Pull remoteproc updates from Bjorn Andersson:
- The i.MX DSP remoteproc driver adds support for providing a resource
table, in order to enable IPC with the core
- The TI K3 DSP driver is transitioned to remove_new, error messages
are changed to use symbolic error codes, and dev_err_probe() is used
where applicable
- Support for the Qualcomm SC7280 audio, compute and WiFi co-processors
are added to the Qualcomm TrustZone based remoteproc driver
* tag 'rproc-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
remoteproc: qcom_q6v5_pas: Add SC7280 ADSP, CDSP & WPSS
dt-bindings: remoteproc: qcom: sc7180-pas: Add SC7280 compatibles
dt-bindings: remoteproc: qcom: sc7180-pas: Fix SC7280 MPSS PD-names
remoteproc: k3-dsp: Convert to platform remove callback returning void
remoteproc: k3-dsp: Use symbolic error codes in error messages
remoteproc: k3-dsp: Suppress duplicate error message in .remove()
arm64: dts: imx8mp: Add reserve-memory nodes for DSP
remoteproc: imx_dsp_rproc: Add mandatory find_loaded_rsc_table op
Pull remoteproc updates from Bjorn Andersson:
"Support for controlling the second core in Mediatek's SCP dual-core
setup is introduced.
Support for audio, compute and modem DSPs on Qualcomm SM6375, and the
audio DSP in SC7180 are introduced. The peripheral NoC clock is
dropped from MSM8996 modem DSP, as this is handled through the
interconnect provider.
In the zynqmp driver the setup for TCM memory, and device address
translation thereof, when operating in lockstep mode is corrected.
A few bug fixes and cleanups are introduces across the ST and STM32
remoteproc drivers"
* tag 'rproc-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (28 commits)
remoteproc: st: Fix sometimes uninitialized ret in st_rproc_probe()
remoteproc: st: Use device_get_match_data()
remoteproc: zynqmp: Change tcm address translation method
remoteproc: mediatek: Refactor single core check and fix retrocompatibility
remoteproc: qcom: q6v5-mss: Remove PNoC clock from 8996 MSS
dt-bindings: remoteproc: qcom,msm8996-mss-pil: Remove PNoC clock
dt-bindings: remoteproc: qcom,adsp: Remove AGGRE2 clock
remoteproc: qcom: pas: Add SM6375 MPSS
remoteproc: qcom: pas: Add SM6375 ADSP & CDSP
dt-bindings: remoteproc: qcom,sm6375-pas: Document remoteprocs
dt-bindings: remoteproc: pru: Add Interrupt property
remoteproc: qcom: pas: Add sc7180 adsp
dt-bindings: remoteproc: qcom: sc7180-pas: Add ADSP compatible
arm64: dts: mediatek: Update the node name of SCP rpmsg subnode
remoteproc: zynqmp: fix TCM carveouts in lockstep mode
remoteproc: mediatek: Refine ipi handler error message
remoteproc: mediatek: Report watchdog crash to all cores
remoteproc: mediatek: Handle MT8195 SCP core 1 watchdog timeout
remoteproc: mediatek: Setup MT8195 SCP core 1 SRAM offset
remoteproc: mediatek: Remove dependency of MT8195 SCP L2TCM power control on dual-core SCP
...
The common reserved-memory bindings have recently been copied from the
kernel tree into dtschema. The preference is to host common, stable
bindings in dtschema. As reserved-memory is documented in the DT Spec,
it meets the criteria.
The v2023.09 version of dtschema is what contains the reserved-memory
schemas we depend on, so bump the minimum version to that. Otherwise,
references to these schemas will generate errors.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: https://lore.kernel.org/r/20231013200851.347042-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Pull remoteproc updates from Bjorn Andersson:
"Support for booting the iMX remoteprocs using MMIO, instead of SMCCC
is added. The iMX driver is also extended to support delivering
interrupts from an arbitrary number of vdev.
Support is added to the TI PRU driver, to allow GPMUX to be controlled
from DeviceTree.
The Qualcomm coredump collector is extended to fall back to generating
a full coredump, in the case that the loaded firmware doesn't support
generating minidump. The overly terse MD abbreviation of "MINIDUMP" is
expanded, to make the code easier on the eye.
