Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 14577/77836 datasheets describe the interrupt line as active
low with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and charger driver, so using
level sensitive interrupt is here especially important to avoid races.
With an edge configuration in case if first PMIC signals interrupt
followed shortly after by the RTC, the interrupt might not be yet
cleared/acked thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210602110445.33536-4-krzysztof.kozlowski@canonical.com
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 77693 datasheet describes the interrupt line as active low
with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210602110445.33536-3-krzysztof.kozlowski@canonical.com
Interrupt line can be configured on different hardware in different way,
even inverted. Therefore driver should not enforce specific trigger
type - edge falling - but instead rely on Devicetree to configure it.
The Maxim 77686 datasheet describes the interrupt line as active low
with a requirement of acknowledge from the CPU therefore the edge
falling is not correct.
The interrupt line is shared between PMIC and RTC driver, so using level
sensitive interrupt is here especially important to avoid races. With
an edge configuration in case if first PMIC signals interrupt followed
shortly after by the RTC, the interrupt might not be yet cleared/acked
thus the second one would not be noticed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210602110445.33536-2-krzysztof.kozlowski@canonical.com
The LogiCVC multi-function device has a display part which is now
described in its binding. Add a patternProperties match for it.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
CRU has a shared register that is used e.g. to control USB 2.0 PHY block
access. It's a single 32 b register. Document it as syscon so it can be
used with a regmap.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Broadcom's MISC is an MFD hardware block used on some of their SoCs like
bcm63xx and bcm4908. At this point only PCIe reset is fully understood
and documented. More functions may be added later.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull devicetree updates from Rob Herring:
- Convert /reserved-memory bindings to schemas
- Convert a bunch of NFC bindings to schemas
- Convert bindings to schema: Xilinx USB, Freescale DDR controller, Arm
CCI-400, UBlox Neo-6M, 1-Wire GPIO, MSI controller, ASpeed LPC, OMAP
and Inside-Secure HWRNG, register-bit-led, OV5640, Silead GSL1680,
Elan ekth3000, Marvell bluetooth, TI wlcore, TI bluetooth, ESP
ESP8089, tlm,trusted-foundations, Microchip cap11xx, Ralink SoCs and
boards, and TI sysc
- New binding schemas for: msi-ranges, Aspeed UART routing controller,
palmbus, Xylon LogiCVC display controller, Mediatek's MT7621 SDRAM
memory controller, and Apple M1 PCIe host
- Run schema checks for %.dtb targets
- Improve build time when using DT_SCHEMA_FILES
- Improve error message when dtschema is not found
- Various doc reference fixes in MAINTAINERS
- Convert architectures to common CPU h/w ID parsing function
of_get_cpu_hwid().
- Allow for empty NUMA node IDs which may be hotplugged
- Cleanup of __fdt_scan_reserved_mem()
- Constify device_node parameters
- Update dtc to upstream v1.6.1-19-g0a3a9d3449c8. Adds new checks
'node_name_vs_property_name' and 'interrupt_map'.
- Enable dtc 'unit_address_format' warning by default
- Fix unittest EXPECT text for gpio hog errors
* tag 'devicetree-for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (97 commits)
dt-bindings: net: ti,bluetooth: Document default max-speed
dt-bindings: pci: rcar-pci-ep: Document r8a7795
dt-bindings: net: qcom,ipa: IPA does support up to two iommus
of/fdt: Remove of_scan_flat_dt() usage for __fdt_scan_reserved_mem()
of: unittest: document intentional interrupt-map provider build warning
of: unittest: fix EXPECT text for gpio hog errors
of/unittest: Disable new dtc node_name_vs_property_name and interrupt_map warnings
scripts/dtc: Update to upstream version v1.6.1-19-g0a3a9d3449c8
dt-bindings: arm: firmware: tlm,trusted-foundations: Convert txt bindings to yaml
dt-bindings: display: tilcd: Fix endpoint addressing in example
dt-bindings: input: microchip,cap11xx: Convert txt bindings to yaml
dt-bindings: ufs: exynos-ufs: add exynosautov9 compatible
dt-bindings: ufs: exynos-ufs: add io-coherency property
dt-bindings: mips: convert Ralink SoCs and boards to schema
dt-bindings: display: xilinx: Fix example with psgtr
dt-bindings: net: nfc: nxp,pn544: Convert txt bindings to yaml
dt-bindings: Add a help message when dtschema tools are missing
dt-bindings: bus: ti-sysc: Update to use yaml binding
dt-bindings: sram: Allow numbers in sram region node name
dt-bindings: display: Document the Xylon LogiCVC display controller
...
