The k3_udma_glue_tx_get_irq() function currently returns negative error
codes on error, zero on error and positive values for success. This
complicates life for the callers who need to propagate the error code.
Also GCC will not warn about unsigned comparisons when you check:
if (unsigned_irq <= 0)
All the callers have been fixed now but let's just make this easy going
forward.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "tx_chn->irq" variable is unsigned so the error checking does not
work correctly.
Fixes: 128d5874c0 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For AM65x SR2.0 it's required to enable IEP1 in raw 64bit mode which is
used by PRU FW to monitor the link and apply w/a for 10M link issue.
Note. No public errata available yet.
Without this w/a the PRU FW will stuck if link state changes under TX
traffic pressure.
Hence, add support for 10M full duplex for AM65x SR2.0:
- add new IEP API to enable IEP, but without PTP support
- add pdata quirk_10m_link_issue to enable 10M link issue w/a.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet timestamping TS and PTP PHC clock support.
For AM65x and AM64x:
- IEP1 is not used
- IEP0 is configured in shadow mode with 1ms cycle and shared between
Linux and FW. It provides time and TS in number cycles, so special
conversation in ns is required.
- IEP0 shared between PRUeth ports.
- IEP0 supports PPS, periodic output.
- IEP0 settime() and enabling PPS required FW interraction.
- RX TS provided with each packet in CPPI5 descriptor.
- TX TS returned through separate ICSSG hw queues for each port. TX TS
readiness is signaled by INTC IRQ. Only one packet at time can be requested
for TX TS.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Co-developed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver for Industrial Ethernet Peripheral (IEP) block of PRUSS to
support timestamping of ethernet packets and thus support PTP and PPS
for PRU ethernet ports.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add suspend / resume APIs to support power management in ICSSG ethernet
driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_ethtool.c file. This file will be used for dumping statistics
via ethtool for ICSSG ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement .ndo_get_stats64 to dump standard network interface
statistics for ICSSG ethernet driver.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_stats.c to help dump, icssg related driver statistics.
ICSSG has hardware registers for providing statistics like total rx bytes,
total tx bytes, etc. These registers are of 32 bits and hence in case of 1G
link, they overflows in around 32 seconds. The behaviour of these registers
is such that they don't roll back to 0 after overflow but rather stay at
UINT_MAX.
These registers support a feature where the value written to them is
subtracted from the register. This feature can be utilized to fix the
overflowing of stats.
This solution uses a Workqueues based solution where a function gets
called before the registers overflow (every 25 seconds in 1G link, 25000
seconds in 100M link), this function saves the register
values in local variables and writes the last read value to the
register. So any update during the read will be taken care of.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the Ethernet driver for TI AM654 Silicon rev. 2
with the ICSSG PRU Sub-system running dual-EMAC firmware.
The Programmable Real-time Unit and Industrial Communication Subsystem
Gigabit (PRU_ICSSG) is a low-latency microcontroller subsystem in the TI
SoCs. This subsystem is provided for the use cases like implementation of
custom peripheral interfaces, offloading of tasks from the other
processor cores of the SoC, etc.
Every ICSSG core has two Programmable Real-Time Unit(PRUs),
two auxiliary Real-Time Transfer Unit (RT_PRUs), and
two Transmit Real-Time Transfer Units (TX_PRUs). Each one of these runs
its own firmware. Every ICSSG core has two MII ports connect to these
PRUs and also a MDIO port.
The cores can run different firmwares to support different protocols and
features like switch-dev, timestamping, etc.
It uses System DMA to transfer and receive packets and
shared memory register emulation between the firmware and
driver for control and configuration.
This patch adds support for basic EMAC functionality with 1Gbps
and 100Mbps link speed. 10M and half duplex mode are not supported
currently as they require IEP, the support for which will be added later.
Support for switch-dev, timestamp, etc. will be added later
by subsequent patch series.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_queue.c file. This file introduces macros and APIs related to
ICSSG queues. These will be used by ICSSG Ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add icssg_config.h / .c and icssg_classifier.c files. These are firmware
configuration and classification related files. These will be used by
ICSSG ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MII helper APIs and MACROs. These APIs and MACROs will be later used
by ICSSG Ethernet driver. Also introduce icssg_prueth.h which has
definition of prueth related structures.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add firmware interface related headers and macros for ICSSG Ethernet
driver. These macros will be later used by the ICSSG ethernet driver.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
