Radxa Zero2 is a small form factor SBC based on the Amlogic A311D
chipset that ships in a number of eMMC configurations:
- Amlogic A311D (Quad A73 + Dual A53) CPU
- 4GB LPDDR4 RAM
- 32/64/128GB eMMC
- Mali G52-MP4 GPU
- HDMI 2.1 output (micro)
- BCM4345 WiFi (2.4/5GHz a/b/g/n/ac) and BT 5.0
- 1x USB 2.0 port - Type C (OTG)
- 1x USB 3.0 port - Type C (Host)
- 1x micro SD Card slot
- 40 Pin GPIO header
Signed-off-by: Yuntian Zhang <yt@radxa.com>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230127150536.3719090-2-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
ODROID-N2L is a variant SBC in small form factor and some peripherals
are removed from ODROID-N2PLUS based on S922X SoC.
- On-board ethernet is removed
- On-board RTC is removed
- USB 3.0 hub is removed, so one USB 2.0 and one USB 3.0 host ports
are available
- Huge heatsink is replaced with 40x40mm heatsink, 5V active heatsink
is recommended or a tall passive sink is optional
- 3.5mm earjack is removed
- IR remote receiver is removed
- MIPI DSI port is added new but not yet supported
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Link: https://lore.kernel.org/r/20230122-topic-odroid-n2l-upstream-initial-v2-3-8d3fea6d403d@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
This adds initial support for the Hardkernel Odroid Go Ultra.
The Odroid Go Ultra is a portable gaming device with the following
characteristics:
- Amlogic S922X SoC
- RK817 & RK818 PMICs
- 2GiB LPDDR4
- On board 16GiB eMMC
- Micro SD Card slot
- 5inch 854×480 MIPI-DSI TFT LCD
- Earphone stereo jack, 0.5Watt 8Ω Mono speaker
- Li-Polymer 3.7V/4000mAh Battery
- USB-A 2.0 Host Connector
- x16 GPIO Input Buttons
- 2x ADC Analog Joysticks
- USB-C Port for USB2 Device and Charging
The following are not yet handled:
- Battery RK818 Gauge and Charging
- Earphone stereo jack detect
- 5inch 854×480 MIPI-DSI TFT LCD
Link: https://lore.kernel.org/r/20221031-b4-odroid-go-ultra-initial-v2-2-a3df1e09b0af@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The Beelink GT1 Ultimate is based on the Amlogic S912 (Q200)
reference design with the following specifications:
- 3GB DDR3 RAM
- 32GB eMMC
- HDMI 2.1 video
- S/PDIF optical output
- 10/100/1000 Ethernet
- AP6356S Wireless (802.11 a/b/g/n, BT 4.2)
- 3x USB 2.0 ports
- IR receiver
- 1x micro SD card slot
- 1x Power LED (white)
- 1x Reset button (internal)
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220707093954.21716-2-christianshewitt@gmail.com
- add support for JetHome JetHub D1p (https://jethome.ru/d1p) is a home
automation controller with the following features:
- DIN Rail Mounting
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1/2/4GB LPDDR4
- 8/16/32GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth Realtek 8822CS or similar IEEE 802.11a/b/g/n/ac
- TI CC2652P1 Zigbee Wireless Module with up to 20dBm output power
and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Active POE
- unify device tree files for JetHub D1/D1p devices
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220811103113.3097868-2-adeep@lexina.in
The OSMC Vero 4K+ device is based on the Amlogic S905D (P230)
reference design with the following specifications:
- 2GB DDR4 RAM
- 16GB eMMC
- HDMI 2.1 video
- S/PDIF optical output
- AV output
- 10/100/1000 Ethernet
- AP6255 Wireless (802.11 a/b/g/n/ac, BT 4.2)
- 2x USB 2.0 ports (1x OTG)
- IR receiver (internal)
- IR extender port (external)
- 1x micro SD card slot
- 1x Power LED (red)
- 1x Reset button (in AV jack)
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Chad Wagner <wagnerch42@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220211105311.30320-4-christianshewitt@gmail.com
