ip6_mtu+0x46/0x80
ip6_finish_output+0x2a/0xb0
mld_sendpack+0x18f/0x250
mld_ifc_work+0x39/0x160
process_one_work+0x1e6/0x3f0
worker_thread+0x4d/0x2f0
? __pfx_worker_thread+0x10/0x10
kthread+0xe5/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
[1]
$ teamd -t team0 -d -c '{"runner": {"name": "loadbalance"}}'
$ ip link add name t-dummy type dummy
$ ip link add link t-dummy name t-dummy.100 type vlan id 100
$ ip link add name t-nlmon type nlmon
$ ip link set t-nlmon master team0
$ ip link set t-nlmon nomaster
$ ip link set t-dummy up
$ ip link set team0 up
$ ip link set t-dummy.100 down
$ ip link set t-dummy.100 master team0
When enslave a vlan device to team device and team device type is changed
from non-ether to ether, header_ops of team device is changed to
vlan_header_ops. That is incorrect and will trigger null-ptr-deref
for vlan->real_dev in vlan_dev_hard_header() because team device is not
a vlan device.
Cache eth_header_ops in team_setup(), then assign cached header_ops to
header_ops of team net device when its type is changed from non-ether
to ether to fix the bug.
Fixes: 1d76efe157 ("team: add support for non-ethernet devices")
Suggested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230918123011.1884401-1-william.xuanziyang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently the reset process in hns3 and firmware watchdog init process is
asynchronous. we think firmware watchdog initialization is completed
before hns3 clear the firmware interrupt source. However, firmware
initialization may not complete early.
so we add delay before hns3 clear firmware interrupt source and 5 ms delay
is enough to avoid second firmware reset interrupt.
Fixes: c1a81619d7 ("net: hns3: Add mailbox interrupt handling to PF driver")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Firmware does not respond driver commands during reset
Therefore, rule will fail to delete while the firmware is resetting
So, if failed to delete rule, set rule state to TO_DEL,
and the rule will be deleted when periodic task being scheduled.
Fixes: 0205ec041e ("net: hns3: add support for hw tc offload of tc flower")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently, the driver will enable unicast promisc for the function
once configure mac address fail. It's unreasonable when the failure
is caused by using same mac address with other functions. So only
enable unicast promisc when mac table full.
Fixes: c631c69682 ("net: hns3: refactor the promisc mode setting")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The device_version V3 hardware can't offload the checksum for IP in GRE
packets, but can do it for NvGRE. So default to disable the checksum and
GSO offload for GRE, but keep the ability to enable it when only using
NvGRE.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When the vf cmdq is disabled, there is no need to keep these task running.
So this patch skip these task when the cmdq is disabled.
Fixes: ff200099d2 ("net: hns3: remove unnecessary work in hclgevf_main")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
commit 133466c3bb ("net: stmmac: use per-queue 64 bit statistics
where necessary") caused one regression as found by Uwe, the backtrace
looks like:
INFO: trying to register non-static key.
The code is fine but needs lockdep annotation, or maybe
you didn't initialize this object before use?
turning off the locking correctness validator.
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.5.0-rc1-00449-g133466c3bbe1-dirty #21
Hardware name: STM32 (Device Tree Support)
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x60/0x90
dump_stack_lvl from register_lock_class+0x98c/0x99c
register_lock_class from __lock_acquire+0x74/0x293c
__lock_acquire from lock_acquire+0x134/0x398
lock_acquire from stmmac_get_stats64+0x2ac/0x2fc
stmmac_get_stats64 from dev_get_stats+0x44/0x130
dev_get_stats from rtnl_fill_stats+0x38/0x120
rtnl_fill_stats from rtnl_fill_ifinfo+0x834/0x17f4
rtnl_fill_ifinfo from rtmsg_ifinfo_build_skb+0xc0/0x144
rtmsg_ifinfo_build_skb from rtmsg_ifinfo+0x50/0x88
rtmsg_ifinfo from __dev_notify_flags+0xc0/0xec
__dev_notify_flags from dev_change_flags+0x50/0x5c
dev_change_flags from ip_auto_config+0x2f4/0x1260
ip_auto_config from do_one_initcall+0x70/0x35c
do_one_initcall from kernel_init_freeable+0x2ac/0x308
kernel_init_freeable from kernel_init+0x1c/0x138
kernel_init from ret_from_fork+0x14/0x2c
The reason is the rxq|txq_stats structures are not what expected
because stmmac_open() -> __stmmac_open() the structure is overwritten
by "memcpy(&priv->dma_conf, dma_conf, sizeof(*dma_conf));"
This causes the well initialized syncp member of rxq|txq_stats is
overwritten unexpectedly as pointed out by Johannes and Uwe.
Fix this issue by moving rxq|txq_stats back to stmmac_extra_stats. For
SMP cache friendly, we also mark stmmac_txq_stats and stmmac_rxq_stats
as ____cacheline_aligned_in_smp.
