The port@0 node doesn't define any extra properties in the port or endpoint
nodes, so the $ref should be to "/properties/port" instead as it restricts
extra properties.
Fixes: 0f82ffa9a2 ("media: dt-bindings: media: i2c: Add bindings for TW9900")
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The data lanes and link frequency were set to match existing Linux driver
limitations, however bindings should be independent of chosen Linux
driver support.
Decouple these properties from the driver to match what is actually
supported by the hardware.
This also fixes DTS example:
ov8856.example.dtb: camera@10: port:endpoint:link-frequencies:0: [360000000] is too short
Fixes: 066a94e28a ("media: dt-bindings: media: Use graph and video-interfaces schemas")
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Document AK7345 bindings. Compared to AK7375, it has only 9 bits position
values (instead of 12), 20 ms power-up delay (instead of 10), and no known
standby register setting.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
[Sakari Ailus: Rewrap commit message.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The Techwell TW9900 is a video decoder supporting multiple input
standards such as PAL and NTSC and has a parallel BT.656 output
interface.
It's designed to be low-power, posesses some features such as a
programmable comb-filter, and automatic input standard detection
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mehdi Djait <mehdi.djait@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Pull media updates from Mauro Carvalho Chehab:
- the old V4L2 core videobuf kAPI was finally removed. All media
drivers should now be using VB2 kAPI
- new automotive driver: mgb4
- new platform video driver: npcm-video
- new sensor driver: mt9m114
- new TI driver used in conjunction with Cadence CSI2RX IP to bridge
TI-specific parts
- ir-rx51 was removed and the N900 DT binding was moved to the
pwm-ir-tx generic driver
- drop atomisp-specific ov5693, using the upstream driver instead
- the camss driver has gained RDI3 support for VFE 17x
- the atomisp driver now detects ISP2400 or ISP2401 at run time. No
need to set it up at build time anymore
- lots of driver fixes, cleanups and improvements
* tag 'media/v6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (377 commits)
media: nuvoton: VIDEO_NPCM_VCD_ECE should depend on ARCH_NPCM
media: venus: Fix firmware path for resources
media: venus: hfi_cmds: Replace one-element array with flex-array member and use __counted_by
media: venus: hfi_parser: Add check to keep the number of codecs within range
media: venus: hfi: add checks to handle capabilities from firmware
media: venus: hfi: fix the check to handle session buffer requirement
media: venus: hfi: add checks to perform sanity on queue pointers
media: platform: cadence: select MIPI_DPHY dependency
media: MAINTAINERS: Fix path for J721E CSI2RX bindings
media: cec: meson: always include meson sub-directory in Makefile
media: videobuf2: Fix IS_ERR checking in vb2_dc_put_userptr()
media: platform: mtk-mdp3: fix uninitialized variable in mdp_path_config()
media: mediatek: vcodec: using encoder device to alloc/free encoder memory
media: imx-jpeg: notify source chagne event when the first picture parsed
media: cx231xx: Use EP5_BUF_SIZE macro
media: siano: Drop unnecessary error check for debugfs_create_dir/file()
media: mediatek: vcodec: Handle invalid encoder vsi
media: aspeed: Drop unnecessary error check for debugfs_create_file()
Documentation: media: buffer.rst: fix V4L2_BUF_FLAG_PREPARED
Documentation: media: gen-errors.rst: fix confusing ENOTTY description
...
