This patch series adds support for Cadence's XSPI controller.
It supports 3 work modes.
1. ACMD (auto command) work mode
ACMD name is because it uses auto command engine in the controller.
It further has 2 modes PIO and CDMA (command DMA).
The CDMA work mode is dedicated for high-performance application
where very low software overhead is required. In this mode the
Command Engine is programmed by the series of linked descriptors
stored in system memory. These descriptors provide commands to execute
and store status information for finished commands.
The PIO mode work mode is dedicated for single operation where
constructing a linked list of descriptors would require too
much effort.
2. STIG (Software Triggered Instruction Generator) work mode
In STIG mode, controller sends low-level instructions to memory.
Each instruction is 128-bit width. There is special instruction
DataSequence which carries information about data phase.
Driver uses Slave DMA interface to transfer data as only this
interface can be used in STIG work mode.
3. Direct work mode
This work mode allows sending data without invoking any command through
the slave interface.
Currently only STIG work mode is enabled, remaining work modes will
be added later.
Changes since v5:
1. Added adjust_op_size to adjust op size according to sdma size.
Changes since v4:
1. Changed reg region names and lengths as suggested by Rob.
Changes since v3:
1. Removed ACMD PIO mode.
2. Return IRQ_HANDLED only for handled interrupts.
3. DT binding changes.
Changes since v2:
1. Removed extra lock around exec_op.
2. Removed PHY parameters setting from the driver, those will be
handled by bootstrap pins available in the controller.
Changes since v1:
1. Use ACMD PIO work mode for NOR read, program and erase operations,
for everything else use STIG(Software Triggered Instruction
Generator) work mode.
2. Changes suggested by Lukas.
Parshuram Thombare (2):
spi: cadence: add dt-bindings documentation for Cadence XSPI
controller
spi: cadence: add support for Cadence XSPI controller
.../devicetree/bindings/spi/cdns,xspi.yaml | 77 +++
drivers/spi/Kconfig | 12 +
drivers/spi/Makefile | 1 +
drivers/spi/spi-cadence-xspi.c | 640 +++++++++++++++++++++
4 files changed, 730 insertions(+)
create mode 100644 Documentation/devicetree/bindings/spi/cdns,xspi.yaml
create mode 100644 drivers/spi/spi-cadence-xspi.c
--
2.7.4
Pull devicetree updates from Rob Herring:
- Refine reserved memory nomap handling
- Merge some PCI and non-PCI address handling implementations
- Simplify of_address.h header ifdefs
- Improve printk handling of some 64-bit types
- Convert adi,adv7511, Arm ccree, Arm SCMI, Arm SCU, Arm TWD timer, Arm
VIC, arm,sbsa-gwdt, Arm/Amlogic SCPI, Aspeed I2C, Broadcom iProc PWM,
linaro,optee-tz, MDIO GPIO, Mediatek RNG, MTD physmap, NXP
pcf8563/pcf85263/pcf85363, Renesas TPU, renesas,emev2-smu,
renesas,r9a06g032-sysctrl, sysc-rmobile, Tegra20 EMC, TI AM56 PCI, TI
OMAP mailbox, TI SCI bindings, virtio-mmio, Zynq FPGA, and ZynqMP RTC
to DT schema
- Convert mux and mux controller bindings to schema. This includes MDIO
IIO, and I2C muxes.
- Add Arm PL031 RTC binding schema
- Add vendor prefixes for StarFive Technology Co. Ltd. and Insignal Ltd
- Fix some stale doc references
- Remove stale property-units.txt. Superseded by schema in dt-schema
repo.
