Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
A small update for SDW machine support:
Small fixes for sof_sdw machine driver
Support for rt722
New TGL/MTL and LNL match for new configurations
Thomas Zimermann needs 8d6ef26501 ("drm/ast: Disconnect BMC if
physical connector is connected") for further ast work in -next.
Minor conflicts in ivpu between 3de6d95978 ("accel/ivpu: Pass D0i3
residency time to the VPU firmware") and 3f7c063492
("accel/ivpu/37xx: Fix hangs related to MMIO reset") changing adjacent
lines.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Current binding has following compatible combination for SoM, IO board
- NCM6A: edgeble,neural-compute-module-6a,
edgeble,neural-compute-module-6a-io
- NCM6B: edgeble,neural-compute-module-6b,
edgeble,neural-compute-module-6b-io
This board topology now changes in final revisions, so a common
compatible IO board, NCM6A-IO, is made available for both variants
of SoM: NCM6A and NCM6B, produced by Edgeble AI.
With this change, 6b-io is not as available and 6a; 6b SoM's have the
same compatible IO board as 6a-io. This change is due to the common
optimised design of the IO board made available now in final revisions,
which was not the case in initial revisions.
Update the dt-bindings with this new change.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231125142914.57459-1-jagan@edgeble.ai
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Let's add compatibles for some xyboard tablets, these are similar to
the mapphone devices already listed but with different peripherals.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The amlogic,g12a-mipi-dphy-analog is a feature of the simple-mfd
amlogic,meson-axg-hhi-sysctrl system control register zone which is an
intermixed registers zone, thus it's very hard to define clear ranges for
each SoC controlled features even if possible.
The amlogic,g12a-mipi-dphy-analog was wrongly documented as an independent
register range, which is not the reality, thus fix the bindings by dropping
the reg property now it's referred from amlogic,meson-gx-hhi-sysctrl.yaml
and documented as a subnode of amlogic,meson-axg-hhi-sysctrl.
Also drop the unnecessary example, the top level bindings example should
be enough.
Fixes: 76ab79f972 ("dt-bindings: phy: add Amlogic G12A Analog MIPI D-PHY bindings")
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231124-amlogic-v6-4-upstream-dsi-ccf-vim3-v9-4-95256ed139e6@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We need the USB/PHY/Thunderbolt fixes in here as well for later patches
to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Johan writes:
USB-serial fixes for 6.7-rc3
Here are a couple of modem device entry fixes and some new modem device
ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.7-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (329 commits)
USB: serial: option: add Luat Air72*U series products
USB: serial: option: add Fibocom L7xx modules
USB: serial: option: fix FM101R-GL defines
USB: serial: option: don't claim interface 4 for ZTE MF290
Linux 6.7-rc2
prctl: Disable prctl(PR_SET_MDWE) on parisc
parisc/power: Fix power soft-off when running on qemu
parisc: Replace strlcpy() with strscpy()
NFSD: Fix checksum mismatches in the duplicate reply cache
NFSD: Fix "start of NFS reply" pointer passed to nfsd_cache_update()
NFSD: Update nfsd_cache_append() to use xdr_stream
nfsd: fix file memleak on client_opens_release
dm-crypt: start allocating with MAX_ORDER
dm-verity: don't use blocking calls from tasklets
dm-bufio: fix no-sleep mode
dm-delay: avoid duplicate logic
dm-delay: fix bugs introduced by kthread mode
dm-delay: fix a race between delay_presuspend and delay_bio
drm/amdgpu/gmc9: disable AGP aperture
drm/amdgpu/gmc10: disable AGP aperture
...
Unified DMA (UDMA) module on K3 SoCs have TX and RX channel cfg and RX
flow cfg register regions which are usually configured by a Device
Management firmware. But certain entities such as bootloader (like
U-Boot) may have to access them directly. Describe this region in the
binding documentation for completeness of module description.
Keep the binding compatible with existing DTS files by requiring first
four regions to be present at least.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231124045722.191817-5-vigneshr@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Packet DMA (PKTDMA) module on K3 SoCs have ring cfg, TX and RX channel
cfg and RX flow cfg register regions which are usually configured by a
Device Management firmware. But certain entities such as bootloader
(like U-Boot) may have to access them directly. Describe this region in
the binding documentation for completeness of module description.
Keep the binding compatible with existing DTS files by requiring first
four regions to be present at least.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231124045722.191817-4-vigneshr@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Block copy DMA(BCDMA)module on K3 SoCs have ring, BCHAN, TX and RX
channel cfg register regions which are usually configured by a Device
Management firmware. But certain entities such as bootloader (like
U-Boot) may have to access them directly. Describe this region in the
binding documentation for completeness of module description.