This reverts commit 2ae80900f2.
My rework was unneeded & wrong. It replaced a clear & correct "reg"
property usage with a custom "offset" one.
Back then I didn't understand how to properly handle CRU block binding.
I heard / read about syscon and tried to use it in a totally invalid
way. That change also missed Rob's review (obviously).
Northstar's pin controller is a simple consistent hardware block that
can be cleanly mapped using a 0x24 long reg space.
Since the rework commit there wasn't any follow up modifying in-kernel
DTS files to use the new binding. Broadcom also isn't known to use that
bugged binding. There is close to zero chance this revert may actually
cause problems / regressions.
This commit is a simple revert. Example binding may (should) be updated
/ cleaned up but that can be handled separately.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211008205938.29925-1-zajec5@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Add support for registering devices via MFD cells to Simple MFD (I2C)
New Drivers:
- Add support for Renesas Synchronization Management Unit (SMU)
New Device Support:
- Add support for N5010 to Intel M10 BMC
- Add support for Cannon Lake to Intel LPSS ACPI
- Add support for Samsung SSG{1,2} to ST-Ericsson's U8500 family
- Add support for TQMx110EB and TQMxE40x to TQ-Systems PLD TQMx86
New Functionality:
- Add support for GPIO to Intel LPC ICH
- Add support for Reset to Texas Instruments TPS65086
Fix-ups:
- Trivial, sorting, whitespace, renaming, etc; mt6360-core, db8500-prcmu-regs, tqmx86
- Device Tree fiddling; syscon, axp20x, qcom,pm8008, ti,tps65086, brcm,cru
- Use proper APIs for IRQ map resolution; ab8500-core, stmpe, tc3589x, wm8994-irq
- Pass 'supplied-from' property through axp288_fuel_gauge via swnode
- Remove unused file entry; MAINTAINERS
- Make interrupt line optional; tps65086
- Rename db8500-cpuidle driver symbol; db8500-prcmu
- Remove support for unused hardware; tqmx86
- Provide a standard LPC clock frequency for unknown boards; tqmx86
- Remove unused code; ti_am335x_tscadc
- Use of_iomap() instead of ioremap(); syscon
Bug Fixes:
- Clear GPIO IRQ resource flags when no IRQ is set; tqmx86
- Fix incorrect/misleading frequencies; db8500-prcmu
- Mitigate namespace clash with other GPIOBASE users"
* tag 'mfd-next-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (31 commits)
mfd: lpc_sch: Rename GPIOBASE to prevent build error
mfd: syscon: Use of_iomap() instead of ioremap()
dt-bindings: mfd: Add Broadcom CRU
mfd: ti_am335x_tscadc: Delete superfluous error message
mfd: tqmx86: Assume 24MHz LPC clock for unknown boards
mfd: tqmx86: Add support for TQ-Systems DMI IDs
mfd: tqmx86: Add support for TQMx110EB and TQMxE40x
mfd: tqmx86: Fix typo in "platform"
mfd: tqmx86: Remove incorrect TQMx90UC board ID
mfd: tqmx86: Clear GPIO IRQ resource when no IRQ is set
mfd: simple-mfd-i2c: Add support for registering devices via MFD cells
mfd/cpuidle: ux500: Rename driver symbol
mfd: tps65086: Add cell entry for reset driver
mfd: tps65086: Make interrupt line optional
dt-bindings: mfd: Convert tps65086.txt to YAML
MAINTAINERS: Adjust ARM/NOMADIK/Ux500 ARCHITECTURES to file renaming
mfd: db8500-prcmu: Handle missing FW variant
mfd: db8500-prcmu: Rename register header
mfd: axp20x: Add supplied-from property to axp288_fuel_gauge cell
mfd: Don't use irq_create_mapping() to resolve a mapping
...