Fixes: 133466c3bb ("net: stmmac: use per-queue 64 bit statistics where necessary")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230917165328.3403-1-jszhang@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Since commit 2d47c6956a ("ubsan: Tighten UBSAN_BOUNDS on GCC"),
UBSAN_BOUNDS no longer pretends 1-element arrays are unbounded. Walking
'element' and 'channel_list' will trigger warnings, so make them proper
flexible arrays.
False positive warnings were:
UBSAN: array-index-out-of-bounds in drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:6984:20
index 1 is out of range for type '__le32 [1]'
UBSAN: array-index-out-of-bounds in drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c:1126:27
index 1 is out of range for type '__le16 [1]'
for these lines of code:
6884 ch.chspec = (u16)le32_to_cpu(list->element[i]);
1126 params_le->channel_list[i] = cpu_to_le16(chanspec);
Cc: stable@vger.kernel.org # 6.5+
Signed-off-by: Juerg Haefliger <juerg.haefliger@canonical.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230914070227.12028-1-juerg.haefliger@canonical.com
According to the NAPI documentation networking/napi.rst, Rx specific
APIs like page pool and XDP cannot be used at all when budget is 0.
skb Tx processing should happen regardless of the budget.
Stop NAPI polling after Tx processing and skip Rx processing if budget
is 0.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the NAPI documentation networking/napi.rst, for the ethtool
API a channel is a IRQ/NAPI which services queues of a given type.
tsnep uses a single IRQ/NAPI instance for every TX/RX queue pair.
Therefore, combined channels shall be returned instead of separate tx/rx
channels.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the NAPI documentation networking/napi.rst, drivers which
have to mask interrupts explicitly should use the napi_schedule_prep()
and __napi_schedule() calls.
No problem seen so far with current implementation. Nevertheless, let's
align the implementation with documentation.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
queue
Tony Nguyen says:
====================
This series contains updates to iavf and i40e drivers.
Radoslaw prevents admin queue operations being added when the driver is
being removed for iavf.
Petr Oros immediately starts reconfiguration on changes to VLANs on
iavf.
Ivan Vecera moves reset of VF to occur after port VLAN values are set
on i40e.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When an XDP redirect happens before the link is ready, that
transmission will not finish and will timeout, causing an adapter
reset. If the redirects do not stop, the adapter will not stop
resetting.
Wait for the driver to signal that there's a carrier before allowing
transmissions to proceed.
Previous code was relying that when __IGC_DOWN is cleared, the NIC is
ready to transmit as all the queues are ready, what happens is that
the carrier presence will only be signaled later, after the watchdog
workqueue has a chance to run. And during this interval (between
clearing __IGC_DOWN and the watchdog running) if any transmission
happens the timeout is emitted (detected by igc_tx_timeout()) which
causes the reset, with the potential for the infinite loop.
Fixes: 4ff3203610 ("igc: Add support for XDP_REDIRECT action")
Reported-by: Ferenc Fejes <ferenc.fejes@ericsson.com>
Closes: https://lore.kernel.org/netdev/0caf33cf6adb3a5bf137eeaa20e89b167c9986d5.camel@ericsson.com/
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Ferenc Fejes <ferenc.fejes@ericsson.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ionic device supports a maximum buffer length of 16 bits (see
ionic_rxq_desc or ionic_rxq_sg_elem). When adding new buffers to
the receive rings, the function ionic_rx_fill() uses 16bit math when
calculating the number of pages to allocate for an RX descriptor,
given the interface's MTU setting. If the system PAGE_SIZE >= 64KB,
and the buf_info->page_offset is 0, the remain_len value will never
decrement from the original MTU value and the frag_len value will
always be 0, causing additional pages to be allocated as scatter-
gather elements unnecessarily.
A similar math issue exists in ionic_rx_frags(), but no failures
have been observed here since a 64KB page should not normally
require any scatter-gather elements at any legal Ethernet MTU size.
Fixes: 4b0a7539a3 ("ionic: implement Rx page reuse")
Signed-off-by: David Christensen <drc@linux.vnet.ibm.com>
Reviewed-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If port VLAN is configured on a VF then any other VLANs on top of this VF
are broken.
During i40e_ndo_set_vf_port_vlan() call the i40e driver reset the VF and
iavf driver asks PF (using VIRTCHNL_OP_GET_VF_RESOURCES) for VF capabilities
but this reset occurs too early, prior setting of vf->info.pvid field
and because this field can be zero during i40e_vc_get_vf_resources_msg()
then VIRTCHNL_VF_OFFLOAD_VLAN capability is reported to iavf driver.
This is wrong because iavf driver should not report VLAN offloading
capability when port VLAN is configured as i40e does not support QinQ
offloading.
Fix the issue by moving VF reset after setting of vf->port_vlan_id
field.
Without this patch:
$ echo 1 > /sys/class/net/enp2s0f0/device/sriov_numvfs
$ ip link set enp2s0f0 vf 0 vlan 3
$ ip link set enp2s0f0v0 up
$ ip link add link enp2s0f0v0 name vlan4 type vlan id 4
$ ip link set vlan4 up
...