Pull devicetree updates from Rob Herring:
- Add a kselftest to check for unprobed DT devices
- Fix address translation for some 3 address cells cases
- Refactor firmware node refcounting for AMBA bus
- Add bindings for qcom,sm4450-pdc, Qualcomm Kryo 465 CPU, and
Freescale QMC HDLC
- Add Marantec vendor prefix
- Convert qcom,pm8921-keypad, cnxt,cx92755-wdt, da9062-wdt, and
atmel,at91rm9200-wdt bindings to DT schema
- Several additionalProperties/unevaluatedProperties on child node
schemas fixes
- Drop reserved-memory bindings which now live in dtschema project
- Fix a reference to rockchip,inno-usb2phy.yaml
- Remove backlight nodes from display panel examples
- Expand example for using DT_SCHEMA_FILES
- Merge simple LVDS panel bindings to one binding doc
* tag 'devicetree-for-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (34 commits)
dt-bindings: soc: fsl: cpm_qe: cpm1-scc-qmc: Add support for QMC HDLC
dt-bindings: soc: fsl: cpm_qe: cpm1-scc-qmc: Add 'additionalProperties: false' in child nodes
dt-bindings: soc: fsl: cpm_qe: cpm1-scc-qmc: Fix example property name
dt-bindings: arm,coresight-cti: Add missing additionalProperties on child nodes
dt-bindings: arm,coresight-cti: Drop type for 'cpu' property
dt-bindings: soundwire: Add reference to soundwire-controller.yaml schema
dt-bindings: input: syna,rmi4: Make "additionalProperties: true" explicit
media: dt-bindings: ti,ds90ub960: Add missing type for "i2c-alias"
dt-bindings: input: qcom,pm8921-keypad: convert to YAML format
of: overlay: unittest: overlay_bad_unresolved: Spelling s/ok/okay/
of: address: Consolidate bus .map() functions
of: address: Store number of bus flag cells rather than bool
of: unittest: Add tests for address translations
of: address: Remove duplicated functions
of: address: Fix address translation when address-size is greater than 2
dt-bindings: watchdog: cnxt,cx92755-wdt: convert txt to yaml
dt-bindings: watchdog: da9062-wdt: convert txt to yaml
dt-bindings: watchdog: fsl,scu-wdt: Document imx8dl
dt-bindings: watchdog: atmel,at91rm9200-wdt: convert txt to yaml
dt-bindings: usb: rockchip,dwc3: update inno usb2 phy binding name
...
All the properties described by video-interface-devices.yaml are
allowed for the image sensor, make them accepted by changing
"additionalProperties: false" to "unevaluatedProperties: false" at the
schema top-level.
Because all properties are now accepted, there is no need to explicitly
allow them in the schema.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
All the properties described by video-interface-devices.yaml are
allowed for the image sensor, make them accepted by changing
"additionalProperties: false" to "unevaluatedProperties: false" at the
schema top-level.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There is no reason to restrict the allowed rotation degrees to 0 and 180,
as the sensor can be mounted with any rotation.
Also, as all the properties described by video-interface-devices.yaml are
allowed for the image sensor, make them accepted by changing
"additionalProperties: false" to "unevaluatedProperties: false" at the
schema top-level.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
All the properties described by video-interface-devices.yaml are
allowed for the image sensor, make them accepted by changing
"additionalProperties: false" to "unevaluatedProperties: false" at the
schema top-level.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There is no reason to restrict the allowed rotation degrees to 0 and 180,
as the sensor can be mounted with any rotation.
Also, as all the properties described by video-interface-devices.yaml are
allowed for the image sensor, make them accepted by changing
"additionalProperties: false" to "unevaluatedProperties: false" at the
schema top-level.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Allow properties from video-interface-devices.yaml for the SK Hynix Hi-846
sensor.
All properties specified in video-interface-devices.yaml schema are
valid, so make them accepted by changing "additionalProperties: false"
to "unevaluatedProperties: false" at the schema top-level.
Add two properties from video-interface-devices.yaml to the example
to validate the new schema.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
As explained in the description text from trivial-devices.yaml:
"This is a list of trivial I2C and SPI devices that have simple device tree
bindings, consisting only of a compatible field, an address and possibly an
interrupt line."
A camera device does not fall into this category as it needs other
properties such as regulators, reset and powerdown GPIOs, clocks,
media endpoint.
Remove the OV5642 entry from trivial-devices.yaml and add its own
ovti,ov5642.yaml.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Pull more devicetree updates from Rob Herring:
"A couple of conversions which didn't get picked up by the subsystems
and one fix:
- Convert st,stih407-irq-syscfg and Omnivision OV7251 bindings to DT
schema
- Merge Omnivision OV5695 into OV5693 binding
- Fix of_overlay_fdt_apply prototype when !CONFIG_OF_OVERLAY"
* tag 'devicetree-fixes-for-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: irqchip: convert st,stih407-irq-syscfg to DT schema
media: dt-bindings: Convert Omnivision OV7251 to DT schema
media: dt-bindings: Merge OV5695 into OV5693 binding
of: overlay: Fix of_overlay_fdt_apply prototype when !CONFIG_OF_OVERLAY
Convert the OmniVision OV7251 Image Sensor binding to DT schema format.
vddd-supply was listed as required, but the example and actual user
don't have it. Also, the data brief says it has an internal regulator,
so perhaps it is truly optional.
Add missing common "link-frequencies" which is used and required by the
Linux driver.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Link: https://lore.kernel.org/r/20230817202713.2180195-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The OV5695 binding is almost the same as the OV5693 binding. The only
difference is 'clock-names' is defined for OV5695. However, the lack of
clock-names is an omission as the Linux OV5693 driver expects the same
'xvclk' clock name.