CRU is a block used in e.g. Northstar devices. It can be seen in the
bcm5301x.dtsi and this binding documents its proper usage.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The BeagleV Starlight v0.9 board[1] doesn't have the IRQB line routed to
the SoC, but it is still useful to be able to reach the PMIC over I2C
for the other functionality it provides such as GPIOs and regulator
settings.
[1] https://github.com/beagleboard/beaglev-starlight
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This converts the tps65086.txt binding description to YAML schema so
dts files can be verified automatically.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP305 PMIC used on many boards with the H616 SoC seems to be fully
compatible to the AXP805 PMIC, so add the proper chain of compatible
strings.
Also at least on one board (Orangepi Zero2) there is no interrupt line
connected to the CPU, so make the "interrupts" property optional.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull mfd updates from Lee Jones:
"Core Frameworks:
- Fix Software Node clean-up code
New Drivers:
- Add support for MediaTek MT6359 PMIC
- Add support for Qualcomm PM8008 PMIC
- Add support for Richtek RT4831
New Device Support:
- Add support for Audio CODECs to Rockchip RK817
- Add support for Alder Lake-M to Intel LPSS PCI
- Add support for Periph Device Charge to ChromeOS EC
New Functionality:
- Provide additional IRQs for wcd934x
- Add optional Reset functionality to lp87565
Fix-ups:
- Namespacing & visibility fixes to lp87565
- Differentiate between Power and Home key IRQs in mt6358
- Export I2C device tables in da9052-i2c, stmpe-i2c
- Adapt IRQ flags in max8907, rn5t61, max8907
- Make some functions/devices optional in axp20x, cros_ec_dev
- Explicitly include used header files in ioc3
- Remove superfluous lines in MAINTAINERS, sec-core, st,stm32-timers
- Resolve Kerneldoc issues in omap-usb-host, omap-usb-tll, si476x-cmd, si476x-i2c
- Convert arizona-core to a module
- Copyright changes in hi655x-pmic
- Drop support for board file initialisation in sec-core
- Trivial spelling, whitespace etc updates in lp87565, si476x-cmd,
mt6360-core, wm831x-core, twl-core, db8500-prcmu
- Simplify various implementations of wcd934x, mt6360-core, max8997,
max8998, da9052-i2c, da9062-core, sec-core,
- Device Tree binding changes in google,cros-ec,
richtek,rt4831-backlight, db8500-prcmu, qcom,pm8008, qcom,spmi-pmic
- Use provided APIs to simplify t7l66xb, as3722, da9055-core,
tps80031, 88pm800, 88pm805, asic3, sun6i-prcm, wm831x-core,
wm831x-otp, ucb1x00-assabet, timberdale, sm501, pcf50633-core,
kempld-core, janz-cmodio, intel_soc_pmic_bxtwc, ab8500-core
Bug Fixes:
- Fix unused variable warning in rk817_codec
- Fix regulator voltage configuration in rohm-bd71828
- Fix ongoing freeing of regmap_config 'name' issue in syscon
- Fix error handling path in da9063-i2c
- Fix Kconfig issues in MFD_MP2629
- Fix DMA mask warnings in motorola-cpcap"
* tag 'mfd-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (83 commits)
mfd: cros_ec: Add peripheral device charger
mfd: max8907: Remove IRQF_NO_AUTOEN flag
mfd: ab8500-core: Use DEVICE_ATTR_RO/RW macro
mfd: intel_soc_pmic_bxtwc: Use DEVICE_ATTR_ADMIN_RW macro
mfd: janz-cmodio: Use DEVICE_ATTR_RO macro
mfd: kempld-core: Use DEVICE_ATTR_RO macro
mfd: pcf50633: Use DEVICE_ATTR_ADMIN_RO macro
mfd: sm501: Use DEVICE_ATTR_RO macro
mfd: timberdale: Use DEVICE_ATTR_RO macro
mfd: ucb1x00-assabet: Use DEVICE_ATTR_RO macro
mfd: wm831x: Use DEVICE_ATTR_RO macro
mfd: wm831x: Use DEFINE_RES_IRQ_NAMED() and DEFINE_RES_IRQ() to simplify code
dt-bindings: mfd: stm32-timers: Remove #address/size cells from required properties
mfd: sun6i-prcm: Use DEFINE_RES_MEM() to simplify code
mfd: asic3: Use DEFINE_RES_MEM() and DEFINE_RES_IRQ() to simplify code
mfd: 88pm805: Use DEFINE_RES_IRQ_NAMED() to simplify code
mfd: 88pm800: Use DEFINE_RES_IRQ_NAMED() to simplify code
mfd: tps80031: Use DEFINE_RES_IRQ() to simplify code
mfd: da9055: Use DEFINE_RES_IRQ_NAMED() to simplify code
mfd: as3722: Use DEFINE_RES_IRQ_NAMED() to simplify code
...