$ ethtool -k enp2s0f0v0 | grep vlan-offload
rx-vlan-offload: on
tx-vlan-offload: on
$ dmesg -l err | grep iavf
[1292500.742914] iavf 0000:02:02.0: Failed to add VLAN filter, error IAVF_ERR_INVALID_QP_ID
With this patch:
$ echo 1 > /sys/class/net/enp2s0f0/device/sriov_numvfs
$ ip link set enp2s0f0 vf 0 vlan 3
$ ip link set enp2s0f0v0 up
$ ip link add link enp2s0f0v0 name vlan4 type vlan id 4
$ ip link set vlan4 up
...
$ ethtool -k enp2s0f0v0 | grep vlan-offload
rx-vlan-offload: off [requested on]
tx-vlan-offload: off [requested on]
$ dmesg -l err | grep iavf
Fixes: f9b4b6278d ("i40e: Reset the VF upon conflicting VLAN configuration")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the iavf driver wants to reconfigure the VLAN filters
(iavf_add_vlan, iavf_del_vlan), it sets a flag in
aq_required:
adapter->aq_required |= IAVF_FLAG_AQ_ADD_VLAN_FILTER;
or:
adapter->aq_required |= IAVF_FLAG_AQ_DEL_VLAN_FILTER;
This is later processed by the watchdog_task, but it runs periodically
every 2 seconds, so it can be a long time before it processes the request.
In the worst case, the interface is unable to receive traffic for more
than 2 seconds for no objective reason.
Fixes: 5eae00c57f ("i40evf: main driver core")
Signed-off-by: Petr Oros <poros@redhat.com>
Co-developed-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Co-developed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Prevent schedule operations for adminq during device remove and when
__IAVF_IN_REMOVE_TASK flag is set. Currently, the iavf_down function
adds operations for adminq that shouldn't be processed when the device
is in the __IAVF_REMOVE state.
Reproduction:
echo 4 > /sys/bus/pci/devices/0000:17:00.0/sriov_numvfs
ip link set dev ens1f0 vf 0 trust on
ip link set dev ens1f0 vf 1 trust on
ip link set dev ens1f0 vf 2 trust on
ip link set dev ens1f0 vf 3 trust on
ip link set dev ens1f0 vf 0 mac 00:22:33:44:55:66
ip link set dev ens1f0 vf 1 mac 00:22:33:44:55:67
ip link set dev ens1f0 vf 2 mac 00:22:33:44:55:68
ip link set dev ens1f0 vf 3 mac 00:22:33:44:55:69
echo 0000:17:02.0 > /sys/bus/pci/devices/0000\:17\:02.0/driver/unbind
echo 0000:17:02.1 > /sys/bus/pci/devices/0000\:17\:02.1/driver/unbind
echo 0000:17:02.2 > /sys/bus/pci/devices/0000\:17\:02.2/driver/unbind
echo 0000:17:02.3 > /sys/bus/pci/devices/0000\:17\:02.3/driver/unbind
sleep 10
echo 0000:17:02.0 > /sys/bus/pci/drivers/iavf/bind
echo 0000:17:02.1 > /sys/bus/pci/drivers/iavf/bind
echo 0000:17:02.2 > /sys/bus/pci/drivers/iavf/bind
echo 0000:17:02.3 > /sys/bus/pci/drivers/iavf/bind
modprobe vfio-pci
echo 8086 154c > /sys/bus/pci/drivers/vfio-pci/new_id
qemu-system-x86_64 -accel kvm -m 4096 -cpu host \
-drive file=centos9.qcow2,if=none,id=virtio-disk0 \
-device virtio-blk-pci,drive=virtio-disk0,bootindex=0 -smp 4 \
-device vfio-pci,host=17:02.0 -net none \
-device vfio-pci,host=17:02.1 -net none \
-device vfio-pci,host=17:02.2 -net none \
-device vfio-pci,host=17:02.3 -net none \
-daemonize -vnc :5
Current result:
There is a probability that the mac of VF in guest is inconsistent with
it in host
Expected result:
When passthrough NIC VF to guest, the VF in guest should always get
the same mac as it in host.
Fixes: 14756b2ae2 ("iavf: Fix __IAVF_RESETTING state usage")
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Lengths of SG pointers are kept in the following order in
the SG entries in hardware.
63 48|47 32|31 16|15 0
-----------------------------------------
| Len 0 | Len 1 | Len 2 | Len 3 |
-----------------------------------------
| Ptr 0 |
-----------------------------------------
| Ptr 1 |
-----------------------------------------
| Ptr 2 |
-----------------------------------------
| Ptr 3 |
-----------------------------------------
Dma pointers have to be unmapped based on their
respective lengths given in this format.
Fixes: 37d79d0596 ("octeon_ep: add Tx/Rx processing and interrupt support")
Signed-off-by: Shinas Rasheed <srasheed@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
