Pull char / misc / iio driver updates from Greg KH:
"Here is the big char/misc/iio and other small driver subsystem pull
request for 6.16-rc1.
Overall, a lot of individual changes, but nothing major, just the
normal constant forward progress of new device support and cleanups to
existing subsystems. Highlights in here are:
- Large IIO driver updates and additions and device tree changes
- Android binder bugfixes and logfile fixes
- mhi driver updates
- comedi driver updates
- counter driver updates and additions
- coresight driver updates and additions
- echo driver removal as there are no in-kernel users of it
- nvmem driver updates
- spmi driver updates
- new amd-sbi driver "subsystem" and drivers added
- rust miscdriver binding documentation fix
- other small driver fixes and updates (uio, w1, acrn, hpet,
xillybus, cardreader drivers, fastrpc and others)
All of these have been in linux-next for quite a while with no
reported problems"
* tag 'char-misc-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (390 commits)
binder: fix yet another UAF in binder_devices
counter: microchip-tcb-capture: Add watch validation support
dt-bindings: iio: adc: Add ROHM BD79100G
iio: adc: add support for Nuvoton NCT7201
dt-bindings: iio: adc: add NCT7201 ADCs
iio: chemical: Add driver for SEN0322
dt-bindings: trivial-devices: Document SEN0322
iio: adc: ad7768-1: reorganize driver headers
iio: bmp280: zero-init buffer
iio: ssp_sensors: optimalize -> optimize
HID: sensor-hub: Fix typo and improve documentation
iio: admv1013: replace redundant ternary operator with just len
iio: chemical: mhz19b: Fix error code in probe()
iio: adc: at91-sama5d2: use IIO_DECLARE_BUFFER_WITH_TS
iio: accel: sca3300: use IIO_DECLARE_BUFFER_WITH_TS
iio: adc: ad7380: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: adc: ad4695: rename AD4695_MAX_VIN_CHANNELS
iio: adc: ad4695: use IIO_DECLARE_DMA_BUFFER_WITH_TS
iio: introduce IIO_DECLARE_BUFFER_WITH_TS macros
iio: make IIO_DMA_MINALIGN minimum of 8 bytes
...
Pull hwmon updates from Guenter Roeck:
"New drivers:
- KEBA fan controller
- KEBA battery monitoring controller
- MAX77705
Support added to existing drivers:
- MAXIMUS VI HERO and ROG MAXIMUS Z90 Formula support (asus-ec-sensors)
- SQ52206 support (ina238)
- lt3074 support (pmbus/lt3074)
- ADPM12160 support (pmbus/max34440)
- MPM82504 and for MPM3695 family support (pmbus/mpq8785)
- Add the Dell OptiPlex 7050 to the DMI whitelist (dell-smm)
- Zen5 Ryzen Desktop support (k10temp)
Various other minor fixes and improvements"
* tag 'hwmon-for-v6.16' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (48 commits)
doc: hwmon: acpi_power_meter: Add information about enabling the power capping feature.
hwmon: (isl28022) Fix current reading calculation
hwmon: (lm75) Fix I3C transfer buffer pointer for incoming data
hwmon: Add KEBA fan controller support
hwmon: pmbus: mpq8785: Add support for MPM3695 family
hwmon: pmbus: mpq8785: Add support for MPM82504
hwmon: pmbus: mpq8785: Implement VOUT feedback resistor divider ratio configuration
hwmon: pmbus: mpq8785: Prepare driver for multiple device support
dt-bindings: hwmon: Add bindings for mpq8785 driver
hwmon: (ina238) Modify the calculation formula to adapt to different chips
hwmon: (ina238) Add support for SQ52206
dt-bindings: Add SQ52206 to ina2xx devicetree bindings
hwmon: (ina238) Add ina238_config to save configurations for different chips
hwmon: (ausus-ec-sensors) add MAXIMUS VI HERO.
hwmon: (isl28022, nct7363) Convert to use maple tree register cache
hwmon: (asus-ec-sensors) check sensor index in read_string()
hwmon: (asus-ec-sensors) add ROG MAXIMUS Z90 Formula.
dt-bindings: hwmon: Add Sophgo SG2044 external hardware monitor support
hwmon: (max77705) Add initial support
hwmon: (tmp102) add vcc regulator support
...