'link-frequencies' is required by OV5693, but not OV5695, so make that
conditional. Really, this shouldn't vary by device, but we're stuck with
the existing binding use.
The rockchip-isp1 binding example is missing required properties, so it
has to be updated as well.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230817202647.2179609-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Pull media updates from Mauro Carvalho Chehab:
- new i2c drivers: ds90ub913, ds90ub953, ds90ub960, dw9719, ds90ub913
- new Intel IVSC MEI drivers
- some Mediatek platform drivers were moved to a common location
- Intel atomisp2 driver is now working with the main ov2680 driver. Due
to that, the atomisp2 ov2680 staging one was removed
- the bttv driver was finally converted to videobuf2 framework. This
was the last one upstream using videobuf version 1 core. We'll likely
remove the old videobuf framework on 6.7
- lots of improvements at atomisp driver: it now works with normal I2C
sensors. Several compile-mode dependecies to select between ISP2400
and ISP2401 are now solved in runtime
- a new ipu-bridge logic was added to work with IVSC MEI drivers
- venus driver gained better support for new VPU versions
- the v4l core async framework has gained lots of improvements and
cleanups
- lots of other cleanups, improvements and driver fixes
* tag 'media/v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (358 commits)
media: ivsc: Add ACPI dependency
media: bttv: convert to vb2
media: bttv: use audio defaults for winfast2000
media: bttv: refactor bttv_set_dma()
media: bttv: move vbi_skip/vbi_count out of buffer
media: bttv: remove crop info from bttv_buffer
media: bttv: remove tvnorm field from bttv_buffer
media: bttv: remove format field from bttv_buffer
media: bttv: move do_crop flag out of bttv_fh
media: bttv: copy vbi_fmt from bttv_fh
media: bttv: copy vid fmt/width/height from fh
media: bttv: radio use v4l2_fh instead of bttv_fh
media: bttv: replace BUG with WARN_ON
media: bttv: use video_drvdata to get bttv
media: i2c: rdacm21: Fix uninitialized value
media: coda: Remove duplicated include
media: vivid: fix the racy dev->radio_tx_rds_owner
media: i2c: ccs: Check rules is non-NULL
media: i2c: ds90ub960: Fix PLL config for 1200 MHz CSI rate
media: i2c: ds90ub953: Fix use of uninitialized variables
...
The MAX96712 can support both a CSI-2 C-PHY and D-PHY bus. The initial
staging driver however only supported D-PHY and the bus-type property
was left optional.
In preparation for adding C-PHY support to the staging driver make the
bus-type property mandatory as it is needed to select the correct PHY
mode. Without the bus-type property present, the driver falls-back to
D-PHY mode, so the change is functionally backward compatible with old
DTS files lacking the property.
The only in-tree DTS file (renesas/r8a779a0-falcon-csi-dsi.dtsi) that
lacked the property uses D-PHY and have been updated.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Convert the text-based dt-bindings to yaml.
Changes from original txt:
* Take wording for various properties from other yaml bindings, this
removes e.g. volt amount from schema since it isn't really relevant
and the datasheet is a better source.
* Don't make reset-gpios a required property since it can be tied to
DOVDD instead.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
[Sakari Ailus: bump the maxItems for data-lanes to two]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The IMX290 module is available as either monochrome or colour and
the variant is not detectable at runtime.
Add a new compatible string for the monochrome version, based on the
full device name IMX290LLR. For consistency, add a new compatible string
for the colour version based on the IMX290LQR full device name, and
deprecate the current ambiguous compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
SPI and I2C bus node names are expected to be "spi" or "i2c",
respectively, with nothing else, a unit-address, or a '-N' index. A
pattern of 'spi0' or 'i2c0' or similar has crept in. Fix all these
cases. Mostly scripted with the following commands:
git grep -l '\si2c[0-9] {' Documentation/devicetree/ | xargs sed -i -e 's/i2c[0-9] {/i2c {/'
git grep -l '\sspi[0-9] {' Documentation/devicetree/ | xargs sed -i -e 's/spi[0-9] {/spi {/'
With this, a few errors in examples were exposed and fixed.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for the microchip,mcp251xfd.yaml
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for power-supply
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230228215433.3944508-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reference common HDMI CEC adapter properties to simplify the binding and
have only one place of definition for common properties. The common CEC
binding expects also node name to be 'cec'.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
