Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
Pull ARM SoC DT updates from Arnd Bergmann:
"This is a rather large update for the ARM devicetree files, after a
few quieter releases, with 775 total commits and 47 branches pulled
into this one.
There are 5 new SoC types plus some minor variations, and a total of
60 new machines, so I'm limiting the summary to the main noteworthy
items:
- Apple M1 gain support for PCI and pinctrl, getting a bit closer to
a usable system out of the box.
- Qualcomm gains support for Snapdragon 690 (aka SM6350) as well as
SM7225, 11 new smartphones, and three additional Chromebooks, and
improvements all over the place.
- Samsung gains support for ExynosAutov9, an automotive version of
their smartphone SoC, but otherwise no major changes.
- Microchip adds the SAMA5D29 SoC in the SAMA5 family, and a number
of improvements for the recently added SAMA7 family. The LAN966 SoC
that was added in the platform code does not have dts files yet.
Two board files are added for the older at91sam9g20 SoC
- Aspeed supports two additional server boards using their AST2600 as
BMC, and improves support for qemu models
- Rockchip RK3566/RK3688 gets added, along with six new development
boards using RK3328/RK3399/RK3566, and one Chromebook tablet.
- Two NAS boxes are added using the ARMv4 based Gemini platform
- One new board is added to the Intel Arria SoC FPGA family
- Marvell adds one network switch based on Armada 381 and the new
MOCHAbin 7040 development board
- NXP adds support for the S32G2 automotive SoC, two imx6 based ebook
readers, and three additional development boards, which is notably
less than their usual additions, but they also gain improvements to
their many existing boards
- STmicroelectronics adds their stm32mp13 SoC family along with a
reference board
- Renesas adds new versions of their R-Car Gen3 SoCs and many updates
for their older generations
- Broadcom adds support for a number of Cisco Meraki wireless
controllers, along with two new boards and other updates for
BCM53xx/BCM47xx networking SoCs and the Raspberry Pi boards
- Mediatek improves support for the MT81xx SoCs used in Chromebooks
as well as the MT76xx networking SoCs
- NVIDIA adds a number of cleanups and additional support for more
hardware on the already supported machines
- TI K3 adds support for three new boards along with cleanups
- Toshiba adds one board for the Visconti family
- Xilinx adds five new ZynqMP based machines
- Amlogic support is added for the Radxa Zero and two Jethub home
automation controllers, along with changes to other machines
- Rob Herring continues his work on fixing dtc warnings all over the
tree.
- Minor updates for TI OMAP, Mstar, Allwinner/sunxi, Hisilicon,
Ux500, Unisoc"
* tag 'dt-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (720 commits)
arm64: dts: apple: j274: Expose PCI node for the Ethernet MAC address
arm64: dts: apple: t8103: Add root port interrupt routing
arm64: dts: apple: t8103: Add PCIe DARTs
arm64: apple: Add PCIe node
arm64: apple: Add pinctrl nodes
ARM: dts: arm: Update ICST clock nodes 'reg' and node names
ARM: dts: arm: Update register-bit-led nodes 'reg' and node names
arm64: dts: exynos: add chipid node for exynosautov9 SoC
ARM: dts: qcom: fix typo in IPQ8064 thermal-sensor node
Revert "arm64: dts: qcom: msm8916-asus-z00l: Add sensors"
arm64: dts: qcom: ipq6018: Remove unused 'iface_clk' property from dma-controller node
arm64: dts: qcom: ipq6018: Remove unused 'qcom,config-pipe-trust-reg' property
arm64: dts: qcom: sm8350: Add CPU topology and idle-states
arm64: dts: qcom: Drop unneeded extra device-specific includes
arm64: dts: qcom: msm8916: Drop standalone smem node
arm64: dts: qcom: Fix node name of rpm-msg-ram device nodes
arm64: dts: qcom: msm8916-asus-z00l: Add sensors
arm64: dts: qcom: msm8916-asus-z00l: Add SDCard
arm64: dts: qcom: msm8916-asus-z00l: Add touchscreen
arm64: dts: qcom: sdm845-oneplus: remove devinfo-size from ramoops node
...