- Fixes for 'unevaluatedProperties' handling (enabled with experimental
json-schema support)
- Drop redundant usage of minItems and maxItems across the tree
- Update some examples to use bindings with a schema
* tag 'devicetree-for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (83 commits)
dt-bindings: Fix 'unevaluatedProperties' errors in DT graph users
dt-bindings: display: renesas,du: Fix 'ports' reference
dt-bindings: media: adv7180: Add missing video-interfaces.yaml reference
dt-bindings: crypto: ccree: Convert to json-schema
dt-bindings: fpga: zynq: convert bindings to YAML
dt-bindings: rtc: zynqmp: convert bindings to YAML
dt-bindings: interrupt-controller: Convert ARM VIC to json-schema
of: of_reserved_mem: mark nomap memory instead of removing
of: of_reserved_mem: only call memblock_free for normal reserved memory
dt-bindings: Drop redundant minItems/maxItems
dt-bindings: spmi: Correct 'reg' schema
of: reserved-memory: Add stub for RESERVEDMEM_OF_DECLARE()
dt-bindings: clk: vc5: Fix example
dt-bindings: timer: renesas,tmu: add r8a779a0 TMU support
dt-bindings: drm: bridge: adi,adv7511.txt: convert to yaml
dt-bindings: PCI: ti,am65: Convert PCIe host/endpoint mode dt-bindings to YAML
of: Remove superfluous casts when printing u64 values
of: Fix truncation of memory sizes on 32-bit platforms
dt-bindings: rtc: nxp,pcf8563: Absorb pcf85263/pcf85363 bindings
dt-bindings: pwm: Use examples with documented/matching schema
...
Originally, the Renesas RZ/N1 SPI Controller DT bindings were not
integrated in the main DT bindings for the Synopsys DesignWare
Synchronous Serial Interface, but in its own file, as the RZ/N1
controller has additional registers for software CS control and DMA.
As so far DMA is not supported on RZ/N1, and json-schema can handle any
possible differences fine, integrate the RZ/N1 compatible values in the
main DT bindings for the Synopsys DW SSI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/aef15aa119ed02487ded4691141678bc1040c3b4.1620301936.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull devicetree updates from Rob Herring:
- Refactor powerpc and arm64 kexec DT handling to common code. This
enables IMA on arm64.
- Add kbuild support for applying DT overlays at build time. The first
user are the DT unittests.
- Fix kerneldoc formatting and W=1 warnings in drivers/of/
- Fix handling 64-bit flag on PCI resources
- Bump dtschema version required to v2021.2.1
- Enable undocumented compatible checks for dtbs_check. This allows
tracking of missing binding schemas.
- DT docs improvements. Regroup the DT docs and add the example schema
and DT kernel ABI docs to the doc build.
- Convert Broadcom Bluetooth and video-mux bindings to schema
- Add QCom sm8250 Venus video codec binding schema
- Add vendor prefixes for AESOP, YIC System Co., Ltd, and Siliconfile
Technologies Inc.
- Cleanup of DT schema type references on common properties and
standard unit properties
* tag 'devicetree-for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (64 commits)
powerpc: If kexec_build_elf_info() fails return immediately from elf64_load()
powerpc: Free fdt on error in elf64_load()
of: overlay: Fix kerneldoc warning in of_overlay_remove()
of: linux/of.h: fix kernel-doc warnings
of/pci: Add IORESOURCE_MEM_64 to resource flags for 64-bit memory addresses
dt-bindings: bcm4329-fmac: add optional brcm,ccode-map
docs: dt: update writing-schema.rst references
dt-bindings: media: venus: Add sm8250 dt schema
of: base: Fix spelling issue with function param 'prop'
docs: dt: Add DT API documentation
of: Add missing 'Return' section in kerneldoc comments
of: Fix kerneldoc output formatting
docs: dt: Group DT docs into relevant sub-sections
docs: dt: Make 'Devicetree' wording more consistent
docs: dt: writing-schema: Include the example schema in the doc build
docs: dt: writing-schema: Remove spurious indentation
dt-bindings: Fix reference in submitting-patches.rst to the DT ABI doc
dt-bindings: ddr: Add optional manufacturer and revision ID to LPDDR3
dt-bindings: media: video-interfaces: Drop the example
devicetree: bindings: clock: Minor typo fix in the file armada3700-tbg-clock.txt
...
This helps validating DTS files.
Changes that require mentioning:
1. reg-names
"mspi_regs" and "bspi_regs" were renamed to "mspi" and "bspi" as that
is what's used in DTS files and in Linux driver
2. interrupt-names
Names were reordered. "mspi_done" has to go first as it's always
required.
3. spi-rx-bus-width
Property description was dropped as it's part of the
spi-controller.yaml
4. Examples:
* drop partitions as they are well documented elsewhere
* regs and interrupts were formatted and reordered to match yaml
* <0x1c> was replaced with <&gic>
* "m25p80" node name became "flash"
* dropped invalid "m25p,fast-read" property
* dropped undocumented and Linux-unused "clock-names"
This rewritten binding validates cleanly using the "dt_binding_check".