The list of Qualcomm Sensor Low Power Island (SLPI) instances
supported is cleaned up, and SDM845 is added. SDM630/636/660 support
for the modem subsystem (mss) is added.
All the Qualcomm drivers are transitioned to of_reserved_mem_lookup()
instead of open coding the resolution of reserved-memory regions, to
gain handling of error cases. A couple of drivers are transitioned to
use devm_platform_ioremap_resource_byname().
The stm32 remoteproc driver's PM operations are updated to modern
macros, to avoid the "unused variable"-warning in some configurations.
Drivers are transitioned away from directly including of_device.h"
* tag 'rproc-v6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (23 commits)
remoteproc: pru: add support for configuring GPMUX based on client setup
remoteproc: stm32: fix incorrect optional pointers
remoteproc: imx_rproc: Switch iMX8MN/MP from SMCCC to MMIO
dt-bindings: remoteproc: imx_rproc: Support i.MX8MN/P MMIO
dt-bindings: remoteproc: qcom,msm8996-mss-pil: Fix 8996 clocks
remoteproc: qcom: pas: add SDM845 SLPI compatible
remoteproc: qcom: q6v5-mss: Add support for SDM630/636/660
dt-bindings: remoteproc: qcom,msm8996-mss-pil: Add SDM660 compatible
remoteproc: qcom: Expand MD_* as MINIDUMP_*
remoteproc: qcom: pas: refactor SLPI remoteproc init
dt-bindings: remoteproc: qcom: adsp: add qcom,sdm845-slpi-pas compatible
remoteproc: qcom: wcnss: use devm_platform_ioremap_resource_byname()
remoteproc: qcom: q6v5: use devm_platform_ioremap_resource_byname()
dt-bindings: remoteproc: qcom: sm6115-pas: Add QCM2290
remoteproc: qcom: Add full coredump fallback mechanism
remoteproc: core: Export the rproc coredump APIs
remoteproc: qcom: Use of_reserved_mem_lookup()
remoteproc: imx_rproc: iterate all notifiyids in rx callback
dt-bindings: remoteproc: qcom,adsp: bring back firmware-name
dt-bindings: remoteproc: qcom,sm8550-pas: require memory-region
...
Pull devicetree updates from Rob Herring:
"DT core:
- Add support for generating DT nodes for PCI devices. This is the
groundwork for applying overlays to PCI devices containing
non-discoverable downstream devices.
- DT unittest additions to check reverted changesets, to test for
refcount issues, and to test unresolved symbols. Also, various
clean-ups of the unittest along the way.
- Refactor node and property manipulation functions to better share
code with old API and changeset API
- Refactor changeset print functions to a common implementation
- Move some platform_device specific functions into of_platform.c
Bindings:
- Treewide fixing of typos
- Treewide clean-up of SPDX tags to use 'OR' consistently
- Last chunk of dropping unnecessary quotes. With that, the check for
unnecessary quotes is enabled in yamllint.
- Convert ftgmac100, zynqmp-genpd, pps-gpio, syna,rmi4, and qcom,ssbi
bindings to DT schema format
- Add Allwinner V3s xHCI USB, Saef SF-TC154B display, QCom SM8450
Inline Crypto Engine, QCom SM6115 UFS, QCom SDM670 PDC interrupt
controller, Arm 2022 Cortex cores, and QCom IPQ9574 Crypto bindings
- Fixes for Rockchip DWC PCI binding
- Ensure all properties are evaluated on USB connector schema
- Fix dt-check-compatible script to find of_device_id instances with
compiler annotations"
* tag 'devicetree-for-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (64 commits)
dt-bindings: usb: Add V3s compatible string for OHCI
dt-bindings: usb: Add V3s compatible string for EHCI
dt-bindings: display: panel: mipi-dbi-spi: add Saef SF-TC154B
dt-bindings: vendor-prefixes: document Saef Technology
dt-bindings: thermal: lmh: update maintainer address
of: unittest: Fix of_unittest_pci_node() kconfig dependencies
dt-bindings: crypto: ice: Document sm8450 inline crypto engine
dt-bindings: ufs: qcom: Add ICE to sm8450 example
dt-bindings: ufs: qcom: Add sm6115 binding
dt-bindings: ufs: qcom: Add reg-names property for ICE
dt-bindings: yamllint: Enable quoted string check
dt-bindings: Drop remaining unneeded quotes
of: unittest-data: Fix whitespace - angular brackets
of: unittest-data: Fix whitespace - indentation
of: unittest-data: Fix whitespace - blank lines
of: unittest-data: Convert remaining overlay DTS files to sugar syntax
of: overlay: unittest: Add test for unresolved symbol
of: unittest: Add separators to of_unittest_overlay_high_level()
of: unittest: Cleanup partially-applied overlays
of: unittest: Merge of_unittest_apply{,_revert}_overlay_check()
...