As defined by Documentation/devicetree/bindings/pci/pci-ep.yaml,
PCIe endpoints match this pattern:
properties:
$nodename:
pattern: "^pcie-ep@"
Change the existing ones in the DT bindings examples to avoid warnings
during DT bindings validation.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
- Add max-virtual-functions to endpoint binding (Kishon Vijay Abraham I)
- Add pci_epf_add_vepf() API to add virtual function to endpoint (Kishon
Vijay Abraham I)
- Add pci_epf_vepf_link() to link virtual function to endpoint physical
function (Kishon Vijay Abraham I)
- Add virtual function number to pci_epc_ops endpoint ops interfaces
(Kishon Vijay Abraham I)
- Simplify register base address computation for endpoint BAR configuration
(Kishon Vijay Abraham I)
- Add support to configure virtual functions in cadence endpoint driver
(Kishon Vijay Abraham I)
- Add SR-IOV configuration to endpoint test driver (Kishon Vijay Abraham I)
- Document configfs usage to create virtual functions for endpoints (Kishon
Vijay Abraham I)
* remotes/lorenzo/pci/endpoint:
Documentation: PCI: endpoint/pci-endpoint-cfs: Guide to use SR-IOV
misc: pci_endpoint_test: Populate sriov_configure ops to configure SR-IOV device
PCI: cadence: Add support to configure virtual functions
PCI: cadence: Simplify code to get register base address for configuring BAR
PCI: endpoint: Add virtual function number in pci_epc ops
PCI: endpoint: Add support to link a physical function to a virtual function
PCI: endpoint: Add support to add virtual function in endpoint core
dt-bindings: PCI: pci-ep: Add binding to specify virtual function
- Split DT bindings for PCIe controllers with independent MSI domains into
separate nodes for MT2712/MT7622 (Chuanjia Liu)
- Locate shared registers from "mediatek,generic-pciecfg" property
(Chuanjia Liu)
- Get IRQ from "pcie_irq" if "interrupt-names" property is present to fix
an MSI issue (Chuanjia Liu)
- Get PCI domain from "linux,pci-domain" property if present (Chuanjia Liu)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Use PCI domain to handle ports detection
PCI: mediatek: Add new method to get irq number
PCI: mediatek: Add new method to get shared pcie-cfg base address
dt-bindings: PCI: mediatek: Update the Device tree bindings
There are two independent PCIe controllers in MT2712 and MT7622
platform. Each of them should contain an independent MSI domain.
In old dts architecture, MSI domain will be inherited from the root
bridge, and all of the devices will share the same MSI domain.
Hence that, the PCIe devices will not work properly if the irq number
which required is more than 32.
Split the PCIe node for MT2712 and MT7622 platform to comply with
the hardware design and fix MSI issue.
Link: https://lore.kernel.org/r/20210823032800.1660-2-chuanjia.liu@mediatek.com
Signed-off-by: Chuanjia Liu <chuanjia.liu@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh+dt@kernel.org>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
Pull ARM SoC updates from Olof Johansson:
"A few SoC (code) changes have queued up this cycle, mostly for minor
changes and some refactoring and cleanup of legacy platforms. This
branch also contains a few of the fixes that weren't sent in by the
end of the release (all fairly minor).
- Adding an additional maintainer for the TEE subsystem (Sumit Garg)
- Quite a significant modernization of the IXP4xx platforms by Linus
Walleij, revisiting with a new PCI host driver/binding, removing
legacy mach/* include dependencies and moving platform
detection/config to drivers/soc. Also some updates/cleanup of
platform data.
- Core power domain support for Tegra platforms, and some
improvements in build test coverage by adding stubs for compile
test targets.
- A handful of updates to i.MX platforms, adding legacy (non-PSCI)
SMP support on i.MX7D, SoC ID setup for i.MX50, removal of platform
data and board fixups for iMX6/7.
... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
Rockchip"
* tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (53 commits)
MAINTAINERS: Add myself as TEE subsystem reviewer
ixp4xx: fix spelling mistake in Kconfig "Devce" -> "Device"
hw_random: ixp4xx: Add OF support
hw_random: ixp4xx: Add DT bindings
hw_random: ixp4xx: Turn into a module
hw_random: ixp4xx: Use SPDX license tag
hw_random: ixp4xx: enable compile-testing
pata: ixp4xx: split platform data to its own header
soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h
PCI: ixp4xx: Add a new driver for IXP4xx
PCI: ixp4xx: Add device tree bindings for IXP4xx
ARM/ixp4xx: Make NEED_MACH_IO_H optional
ARM/ixp4xx: Move the virtual IObases
MAINTAINERS: ARM/MStar/Sigmastar SoCs: Add a link to the MStar tree
ARM: debug: add UART early console support for MSTAR SoCs
ARM: dts: ux500: Fix LED probing
ARM: imx: add smp support for imx7d
ARM: imx6q: drop of_platform_default_populate() from init_machine
arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
soc/tegra: fuse: Fix Tegra234-only builds
...
Pull char / misc driver updates from Greg KH:
"Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanalabs driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems
mushed together" tree...
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
mcb: Use DEFINE_RES_MEM() helper macro and fix the end address
PNP: moved EXPORT_SYMBOL so that it immediately followed its function/variable
bus: mhi: pci-generic: Add missing 'pci_disable_pcie_error_reporting()' calls
bus: mhi: Wait for M2 state during system resume
bus: mhi: core: Fix power down latency
intel_th: Wait until port is in reset before programming it
intel_th: msu: Make contiguous buffers uncached
intel_th: Remove an unused exit point from intel_th_remove()
stm class: Spelling fix
nitro_enclaves: Set Bus Master for the NE PCI device
misc: ibmasm: Modify matricies to matrices
misc: vmw_vmci: return the correct errno code
siox: Simplify error handling via dev_err_probe()
fpga: machxo2-spi: Address warning about unused variable
lkdtm/heap: Add init_on_alloc tests
selftests/lkdtm: Enable various testable CONFIGs
lkdtm: Add CONFIG hints in errors where possible
lkdtm: Enable DOUBLE_FAULT on all architectures
lkdtm/heap: Add vmalloc linear overflow test
lkdtm/bugs: XFAIL UNALIGNED_LOAD_STORE_WRITE
...
- Configure FC and FTS for functions other than 0 (Ryder Lee)
- Add missing MODULE_DEVICE_TABLE (Qiheng Lin)
- Add YAML schema for MediaTek (Jianjun Wang)
- Export pci_pio_to_address() for module use (Jianjun Wang)
- Add MediaTek MT8192 PCIe controller driver (Jianjun Wang)
- Add MediaTek MT8192 INTx support (Jianjun Wang)
- Add MediaTek MT8192 MSI support (Jianjun Wang)
- Add MediaTek MT8192 system power management support (Jianjun Wang)
* remotes/lorenzo/pci/mediatek:
MAINTAINERS: Add Jianjun Wang as MediaTek PCI co-maintainer
PCI: mediatek-gen3: Add system PM support
PCI: mediatek-gen3: Add MSI support
PCI: mediatek-gen3: Add INTx support
PCI: mediatek-gen3: Add MediaTek Gen3 driver for MT8192
PCI: Export pci_pio_to_address() for module use
dt-bindings: PCI: mediatek-gen3: Add YAML schema
PCI: mediatek: Add missing MODULE_DEVICE_TABLE
PCI: mediatek: Configure FC and FTS for functions other than 0
scripts/checkpatch.pl -f drivers/pci/controller/pcie-rcar-host.c:
WARNING: DT compatible string "renesas,pcie-r8a7779" appears un-documented -- check ./Documentation/devicetree/bindings/
#853: FILE: drivers/pci/controller/pcie-rcar-host.c:853:
+ { .compatible = "renesas,pcie-r8a7779",
Re-add the compatible value for R-Car H1, which was lost during the
json-schema conversion. Make the "resets" property optional on R-Car
H1, as it is not present yet on R-Car Gen1 SoCs.
Fixes: 0d69ce3c2c ("dt-bindings: PCI: rcar-pci-host: Convert bindings to json-schema")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/fb0bb969cd0e5872ab5eac70e070242c0d8a5b81.1619700202.git.geert+renesas@glider.be
Signed-off-by: Rob Herring <robh@kernel.org>