Pull devicetree updates from Rob Herring:
- Refine reserved memory nomap handling
- Merge some PCI and non-PCI address handling implementations
- Simplify of_address.h header ifdefs
- Improve printk handling of some 64-bit types
- Convert adi,adv7511, Arm ccree, Arm SCMI, Arm SCU, Arm TWD timer, Arm
VIC, arm,sbsa-gwdt, Arm/Amlogic SCPI, Aspeed I2C, Broadcom iProc PWM,
linaro,optee-tz, MDIO GPIO, Mediatek RNG, MTD physmap, NXP
pcf8563/pcf85263/pcf85363, Renesas TPU, renesas,emev2-smu,
renesas,r9a06g032-sysctrl, sysc-rmobile, Tegra20 EMC, TI AM56 PCI, TI
OMAP mailbox, TI SCI bindings, virtio-mmio, Zynq FPGA, and ZynqMP RTC
to DT schema
- Convert mux and mux controller bindings to schema. This includes MDIO
IIO, and I2C muxes.
- Add Arm PL031 RTC binding schema
- Add vendor prefixes for StarFive Technology Co. Ltd. and Insignal Ltd
- Fix some stale doc references
- Remove stale property-units.txt. Superseded by schema in dt-schema
repo.
- Fixes for 'unevaluatedProperties' handling (enabled with experimental
json-schema support)
- Drop redundant usage of minItems and maxItems across the tree
- Update some examples to use bindings with a schema
* tag 'devicetree-for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (83 commits)
dt-bindings: Fix 'unevaluatedProperties' errors in DT graph users
dt-bindings: display: renesas,du: Fix 'ports' reference
dt-bindings: media: adv7180: Add missing video-interfaces.yaml reference
dt-bindings: crypto: ccree: Convert to json-schema
dt-bindings: fpga: zynq: convert bindings to YAML
dt-bindings: rtc: zynqmp: convert bindings to YAML
dt-bindings: interrupt-controller: Convert ARM VIC to json-schema
of: of_reserved_mem: mark nomap memory instead of removing
of: of_reserved_mem: only call memblock_free for normal reserved memory
dt-bindings: Drop redundant minItems/maxItems
dt-bindings: spmi: Correct 'reg' schema
of: reserved-memory: Add stub for RESERVEDMEM_OF_DECLARE()
dt-bindings: clk: vc5: Fix example
dt-bindings: timer: renesas,tmu: add r8a779a0 TMU support
dt-bindings: drm: bridge: adi,adv7511.txt: convert to yaml
dt-bindings: PCI: ti,am65: Convert PCIe host/endpoint mode dt-bindings to YAML
of: Remove superfluous casts when printing u64 values
of: Fix truncation of memory sizes on 32-bit platforms
dt-bindings: rtc: nxp,pcf8563: Absorb pcf85263/pcf85363 bindings
dt-bindings: pwm: Use examples with documented/matching schema
...
Pull sound updates from Takashi Iwai:
"As the diffstat scatters over the tree, we've got many tree-wide small
changes, but also got quite a few intrusive changes in the core side.
The only ABI-visible core change is the new rawmidi framing mode
support while others are kernel-internal, mostly code refactoring
and/or nice improvements.