Documentation/process/license-rules.rst and checkpatch expect the SPDX
identifier syntax for multiple licenses to use capital "OR". Correct it
to keep consistent format and avoid copy-paste issues.
Correct also the format // -> .* in few Allwinner binding headers as
pointed out by checkpatch:
WARNING: Improper SPDX comment style for 'include/dt-bindings/reset/sun50i-h6-ccu.h', please use '/*' instead
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230823084540.112602-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
The MX8M CM7 boot via SMC call is problematic, since not all versions
of ATF support this interface. Document MMIO support used to boot the
CM7 on MX8MN/MP instead and discern MMIO interface using DT compatible
string. Document GPR register syscon phandle which is required by the
MMIO interface too.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230724222418.163220-1-marex@denx.de
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
QCM2290 is more or less a fork of the same design that SM6115 is based
on. As a result, the ADSP and modem found on it are identical.
Add compatibles for the QCM2290 with SM6115 fallbacks so as not to
require any driver changes. Change the allOf:if:properties clauses
to look for the presence of SM6115 compatibles and not an exact match.
Note that QCM2290 lacks a CDSP.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230315183231.3562580-1-konrad.dybcio@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
On Qualcomm platforms, most subsystems (e.g. audio/modem DSP) are
described as remote processors in the device tree, with a dedicated
node where properties and services related to them can be described.
The Resource Power Manager (RPM) is also such a subsystem, with a
remote processor that is running a special firmware. Unfortunately,
the RPM never got a dedicated node representing it properly in the
device tree. Most of the RPM services are described below a top-level
/smd or /rpm-glink node.
However, SMD/GLINK is just one of the communication channels to the RPM
firmware. For example, the MPM interrupt functionality provided by the
RPM does not use SMD/GLINK but writes directly to a special memory
region allocated by the RPM firmware in combination with a mailbox.
Currently there is no good place in the device tree to describe this
functionality. It doesn't belong below SMD/GLINK but it's not an
independent top-level device either.
Introduce a new "qcom,rpm-proc" compatible that allows describing the
RPM as a remote processor/subsystem like all others. The SMD/GLINK node
is moved to a "smd-edge"/"glink-edge" subnode consistent with other
existing bindings. Additional subnodes (e.g. interrupt-controller for
MPM, rpm-master-stats) can be also added there.
Deprecate using the old top-level /smd node since all SMD edges
are now specified as subnodes of the remote processor.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230531-rpm-rproc-v3-6-a07dcdefd918@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Semantically glink-edge and glink-rpm-edge are similar: Both describe
the communication channels to a remote processor. The RPM glink-edge is
a special case that needs slightly different properties but otherwise
it is used exactly the same.
To improve consistency use the same "glink-edge" node name also for
glink-rpm-edge. Drop the $nodename from qcom,glink-edge.yaml to avoid
matching the wrong schema. qcom,glink-edge.yaml is always referenced
explicitly from other schemas. This will already ensure that the nodes
are being checked, so it's not necessary to bind to all nodes named
"glink-edge".
