In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.
At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.
The selftest itself however checks vetoing of a different aspect of the
configuration and the bridge does not need to participate in routing
traffic. The IP address or the RIF are irrelevant.
Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This tests creates as many RIFs as possible, ideally more than there can be
RIF counters (though that is currently only possible on Spectrum-1). It
then tries to enable L3 HW stats on each of the RIFs. It also contains the
traffic test, which tries to run traffic through a log2 of those counters
and checks that the traffic is shown in the counter values.
Like with tc_flower traffic test, take a log2 subset of rules. The logic
behind picking log2 rules is that then every bit of the instantiated item's
number is exercised. This should catch issues whether they happen at the
high end, low end, or somewhere in between.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scale tests are verifying behavior of mlxsw when number of instances of
some resource reaches the ASIC capacity. The number of instances is
referred to as "target" number.
No scale tests so far needed to know this target number to clean up. E.g.
the tc_flower simply removes the clsact qdisc that all the tested filters
are hooked onto, and that takes care of collecting all the filters.
However, for the RIF counter test, which is being added in a future patch,
VLAN netdevices are created. These are created as part of the test, but of
course the cleanup needs to undo them again. For that it needs to know how
many there were. To support this usage, pass the target number to the
cleanup callback.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scale tests are currently testing two things: that some number of
instances of a given resource can actually be created; and that when an
attempt is made to create more than the supported amount, the failures are
noted and handled gracefully.
Sometimes the scale test depends on more than one resource. In particular,
a following patch will add a RIF counter scale test, which depends on the
number of RIF counters that can be bound, and also on the number of RIFs
that can be created.
When the test is limited by the auxiliary resource and not by the primary
one, there's no point trying to run the overflow test, because it would be
testing exhaustion of the wrong resource.
To support this use case, when the $test_get_target yields 0, skip the test
instead.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scale tests are currently testing two things: that some number of
instances of a given resource can actually be created; and that when an
attempt is made to create more than the supported amount, the failures are
noted and handled gracefully.
However the ability to allocate the resource does not mean that the
resource actually works when passing traffic. For that, make it possible
for a given scale to also test traffic.
Traffic test is only run on the positive leg of the scale test (no point
trying to pass traffic when the expected outcome is that the resource will
not be allocated). Traffic tests are opt-in, if a given test does not
expose it, it is not run.
To this end, delay the test cleanup until after the traffic test is run.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scale of each resource is tested in the following manner:
1. The scale target is queried.
2. The test setup is prepared.
3. The test is invoked.
In some cases, the occupancy of a resource changes as part of the second
step, requiring the test to return a scale target that takes this change
into account.
Make this more robust by re-querying the scale target after the second
step.
Another possible solution is to swap the first and second steps, but
when a test needs to be skipped (i.e., scale target is zero), the setup
would have been in vain.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test runs several test cases and is supposed to return an error in
case at least one of them failed.
Currently, the check of the return value of each test case is in the
wrong place, which can result in the wrong return value. For example:
# TESTS='tc_police' ./resource_scale.sh
TEST: 'tc_police' [default] 968 [FAIL]
tc police offload count failed
Error: mlxsw_spectrum: Failed to allocate policer index.
We have an error talking to the kernel
Command failed /tmp/tmp.i7Oc5HwmXY:969
TEST: 'tc_police' [default] overflow 969 [ OK ]
...
TEST: 'tc_police' [ipv4_max] overflow 969 [ OK ]
$ echo $?
0
Fix this by moving the check to be done after each test case.
Fixes: 059b18e21c ("selftests: mlxsw: Return correct error code in resource scale test")
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The device stores flood records in a singly linked list where each
record stores up to X IP addresses of remote VTEPs.
The number of records is changed according to ASIC type and address
family.
Add a test which is similar to the existing IPv4 test to check IPv6.
The test is dedicated for Spectrum-1 switches, which support up to five
IPv6 addresses in one record.
The test verifies that packets are correctly flooded in various cases such
as deletion of a record in the middle of the list.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query the maximum number of supported RIF MAC profiles using
devlink-resource and verify that all available MAC profiles can be utilized
and that an error is generated when user space tries to exceed this number.
Output example in Spectrum-2:
$ TESTS='rif_mac_profile' ./resource_scale.sh
TEST: 'rif_mac_profile' 4 [ OK ]
TEST: 'rif_mac_profile' overflow 5 [ OK ]
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of mlxsw-specific selftests currently detect whether they are run
on a compatible machine, and bail out silently when not. These tests are
however done in a somewhat impenetrable manner by directly comparing PCI
IDs against a blacklist or a whitelist, and bailing out silently if the
machine is not compatible.
Instead, add a helper, mlxsw_only_on_spectrum(), which allows specifying
the supported machines in a human-readable manner. If the current machine
is incompatible, the helper emits a SKIP message and returns an error code,
based on which the caller can gracefully bail out in a suitable way. This
allows a more readable conditions such as:
mlxsw_only_on_spectrum 2+ || return
Convert all existing open-coded guards to the new helper. Also add two new
guards to do_mark_test() and do_drop_test(), which are supported only on
Spectrum-2+, but the corresponding check was not there.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the resource scale test checks a few cases, when the error code
resets between the cases. So for example, if one case fails and the
consecutive case passes, the error code eventually will fit the last test
and will be 0.
Save a new return code that will hold the 'or' return codes of all the
cases, so the final return code will consider all the cases.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query the maximum number of supported physical ports using devlink-resource
and test that this number can be reached by splitting each of the
splittable ports to its width. Test that an error is returned in case
the maximum number is exceeded.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add tests to ensure that the forbidden and unsupported cases are indeed
vetoed by mlxsw driver.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query the maximum number of supported policers using devlink-resource
and test that this number can be reached by configuring tc filters with
police action. Test that an error is returned in case the maximum number
is exceeded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the number of analyzers taken from the devlink command, instead of
hard-coded value, in order to make the test more generic.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't source lib.sh twice and make the script work with ifnames passed
on the command line.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't source lib.sh 2 times and make the script work with ifnames
passed on the command line.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a scale test capable of validating that offloaded network
functionality is indeed functional at scale when configured to
the different KVD profiles available.
Start by testing offloaded routes are functional at scale by
passing traffic on each one of them in turn.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a wrapper around mlxsw/mirror_gre_scale.sh that parameterized number
of offloadable mirrors on Spectrum machines.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a wrapper around mlxsw/tc_flower_scale.sh that parameterizes the
generic tc flower scale test template with Spectrum-specific target
values.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 routes in Spectrum are based on the kvd single-hash, but as it's
a hash we need to assume we cannot reach 100% of its capacity.
Add a wrapper that provides us with good/bad target numbers for the
Spectrum ASIC.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
[petrm@mellanox.com: Drop shebang.]
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a selftest that can be used to perform basic sanity of the devlink
resource API as well as test the behavior of KVD manipulation in the
driver.
This is the first case of a HW-only test - in order to test the devlink
resource a driver capable of exposing resources has to be provided
first.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
[petrm@mellanox.com: Extracted two patches out of this patch. Tweaked
commit message.]
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This library builds on top of devlink_lib.sh and contains functionality
specific to Spectrum ASICs, e.g., re-partitioning the various KVD
sub-parts.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
[petrm@mellanox.com: Split this out from another patch. Fix line length
in devlink_sp_read_kvd_defaults().]
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