Here are some highlights:
Core:
- A new framing access mode for rawmidi to get timestamps
- Cleanup / refactoring of buffer memory management helper code
- Support for automatic negotiation of ASoC DAI formats
- Revival of software suspend for PCM and control core, as a
preliminary work for PCI BAR rescan support
ASoC:
- Accessory detection support for several Qualcomm parts
- Support for IEC958 control with hdmi-codec
- Merging of Tegra machine drivers into a single driver
- Support for AmLogic SM1 TOACODEC, Intel AlderLake-M, several NXP
i.MX8 variants, NXP TFA1 and TDF9897, Rockchip RK817, Qualcomm
Quinary MI2S, Texas Instruments TAS2505
USB-audio:
- Reduction of latency at playback start
- Code cleanup / fixes of usx2y driver
- Scarlett2 mixer code fixes and enhancements
- Quirks for Ozone and Denon devices
HD-audio:
- A few quirks for HP and ASUS machines
- Display power management fixes
Others:
- FireWire code refactoring and enhancements
- Tree-wide trivial coding-style fixes"
* tag 'sound-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (594 commits)
ALSA: usb-audio: scarlett2: Fix for loop increment in scarlett2_usb_get_config
ALSA: hda/realtek: fix mute/micmute LEDs for HP ProBook 630 G8
ALSA: hda/realtek: fix mute/micmute LEDs for HP ProBook 445 G8
ALSA: hda/realtek: fix mute/micmute LEDs for HP ProBook 450 G8
ALSA: hda/realtek - Add ALC285 HP init procedure
ALSA: hda/realtek - Add type for ALC287
ALSA: scarlett2: Fix scarlett2_*_ctl_put() return values again
ALSA: scarlett2: Fix pad count for 18i8 Gen 3
ALSA: hda/realtek: fix mute/micmute LEDs for HP EliteBook 830 G8 Notebook PC
ALSA: firewire-lib: Fix 'amdtp_domain_start()' when no AMDTP_OUT_STREAM stream is found
ASoC: qcom: lpass-cpu: mark IRQ_CLEAR register as volatile and readable
ALSA: hda: Release codec display power during shutdown/reboot
ALSA: hda: Release controller display power during shutdown/reboot
ALSA: hda/realtek: Apply LED fixup for HP Dragonfly G1, too
ASoC: fsl: remove unnecessary oom message
ASoC: tlv320aic32x4: dt-bindings: add TAS2505 to compatible
ASoC: tlv320aic32x4: add support for TAS2505
ASoC: tlv320aic32x4: add type to device private data struct
ASoC: tegra30: ahub: Use devm_platform_get_and_ioremap_resource()
ASoC: tegra: tegra210_admaif: Use devm_platform_get_and_ioremap_resource()
...
This driver was merged in the early days of device tree
on Arm in 2012 and somehow we failed to provide bindings
for it. Fix it up with some YAML bindings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is for ChromeOS tablets which have a 'cros_cbas' switch device
in the "Whiskers" base board. This device can be instantiated only by
device tree on ARM platforms. ChromeOS EC doesn't provide a way to
probe the device.
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Immutable branch between MFD and ASoC due for the v5.14 merge window
Immutable branch between MFD, GPIO and Regulator due for the v5.14 merge window
Immutable branch between MFD, Regulator and RTC due for the v5.14 merge window
Create dt-binding documentation to document rk817 codec.
New property name of rockchip,mic-in-differential added to control if
the microphone is in differential mode or not.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Tested-by: Maciej Matuszczyk <maccraft123mc@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull pin control updates from Linus Walleij:
"There is a lot going on!
Core changes:
- A semantic change to handle pinmux and pinconf in explicit order
while up until now we depended on the semantic order in the device
tree. The device tree is a functional programming language and does
not imply any order, so the right thing is for the pin control core
to provide these semantics.
- Add a new pinmux-select debugfs file which makes it possible to go
in and select functions for a pin manually (iteratively, at the
prompt) for debugging purposes.
- Fixes to gpio regmap handling for a new pin control driver making
use of regmap-gpio.
- Use octal permissions on debugfs files.
New drivers:
- A massive rewrite of the former custom pin control driver for MIPS
Broadcom devices to instead use the pin control subsystem. New pin
control drivers for BCM6345, BCM6328, BCM6358, BCM6362, BCM6368,
BCM63268 and BCM6318 SoC variants are implemented.
- Support for PM8350, PM8350B, PM8350C, PMK8350, PMR735A and PMR735B
in the Qualcomm PMIC GPIO driver. Also the two GPIOs on PM8008 are
supported.
- Support for the Rockchip RK3568/RK3566 pin controller.