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230531-rpm-rproc-v3-5-a07dcdefd918@gerhold.net
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Pull more devicetree updates from Rob Herring:
- Whitespace clean-ups in binding examples
- Restrict node name suffixes to "-[0-9]+" for cases of multiple
instances which don't have unit-addresses
- Convert brcm,kona-wdt and cdns,wdt-r1p2 watchdog bindings to DT
schema
* tag 'devicetree-for-6.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: soc: qcom: stats: Update maintainer email
dt-bindings: cleanup DTS example whitespaces
dt-bindings: timestamp: restrict node name suffixes
dt-bindings: slimbus: restrict node name suffixes
dt-bindings: watchdog: restrict node name suffixes
dt-bindings: watchdog: brcm,kona-wdt: convert txt file to yaml
dt-bindings: watchdog: cdns,wdt-r1p2: Convert cadence watchdog to yaml
Pull remoteproc updates from Bjorn Andersson:
"The bulk of these patches relates to the moving to a void-returning
remove callback.
The i.MX HiFi remoteproc driver gets its pm_ops helpers updated to
resolve build warnings about 'defined but not used' variables in
certain configurations.
The ST STM32 remoteproc driver is extended to allow using a SCMI reset
controller to hold boot, and has an error message corrected.
The Qualcomm Q6V5 PAS driver gains a missing 'static' qualifier on
adsp_segment_dump()"
* tag 'rproc-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (23 commits)
remoteproc: qcom_q6v5_pas: staticize adsp_segment_dump()
remoteproc: stm32: Fix error code in stm32_rproc_parse_dt()
remoteproc: stm32: Allow hold boot management by the SCMI reset controller
dt-bindings: remoteproc: st,stm32-rproc: Rework reset declarations
remoteproc: imx_dsp_rproc: use modern pm_ops
remoteproc: wkup_m3: Convert to platform remove callback returning void
remoteproc: stm32: Convert to platform remove callback returning void
remoteproc: st: Convert to platform remove callback returning void
remoteproc: virtio: Convert to platform remove callback returning void
remoteproc: rcar: Convert to platform remove callback returning void
remoteproc: qcom_wcnss: Convert to platform remove callback returning void
remoteproc: qcom_q6v5_wcss: Convert to platform remove callback returning void
remoteproc: qcom_q6v5_pas: Convert to platform remove callback returning void
remoteproc: qcom_q6v5_mss: Convert to platform remove callback returning void
remoteproc: qcom_q6v5_adsp: Convert to platform remove callback returning void
remoteproc: pru: Convert to platform remove callback returning void
remoteproc: omap: Convert to platform remove callback returning void
remoteproc: mtk_scp: Convert to platform remove callback returning void
remoteproc: meson_mx_ao_arc: Convert to platform remove callback returning void
remoteproc: keystone: Convert to platform remove callback returning void
...
With the introduction of the SCMI (System Control and Management
Interface), it is now possible to use the SCMI to handle the
hold boot instead of a dedicated SMC call.
As consequence two configurations are possible:
- without SCMI server on OP-TEE:
use the Linux rcc reset service and use syscon for the MCU hold boot
- With SCMI server on OP-TEE:
use the SCMI reset service for both the MCU reset and the MCU hold boot.
This patch:
- make optional and deprecated the use of the property st,syscfg-tz
which was used to check if the trusted Zone was enable to use scm call,
to manage the hold boot. The reset controller phandle is used instead
to select the configurations.
- make st,syscfg-holdboot optional
- adds properties check on resets definitions.
- adds an example of the SCMI reset service usage.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230512093926.661509-2-arnaud.pouliquen@foss.st.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
AM62 family of devices don't have a R5F cluster, instead they have
single core DM R5F. Add new compatible string ti,am62-r5fss to support
this scenario.
When this new compatible is used cluster-mode property can only be set
to value 3 i.e. CLUSTER_MODE_SINGLECORE which is also the default value
in case cluster-mode is not defined in device-tree.