The KEBA fan controller is found in the system FPGA of KEBA PLC devices.
It detects if the fan is removed or blocked. For fans with tacho signal
the monitoring of the speed of the fan is supported. It also supports to
regulate the speed of fans with PWM input.
The auxiliary device for this driver is instantiated by the cp500 misc
driver.
Signed-off-by: Gerhard Engleder <eg@keba.com>
Link: https://lore.kernel.org/r/20250425194823.54664-1-gerhard@engleder-embedded.com
[groeck: Added various missing "break;" statements]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The EC of OneXPlayer devices used to only control the fan. This is no
longer the case, with the EC of OneXPlayer gaining additional
functionality (turbo button, turbo led, battery controls).
As it will be beneficial from a complexity perspective to retain this
driver as a single unit, move it out of hwmon, and into platform/x86.
Also, remove the hwmon documentation to prepare moving it to
Documentation/ABI/.
While at it, add myself to the maintainer's file.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Derek J. Clark <derekjohn.clark@gmail.com>
Signed-off-by: Antheas Kapenekakis <lkml@antheas.dev>
Link: https://lore.kernel.org/r/20250425111821.88746-4-lkml@antheas.dev
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
The KEBA battery monitoring controller is found in the system FPGA of
KEBA PLC devices. It puts a load on the coin cell battery to check the
state of the battery. If the coin cell battery is nearly empty, then
the user space is signaled with a hwmon alarm.
The auxiliary device for this driver is instantiated by the cp500 misc
driver.
Signed-off-by: Gerhard Engleder <eg@keba.com>
Link: https://lore.kernel.org/r/20250409190830.60489-1-gerhard@engleder-embedded.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the Congatec Board Controller. This controller exposes
temperature, voltage, current and fan sensors.
The available sensors list cannot be predicted. Some sensors can be
present or not, depending the system.
The driver has an internal list of all possible sensors, for all Congatec
boards. The Board Controller gives to the driver its sensors list, and
their status (active or not).
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20250203-congatec-board-controller-hwmon-v4-1-ff6c76a4662c@bootlin.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon updates from Guenter Roeck:
"New drivers:
- PMBus client driver for Intel CRPS185 power supply
- PMBus client driver for Texas Instruments TPS25990
Chip support added to existing drivers:
- pmbus/max15301: Add support for MAX15303
- pmbus/adm1275: Add adm1273 support
- lm75: Add NXP P3T1755 support; with it, add I3C support to the
driver
- asus-ec-sensors: Add TUF GAMING X670E PLUS
Other notable changes:
- nct6683: Add customer IDs for several MSI and ASRock boards
- tmp108: Add regulator support
- Improve write protect support in PMBus core
- pmbus/dps920ab: Add ability to instantiate through i2c
- The hwmon core now accepts NULL as device name parameter to
[devm_]hwmon_device_register_with_info ans uses the parent device
name as fallback in that case
- The PMBus core now provides the PMBUs revision in a debugfs file
- asus-ec-sensors: Support for optional CPU fan on AMD 600
motherboards
- raspberrypi: Add PM suspend/resume support
- dell-smm: Enable manual fan control support on Dell XPS 9370
- pwm-fan: Default to maximum cooling level if provided
And various other minor fixes and improvements"
* tag 'hwmon-for-v6.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (44 commits)
hwmon: pmbus: dps920ab: Add ability to instantiate through i2c
hwmon: (pwm-fan) Default to the Maximum cooling level if provided
hwmon: (asus_atk0110) Use str_enabled_disabled() and str_enable_disable() helpers
hwmon: Fix help text for aspeed-g6-pwm-tach
hwmon: (dell-smm) Add Dell XPS 9370 to fan control whitelist
hwmon: (acpi_power_meter) Fix update the power trip points on failure
hwmon: (acpi_power_meter) Fix uninitialized variables
hwmon: (core) Use device name as a fallback in devm_hwmon_device_register_with_info
hwmon: (pmbus/max15301) Add support for MAX15303
hwmon: (pmbus/adm1275) add adm1273 support
dt-bindings: hwmon: adm1275: add adm1273
hwmon: (nct6683) Add another customer ID for MSI
hwmon: (pwm-fan): Make use of device properties everywhere
hwmon: (lm75) add I3C support for P3T1755
hwmon: (lm75) separate probe into common and I2C parts
hwmon: (lm75) Remove superfluous 'client' member from private struct
hwmon: (lm75) simplify regulator handling
hwmon: (lm75) simplify lm75_write_config()
hwmon: (lm75) Hide register size differences in regmap access functions
hwmon: (pmbus/crps) Add Intel CRPS185 power supply
...