Some Linux stored DTS files will require reordering regs and interrupts
to make dtbs_check happy.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210416194723.23855-1-zajec5@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no way as of now to have a parent or bus defining properties
for child nodes. For now, avoid it in the example to silence warnings on
dt_schema_check. We can figure out how to deal with actual dts files
later.
[p.yadav@ti.com: Fix how compatible is defined, make reset optional, fix
minor typos, remove subnode properties in example, update commit
message.]
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210326130034.15231-5-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull devicetree updates from Rob Herring:
- Sync dtc to upstream version v1.6.0-51-g183df9e9c2b9 and build host
fdtoverlay
- Add kbuild support to build DT overlays (%.dtbo)
- Drop NULLifying match table in of_match_device().
In preparation for this, there are several driver cleanups to use
(of_)?device_get_match_data().
- Drop pointless wrappers from DT struct device API
- Convert USB binding schemas to use graph schema and remove old plain
text graph binding doc
- Convert spi-nor and v3d GPU bindings to DT schema
- Tree wide schema fixes for if/then schemas, array size constraints,
and undocumented compatible strings in examples
- Handle 'no-map' correctly for already reserved memblock regions
* tag 'devicetree-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
driver core: platform: Drop of_device_node_put() wrapper
of: Remove of_dev_{get,put}()
dt-bindings: usb: Change descibe to describe in usbmisc-imx.txt
dt-bindings: can: rcar_canfd: Group tuples in pin control properties
dt-bindings: power: renesas,apmu: Group tuples in cpus properties
dt-bindings: mtd: spi-nor: Convert to DT schema format
dt-bindings: Use portable sort for version cmp
dt-bindings: ethernet-controller: fix fixed-link specification
dt-bindings: irqchip: Add node name to PRUSS INTC
dt-bindings: interconnect: Fix the expected number of cells
dt-bindings: Fix errors in 'if' schemas
dt-bindings: iommu: renesas,ipmmu-vmsa: Make 'power-domains' conditionally required
dt-bindings: Fix undocumented compatible strings in examples
kbuild: Add support to build overlays (%.dtbo)
scripts: dtc: Remove the unused fdtdump.c file
scripts: dtc: Build fdtoverlay tool
scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9
scripts: dtc: Fetch fdtoverlay.c from external DTC project
dt-bindings: thermal: sun8i: Fix misplaced schema keyword in compatible strings
dt-bindings: iio: dac: Fix AD5686 references
...
Pull spi updates from Mark Brown:
"The main focus of this release from a framework point of view has been
spi-mem where we've acquired support for a few new hardware features
which enable better performance on suitable hardware.
Otherwise mostly thanks to Arnd's cleanup efforts on old platforms
we've removed several obsolete drivers which just about balance out
the newer drivers we've added this cycle.
Summary:
- Allow drivers to flag if they are unidirectional.
- Support for DTR mode and hardware acceleration of dummy cycles in
spi-mem.
- Support for Allwinder H616, Intel Lightning Mountain, nVidia Tegra
QuadSPI, Realtek RTL838x and RTL839x.
- Removal of obsolete EFM32, Txx9 and SIRF Prima and Atlas drivers"
* tag 'spi-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (76 commits)
spi: Skip zero-length transfers in spi_transfer_one_message()
spi: dw: Avoid stack content exposure
spi: cadence-quadspi: Use spi_mem_dtr_supports_op()
spi: spi-mem: add spi_mem_dtr_supports_op()
spi: atmel-quadspi: Disable the QSPI IP at suspend()
spi: pxa2xx: Add IDs for the controllers found on Intel Lynxpoint
spi: pxa2xx: Fix the controller numbering for Wildcat Point
spi: Change provied to provided in the file spi.h
spi: mediatek: add set_cs_timing support
spi: support CS timing for HW & SW mode
spi: add power control when set_cs_timing
spi: stm32: make spurious and overrun interrupts visible
spi: stm32h7: replace private SPI_1HZ_NS with NSEC_PER_SEC
spi: stm32: defer probe for reset
spi: stm32: driver uses reset controller only at init
spi: stm32h7: ensure message are smaller than max size
spi: stm32: use bitfield macros
spi: stm32: do not mandate cs_gpio
spi: stm32: properly handle 0 byte transfer
spi: clps711xx: remove redundant white-space
...