Keep the binding compatible with existing DTS files by requiring first
five regions to be present at least.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231124045722.191817-3-vigneshr@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Older ARM8 SoCs like Exynos5433, Exynos7 and Exynos7885 have the pin
controller with wake-up interrupts muxed, thus the wake-up interrupt
controller device node has interrupts property, while its pin banks
might not (because they are muxed by the wake-up controller).
Newer SoCs like Exynos850 and ExynosAutov9 do not used muxed wake-up
interrupts:
1. Wake-up interrupt controller device node has no interrupts,
2. Its pin banks have interrupts (since there is no muxing).
Their programming interface is however still compatible with Exynos7,
thus change the bindings to express this: retain compatibility with
Exynos7 and add new compatibility fallback of Exynos850 in newer
designs.
No driver changes are needed. This is necessary only to properly
describe DTS.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Jaewon Kim <jaewon02.kim@samsung.com>
Link: https://lore.kernel.org/r/20231122200407.423264-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
* icc-x1e80100
dt-bindings: interconnect: document the RPMh Network-On-Chip Interconnect in Qualcomm SM8650 SoC
interconnect: qcom: introduce RPMh Network-On-Chip Interconnect on SM8650 SoC
dt-bindings: interconnect: qcom-bwmon: document SM8650 BWMONs
This series adds interconnect support for the Qualcomm X1E80100 platform,
aka Snapdragon X Elite.
Our v1 post of the patchsets adding support for Snapdragon X Elite SoC had
the part number sc8380xp which is now updated to the new part number x1e80100
based on the new branding scheme and refers to the exact same SoC.
Release Link: https://www.qualcomm.com/news/releases/2023/10/qualcomm-unleashes-snapdragon-x-elite--the-ai-super-charged-plat
Link: https://lore.kernel.org/r/20231123135028.29433-1-quic_sibis@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
The two properties:
- max-brightness
- default brightness
are not really required, so they can be removed from the "required"
section.
The "max-brightness" is no longer used in the current version
of the driver (it was used only in the first version).
The "default-brightness", if omitted in the DT, is managed by the
device driver, using a default value. This value depends on the dimming
mode used:
- for the "analog mode", via I2C commands, this value is fixed by
hardware (=31)
- while in case of pwm mode the default used is the last value of the
brightness-levels array.
Also the brightness-levels array is not required:
- in "analog mode", via I2C commands, the brightness-level array is
fixed by hardware (0..31).;
- in pwm dimming mode, the driver uses a default array of 0..255 and
the "default-brightness" is the last one, which is "255"
NOTE: there are no compatibility problems with the previous version,
since the device driver has not yet been included in any kernel.
Only this dt-binding yaml file is already included in the current
v6.7.0-rc1 kernel version.
No developer may have used it.
Other changes:
- improve the backlight working mode description, in the "description"
section
- update the example, removing the "max-brightness" and introducing the
"brightess-levels" property
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20231116105319.957600-2-f.suligoi@asem.it
Signed-off-by: Lee Jones <lee@kernel.org>
Linux 6.7-rc2
* tag 'v6.7-rc2': (325 commits)
Linux 6.7-rc2
prctl: Disable prctl(PR_SET_MDWE) on parisc
parisc/power: Fix power soft-off when running on qemu
parisc: Replace strlcpy() with strscpy()
NFSD: Fix checksum mismatches in the duplicate reply cache
NFSD: Fix "start of NFS reply" pointer passed to nfsd_cache_update()
NFSD: Update nfsd_cache_append() to use xdr_stream
nfsd: fix file memleak on client_opens_release
dm-crypt: start allocating with MAX_ORDER
dm-verity: don't use blocking calls from tasklets
dm-bufio: fix no-sleep mode
dm-delay: avoid duplicate logic
dm-delay: fix bugs introduced by kthread mode
dm-delay: fix a race between delay_presuspend and delay_bio
drm/amdgpu/gmc9: disable AGP aperture
drm/amdgpu/gmc10: disable AGP aperture
drm/amdgpu/gmc11: disable AGP aperture
drm/amdgpu: add a module parameter to control the AGP aperture
drm/amdgpu/gmc11: fix logic typo in AGP check
drm/amd/display: Fix encoder disable logic
...
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This cache controller is also used on the StarFive JH7100 SoC.
Unfortunately it needs a quirk to work properly, so add dedicated
compatible string to be able to match it.
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
