Clearfog GTR has an official enclosure with labels for all interfaces.
The "lan" ports on the 8-port switch in device-tree were numbered in
reverse wrt. enclosure.
Update all device-tree labels to match.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Clearfog GTR L8 has an extra SFP connector on the managed switch port 9.
Add descriptions for both entities along with pinctrl.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Minor improvements in ARM DTS for v6.9
1. Marvell MMP2: Very old issue, for which I sent patch back in 2014.
Patch was never picked up and now another try to fix the same
happened, so here it goes: use proper compatible MAX8925.
2. Marvell Dove: add proper unit-addresses.
3. TI DA850: add MMC interrupts.
4. STI: minor white-space fixes.
* tag 'dt-cleanup-6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
ARM: dts: sti: minor whitespace cleanup around '='
ARM: dts: da850: add MMD SDIO interrupts
ARM: dts: marvell: dove-cubox: fix si5351 node names
arm: dts: marvell: Fix maxium->maxim typo in brownstone dts
Link: https://lore.kernel.org/r/20240218182656.32103-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Various control signals such as sfp module-absence, pci-e reset or led
gpios were missing pinctrl nodes, leaving any u-boot choices in place.
Since U-Boot is shared between multiple board variants, i.e. a388
clearfog pro / base, clearfog gtr l8 / s4, it is better to explicitly
configure functions.
Add explicit pinctrl entries for all gpios currently in use.
Additionally the loss-of-signal gpio specified is invalid, in fact los
only has a pull-up on the board but no gpio connection to the cpu.
Remove this stray reference.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Most arm board have a board-specific compatible string that allows e.g.
userspace to match specific firmware variants or apply specific
policies.
Add board-specific properties to both variants of the Clearfog GTR:
- solidrun,clearfog-gtr-l8
- solidrun,clearfog-gtr-s4
Introduction of a common parent (e.g. "solidrun,clearfog-gtr") is
omitted for brevity.
Since announcement of the two products no additional variants were added
it is assumed that there will always be just two.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Armada 388 Clearfog ("armada-388-clearfog.dts)" is a legacy filename for
the Armada 388 Clearfog Pro ("armada-388-clearfog-pro.dts").
The "Pro" suffix was only used when the smaller version, the "Base" got
released.
The two names refer to exactly the same hardware, therefore they should
share the same compatible strings.
Copy "solidrun,clearfog-pro-a1" compatible from the -pro dts and add it
to this legacy file.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fix some errors in the Marvell MV88E6xxx switch descriptions:
- The top node had no address size or cells.
- switch0@0 is not OK, should be ethernet-switch@0.
- The ports node should be named ethernet-ports
- The ethernet-ports node should have port@0 etc children, no
plural "ports" in the children.
- Ports should be named ethernet-port@0 etc
- PHYs should be named ethernet-phy@0 etc
This serves as an example of fixes needed for introducing a
schema for the bindings, but the patch can simply be applied.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fixed regulators are not in some bus and bindings do not allow a "reg"
property. Move them out of "regulators" node to top-level.
dove-cubox.dtb: regulator@1: Unevaluated properties are not allowed ('reg' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Fixed regulators are not in some bus and bindings do not allow a "reg"
property. Move them out of "regulators" node to top-level.
armada-370-dlink-dns327l.dtb: regulator@1: Unevaluated properties are not allowed ('reg' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The unit address needs to be changed to match the reg property:
arch/arm/boot/dts/marvell/armada-390-db.dts:84.10-106.4: Warning (spi_bus_reg): /soc/spi@10680/flash@1: SPI bus unit address format error, expected "0"
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