Pull mfd updates from Lee Jones:
- Fix race in device_node_get_regmap() using more extensive locking
- Remove unused platform driver support for syscon
- Allow syscon nodes to be registered without a "syscon" compatible
string
- Make `platform_data` pointer const in struct mfd_cell
- Revert support for multiple AXP PMICs to avoid regressions
- Increase SoundWire attach timeout and use gpiod_set_raw() for GPIO
operation
- Store the result from fault_log() for use by other sub-components
- Fix an invalid regmap-config max_register value
- Add another Gemini Lake ISA bridge PCI device ID
- Use devm_register_power_off_handler() to simplify code
- Add support for QNAP microcontroller units, including LEDs, input,
and hwmon
- Use MFD_CELL macros and remove unused code
- Add support for AAEON UP board FPGA
- Remove unused includes
- Fix various typos and compatibility issues in multiple bindings
- Add new bindings for rk3562 QoS, LED1202, and qcom,tcsr-ipq5424
- Convert several bindings to YAML schema
- Update sprd,sc2731 bindings to reference sprd,sc2731-efuse bindings
directly
- Fix rohm,bd71815 bindings by correcting resistor values and typos
- Documentation improvements:
- Add documentation for LED1202 and qnap-mcu-hwmon
- Adjust the file entry for the qnap-mcu header in MAINTAINERS
* tag 'mfd-next-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (35 commits)
MAINTAINERS: Adjust the file entry for the qnap-mcu header
dt-bindings: mfd: syscon: Fix ti,j784s4-acspcie-proxy-ctrl compatible
dt-bindings: mfd: syscon: Fix al,alpine-sysfabric-service compatible
Revert "mfd: axp20x: Allow multiple regulators"
dt-bindings: mfd: syscon: Add rk3562 QoS register compatible
mfd: syscon: Allow syscon nodes without a "syscon" compatible
mfd: syscon: Remove the platform driver support
mfd: syscon: Fix race in device_node_get_regmap()
dt-bindings: mfd: atmel: Convert to YAML schema
dt-bindings: mfd: atmel,at91sam9260: Convert to YAML schema
dt-bindings: mfd: sprd,sc2731: Reference sprd,sc2731-efuse bindings
mfd: tps65219: Remove unused macros & add regmap.h
mfd: tps65219: Use MFD_CELL macros
leds: Add LED1202 I2C driver
dt-bindings: leds: Add LED1202 LED Controller
Documentation:leds: Add leds-st1202.rst
mfd: Add support for AAEON UP board FPGA
mfd: da9052: Store result from fault_log
mfd: intel_soc_pmic_chtdc_ti: Fix invalid regmap-config max_register value
mfd: cs42l43: Use devres for remove as well
...