While at it, also sort the compatible lists in alphabetical order.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Link: https://lore.kernel.org/r/20230327152832.923480-3-devarsht@ti.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Pull remoteproc updates from Bjorn Andersson:
- Support for PRU clients to acquire a control reference to the PRU
instances is introduced, and the PRU now allows specifying
firmware-name in Devicetree. sysfs is requested to be read-only when
the remoteproc instance is consumed by another kernel driver
- Support for the C7xv DSP on AM62A SoC is introduced
- The Devicetree binding for the Qualcomm PAS devices are split up in
multiple files, to better account for the differences in resources
between them. A number of missing Devicetree bindings are added, and
the Qualcomm WCNSS binding is converted to YAML
- A few cleanups are introduced for the Mediatek SCP driver. And a
sanity check of the firmware image is introduced in the Mediatek
driver
- For Qualcomm SC7280 ADSP support is added, MSM8953 gains ADSP and
modem support, SM6115 and SM8550 gains ADSP, CDSP and modem support,
and support for pronto v3 support (used on e.g. MSM8953) is added
- The Qualcomm modem remoteproc driver is modified to use a no-map
reserved-memory region for it's authentication metadata, in order to
avoid fatal security violations caused by accesses from Linux during
the authentication process
- Support for separate loading of a Devicetree blob is added to the PAS
driver, and support for the PAS driver to carve out DSM memory for
the modem is added as well
- The Qualcomm ADSP remoteproc driver gains support for mapping memory
into specific range using the IOMMU. The sysmon driver is
transitioned to strlcpy()
* tag 'rproc-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (69 commits)
dt-bindings: mailbox: qcom,apcs-kpss-global: drop mbox-names from example
dt-bindings: remoteproc: qcom,glink-edge: correct label description
dt-bindings: remoteproc: qcom,glink-rpm-edge: convert to DT schema
dt-bindings: remoteproc: qcom,sm8550-pas: correct power domains
remoteproc: qcom_q6v5_pas: enable sm8550 adsp & cdsp autoboot
dt-bindings: remoteproc: qcom: Add sm6115 pas yaml file
remoteproc: qcom: pas: Add sm6115 remoteprocs
remoteproc: qcom: pas: Adjust the phys addr wrt the mem region
remoteproc: qcom: fix sparse warnings
remoteproc: qcom: replace kstrdup with kstrndup
remoteproc: mediatek: Check the SCP image format
remoteproc: qcom_q6v5_mss: Use a carveout to authenticate modem headers
Revert "remoteproc: qcom_q6v5_mss: map/unmap metadata region before/after use"
dt-bindings: remoteproc: qcom,sc7280-mss-pil: Update memory-region
dt-bindings: remoteproc: qcom,sc7180-mss-pil: Update memory-region
dt-bindings: remoteproc: qcom,msm8996-mss-pil: Update memory region
dt-bindings: remoteproc: qcom,q6v5: Move MSM8996 to schema
remoteproc: qcom_q6v5_pas: add sm8550 adsp, cdsp & mpss compatible & data
remoteproc: qcom_q6v5_pas: add support for assigning memory to firmware
remoteproc: qcom_q6v5_pas: add support for dtb co-firmware loading
...
Pull rpmsg updates from Bjorn Andersson:
- rpmsg ctrl and char driver locking is ensure ordering in cases where
the communication link is being torn down in parallel with calls to
open(2) or poll(2)
- The glink driver is refactored, to move rpm/smem-specifics out of the
common logic and better suite further improvements, such as
transports without a mailbox controller. The handling of remoteproc
shutdown is improved, to fail clients immediately instead of having
them to wait for timeouts. A driver_override memory leak is corrected
and a few spelling improvements are introduced
- glink_ssr is transitioned off strlcpy() and "gpr" is added as a valid
child node of the glink-edge DT binding
* tag 'rpmsg-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
rpmsg: glink: Release driver_override
rpmsg: glink: Avoid infinite loop on intent for missing channel
rpmsg: glink: Fix GLINK command prefix
rpmsg: glink: Fix spelling of peek
rpmsg: glink: Cancel pending intent requests at removal
rpmsg: glink: Fail qcom_glink_tx() once remove has been initiated
rpmsg: glink: Move irq and mbox handling to transports
rpmsg: glink: rpm: Wrap driver context
rpmsg: glink: smem: Wrap driver context
rpmsg: glink: Extract tx kick operation
rpmsg: glink: Include types in qcom_glink_native.h
rpmsg: ctrl: Add lock to rpmsg_ctrldev_remove
rpmsg: char: Add lock to avoid race when rpmsg device is released
rpmsg: move from strlcpy with unused retval to strscpy
dt-bindings: remoteproc: qcom,glink-edge: add GPR node
Convert Qualcomm G-Link RPM edge binding to DT schema. Move it to
remoteproc as it better suits the purpose - communication channel with
remote processor.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