- Support for Ingenic JZ4730, JZ4750, JZ4755, JZ4775 and X2000.
- Support for Mediatek MTK8195.
- Add a new Xilinx ZynqMP pin control driver.
Driver improvements and non-urgent fixes:
- Modularization and improvements of the Rockchip drivers.
- Some new pins added to the description of new Renesas SoCs.
- Clarifications of the GPIO base calculation in the Intel driver.
- Fix the function names for the MPP54 and MPP55 pins in the Armada
CP110 pin controller.
- GPIO wakeup interrupt map for Qualcomm SC7280 and SM8350.
- Support for ACPI probing of the Qualcomm SC8180x.
- Fix interrupt clear status on rockchip
- Fix some missing pins on the Ingenic JZ4770, some semantic fixes
for the behaviour of the Ingenic pin controller. Add DMIC pins for
JZ4780, X1000, X1500 and X1830.
- A slew of janitorial like of_node_put() calls"
* tag 'pinctrl-v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: Add Xilinx ZynqMP pinctrl driver support
firmware: xilinx: Add pinctrl support
pinctrl: rockchip: do coding style for mux route struct
pinctrl: Add PIN_CONFIG_MODE_PWM to enum pin_config_param
pinctrl: Introduce MODE group in enum pin_config_param
pinctrl: Keep enum pin_config_param ordered by name
dt-bindings: pinctrl: Add binding for ZynqMP pinctrl driver
pinctrl: core: Fix kernel doc string for pin_get_name()
pinctrl: mediatek: use spin lock in mtk_rmw
pinctrl: add drive for I2C related pins on MT8195
pinctrl: add pinctrl driver on mt8195
dt-bindings: pinctrl: mt8195: add pinctrl file and binding document
pinctrl: Ingenic: Add pinctrl driver for X2000.
pinctrl: Ingenic: Add pinctrl driver for JZ4775.
pinctrl: Ingenic: Add pinctrl driver for JZ4755.
pinctrl: Ingenic: Add pinctrl driver for JZ4750.
pinctrl: Ingenic: Add pinctrl driver for JZ4730.
dt-bindings: pinctrl: Add bindings for new Ingenic SoCs.
pinctrl: Ingenic: Reformat the code.
pinctrl: Ingenic: Add DMIC pins support for Ingenic SoCs.
...
Pull MFD updates from Lee Jones:
"Core Framework:
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
New Drivers:
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
New Device Support:
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
Removed Device Support:
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
New Functionality:
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
New/converted Device Tree bindings:
- rohm bd71815-pmic, rohm bd9576-pmic, netronix ntxec, actions
atc260x, ricoh rn5t618, qcom pm8xxx
- Fix-ups:
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618,
max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci, atc260x-i2c, intel_quark_i2c_gpio
Bug Fixes:
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers"
* tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (84 commits)
mfd: intel-m10-bmc: Add support for MAX10 BMC Secure Updates
Revert "mfd: max8997: Add of_compatible to Extcon and Charger mfd_cell"
mfd: twl: Remove unused inline function twl4030charger_usb_en()
dt-bindings: mfd: Convert pm8xxx bindings to yaml
dt-bindings: mfd: Add compatible for pmk8350 rtc
i2c: designware: Get rid of legacy platform data
mfd: intel_quark_i2c_gpio: Convert I²C to use software nodes
mfd: lpc_sch: Partially revert "Add support for Intel Quark X1000"
mfd: arizona: Fix rumtime PM imbalance on error
mfd: max8997: Replace 8998 with 8997
mfd: core: Use acpi_find_child_device() for child devices lookup
mfd: intel_quark_i2c_gpio: Don't play dirty trick with const
mfd: intel_quark_i2c_gpio: Enable MSI interrupt
mfd: intel_quark_i2c_gpio: Reuse BAR definitions for MFD cell indexing
mfd: ntxec: Support for EC in Tolino Shine 2 HD
mfd: stm32-timers: Avoid clearing auto reload register
mfd: intel_quark_i2c_gpio: Replace I²C speeds with descriptive definitions
mfd: intel_quark_i2c_gpio: Remove unused struct device member
mfd: intel_quark_i2c_gpio: Unregister resources in reversed order
mfd: Kconfig: ABX500_CORE should depend on ARCH_U8500
...