Pull hmon updates from Guenter Roeck:
"New drivers:
- ISL28022 power monitor
- Nuvoton NCT7363Y
Added support for new chips to existing drivers:
- The tmp180 driver now supports NXP p3t1085, including its I3C mode
- The ina2xx driver now supports SY24655 and INA260
- The amc6821 driver now supports tsd,mule
Other notable improvements:
- The sht4x driver now supports the chip heater
- The pmbus/isl68137 driver now supports a voltage divider on Vout
- The cros_ec driver registers with the thermal framework
- The pmbus/ltc2978 driver now supports LTC7841
- The PMBus core now allow drivers to override WRITE_PROTECT
Various other minor improvements and cleanups"
* tag 'hwmon-for-v6.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (51 commits)
hwmon: (pmbus/isl68137) add support for voltage divider on Vout
dt-bindings: hwmon: isl68137: add bindings to support voltage dividers
hwmon: tmp108: fix I3C dependency
hwmon: (cros_ec) register thermal sensors to thermal framework
hwmon: (tmp108) Add support for I3C device
hwmon: (tmp108) Add helper function tmp108_common_probe() to prepare I3C support
hwmon: (acpi_power_meter) Fix fail to load module on platform without _PMD method
hwmon: (nct6775-core) Fix overflows seen when writing limit attributes
hwmon: (pwm-fan) Introduce start from stopped state handling
dt-bindings: hwmon: pwm-fan: Document start from stopped state properties
hwmon: (tmp108) Add NXP p3t1085 support
dt-bindings: hwmon: ti,tmp108: Add nxp,p3t1085 compatible string
hwmon: (sch5627, max31827) Fix typos in driver documentation
hwmon: (jc42) Drop of_match_ptr() protection
hwmon: (f71882fg) Fix grammar in fan speed trip points explanation
dt-bindings: hwmon: pmbus: add ti tps25990 support
hwmon: (pmbus/core) clear faults after setting smbalert mask
hwmon: (pmbus/core) allow drivers to override WRITE_PROTECT
hwmon: (pmbus) add documentation for existing flags
hwmon: (ina226) Add support for SY24655
...
It's possible to build a kernel with tmp108 built-in but i3c support
in a loadable module, but that results in a link failure:
x86_64-linux-ld: drivers/hwmon/tmp108.o: in function `p3t1085_i3c_probe':
tmp108.c:(.text+0x5f9): undefined reference to `i3cdev_to_dev'
Add a Kconfig dependency to ensure only the working configurations
are allowed.
Fixes: c40655e331 ("hwmon: (tmp108) Add support for I3C device")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Message-ID: <20241113175615.2442851-1-arnd@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add compatible string 'nxp,p3t1085' since p3t1085's register layout is the
same as tmp108.
The p3t1085 supports I3C interface.
Update document tmp108.rst and Kconfig's help context.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Message-ID: <20241111-p3t1085-v3-2-bff511550aad@nxp.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SY24655: Support for current and voltage detection as well as
power calculation.
Signed-off-by: Wenliang Yan <wenliang202407@163.com>
Message-ID: <20241106150547.2538-1-wenliang202407@163.com>
[groeck: Changed order of compatible entries;
dropped spurious extra return statement in is_visible();
fixed code problems]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The NCT7363Y is a fan controller which provides up to 16
independent FAN input monitors. It can report each FAN input count
values. The NCT7363Y also provides up to 16 independent PWM
outputs. Each PWM can output specific PWM signal by manual mode to
control the FAN duty outside.
Signed-off-by: Ban Feng <kcfeng0@nuvoton.com>
Message-ID: <20241022052905.4062682-3-kcfeng0@nuvoton.com>
[groeck: Dropped unnecessary variable initialization, and , after { }]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
INA260 is similar to other chips of the series, except it has an internal
shunt resistor. The calibration register is therefore not present. Also,
the current register address was changed, though that does not matter for
the driver since the shunt voltage register (which is now the current
register) value is already used to read the current.
Cc: Loic Guegan <loic.guegan@mailbox.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The embedded controller code is mainly used on x86 laptops and cannot
work without PC style I/O port access.
Make this a user-visible configuration option that is default enabled
on x86 but otherwise disabled, and that can never be enabled unless
CONFIG_HAS_IOPORT is also available.
The empty stubs in internal.h help ignore the EC code in configurations
that don't support it. In order to see those stubs, the sbshc code also
has to include this header and drop duplicate declarations.
All the direct callers of ec_read/ec_write already had an x86
dependency and now also need to depend on APCI_EC.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patch.msgid.link/20241011061948.3211423-1-arnd@kernel.org
[ rjw: Subject edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Update datasheet references. Replace misleading 'force parameter needed'
with 'must be instantiated explicitly'. Explain the reason for the missing
auto-detection. Mention all supported chips in Kconfig.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use regmap for local caching and for multi-byte operations to be able
to use regmap API functions and to reduce the need for locking in the
driver.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use regmap to replace local caching and to be able to use regmap API
functions.
No functional change.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull hwmon updates from Guenter Roeck:
"Obsolete driver removals:
- Removed obsolete adm1021 and max6642 drivers
New drivers:
- MPS MP2891, MP2993, MP9941, and MP5920
- SPD5118 (Temperature Sensor and EEPROM)
Added device support to existing drivers:
- g762: G761
- dell-smm: Dell OptiPlex 7060
- asus-ec-sensors: ProArt X670E-CREATOR WIFI
- corsair-psu: HX1200i Series 2023 psu
- nzxt-smart2: Additional USB IS for NZXT RGB & Fan Controller
Notable enhancements and fixes:
- Removed use of i2c_match_id()
- Constified struct regmap_config where feasible
- Cleaned up amc6821 driver, and converted to use regmap and
with_info API
- Converted max6639 driver to use with_info API; added support for
additional sysfs attributes
- Fixed various sysfs attribute underflows
- Added PEC support to hwmon core, and use in lm90 and max31827
drivers
And various other minor fixes and improvements"
* tag 'hwmon-for-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (103 commits)
hwmon: (max6697) Fix swapped temp{1,8} critical alarms
hwmon: (max6697) Fix underflow when writing limit attributes
hwmon: Remove obsolete adm1021 and max6642 drivers
hwmon: (pmbus/ltc4286) Drop unused i2c device ids
hwmon: (g762) Initialize fans after configuring clock
hwmon: (amc6821) Add support for pwm1_mode attribute
hwmon: (amc6821) Convert to with_info API
hwmon: (amc6821) Convert to use regmap
hwmon: (amc6821) Drop unnecessary enum chips
hwmon: (amc6821) Use BIT() and GENMASK()
hwmon: (amc6821) Use tabs for column alignment in defines
hwmon: (amc6821) Reorder include files, drop unnecessary ones
hwmon: (amc6821) Add support for fan1_target and pwm1_enable mode 4
hwmon: (amc6821) Rename fan1_div to fan1_pulses
hwmon: (amc6821) Make reading and writing fan speed limits consistent
hwmon: (amc6821) Stop accepting invalid pwm values
hwmon: (w83627ehf) Fix underflows seen when writing limit attributes
hwmon: (nct6775-core) Fix underflows seen when writing limit attributes
hwmon: (lm95234) Fix underflows seen when writing limit attributes
hwmon: (adc128d818) Fix underflows seen when writing limit attributes
...
ADM1021, MAX6642, and compatible chips are supported by the lm90 driver.
Remove the obsolete stand-alone drivers to reduce maintenance overhead.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use regmap for register accesses and caching.
While at it, use sysfs_emit() instead of sprintf() to write sysfs
attribute data, and remove spurious debug messages which would only
be seen as result of a bug in the code. Also make sure that error
codes are propagated and not replaced with -EIO.
While at it, introduce rounding of written temperature values and for
internal calculations to reduce deviation from written values and as
much as possible.
No functional change intended except for differences introduced by
rounding.
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
With SPD5118 chip detection for the most part handled by the i2c-smbus
core using DMI information, the spd5118 driver no longer needs to
auto-detect spd5118 compliant chips.
Auto-detection by the driver is still needed on systems with no DMI support
or on systems with more than eight DIMMs and can not be removed entirely.
However, it affects boot time and introduces the risk of mis-identifying
chips. Add configuration option to be able to disable it on systems where
chip detection is handled outside the driver.
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Thomas Weißschuh <linux@weissschuh.net>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This addition adds in the ability for the system to scan
the EC chip in the Lenovo ThinkStation systems to get the
current fan RPM speeds the Maximum speed value for each
fan also provides the CPU, DIMM other thermal statuses
Signed-off-by: David Ober <dober6023@gmail.com>
Link: https://lore.kernel.org/r/20240328121250.331146-1-dober6023@gmail.com
[groeck: Dropped pointless case statements]
[Colin King: Fixed spelling error accesssible -> accessible]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver support two functions: PWM and Tachometer. The PWM feature can
handle up to 16 output ports, while the Tachometer can monitor to up to 16
input ports as well. This driver implements them by exposing two kernel
subsystems: PWM and HWMON. The PWM subsystem can be utilized alongside
existing drivers for controlling elements such as fans (pwm-fan.c),
beepers (pwm-beeper.c) and so on. Through the HWMON subsystem, the driver
provides sysfs interfaces for fan.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Link: https://lore.kernel.org/r/20240221104025.1306227-4-billy_tsai@aspeedtech.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