The Haochuangyi H96-Max is based on the Amlogic S905X3 reference
design with the following specs:
- 4GB DDR4 RAM
- 32/64/128GB eMMC
- HDMI 2.1 video
- S/PDIF optical output
- AV output
- 10/100/1000 Base-T Ethernet
- AP6356S Wireless (802.11 a/b/g/n/ac, BT 4.1)
- 1x USB 2.0 OTG port
- 1x USB 3.0 port
- IR receiver
- 1x micro SD card slot (internal)
- 1x Reset/Update button (in AV jack)
- 7-segment VFD
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Benoit Masson <yahoo@perenite.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220112022713.25962-10-christianshewitt@gmail.com
The CYX A95XF3-AIR is based on Amlogic S905X3 reference board
designs and ships in multiple configurations:
– 4GB DDR3 + 64GB eMMC + WiFi a/b/g/n/ac + BT + Gb Ethernet
– 4GB DDR3 + 32GB eMMC + WiFi a/b/g/n/ac + BT + Gb Ethernet
– 2GB DDR3 + 16GB eMMC + WiFi b/g/n (no BT) + 10/100 Ethernet
...
- HDMI 2.1 video
- S/PDIF optical output
- AV output
- 1x USB 2.0 OTG port
- 1x USB 3.0 port
- IR receiver
- 1x micro SD card slot (internal)
- 1x Reset/Update button (in AV jack)
- 7-segment VFD
- Multicolour case LED 'arc'
The device-tree with -gbit suffix supports models with Gigabit
Ethernet, and the device-tree with no suffix supports models
with 10/100 Ethernet.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220112022713.25962-7-christianshewitt@gmail.com
The Amediatek X96-AIR is based on Amlogic S905X3 reference board
designs and ships in multiple configurations:
– 4GB DDR3 + 64GB eMMC + WiFi a/b/g/n/ac + BT + Gb Ethernet
– 4GB DDR3 + 32GB eMMC + WiFi a/b/g/n/ac + BT + Gb Ethernet
– 4GB DDR3 + 32GB eMMC + WiFi b/g/n (no BT) + 10/100 Ethernet
– 2GB DDR3 + 16GB eMMC + WiFi b/g/n (no BT) + 10/100 Ethernet
...
- HDMI 2.1 video
- S/PDIF optical output
- AV output
- 2x USB 2.0 inc. OTG port
- 1x USB 3.0 port
- IR receiver
- 1x micro SD card slot (internal)
- 1x Reset/Update button (in AV jack)
- 7-segment VFD
The device-tree with -gbit suffix supports models with Gigabit
Ethernet, and the device-tree with no suffix supports models
with 10/100 Ethernet.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # X96-Air with Gbit PHY
Tested-by: Piotr Oniszczuk <piotr.oniszczuk@gmail.com> # X96-Air with 10/100 Eth
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220112022713.25962-4-christianshewitt@gmail.com
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation
controller with the following features:
- DIN Rail Mounting
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB LPDDR4
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac,
Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added missing newline in DT and removed changelog from commit msg]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210915085715.1134940-5-adeep@lexina.in
JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation
controller with the following features:
- square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB LPDDR4
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power
and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210915085715.1134940-4-adeep@lexina.in
Radxa Zero is a small form factor SBC based on the Amlogic S905Y2
chipset that ships in a number of RAM/eMMC configurations:
Boards with 512MB/1GB LPDDR4 RAM have no eMMC storage and BCM43436
wireless (2.4GHz b/g/n) while 2GB/4GB boards have 8/16/32/64/128GB
eMMC storage and BCM4345 wireless (2.4/5GHz a/b/g/n/ac).
- Amlogic S905Y2 quad-core Cortex-A53
- Mali G31-MP2 GPU
- HDMI 2.1 output (micro)
- 1x USB 2.0 port - Type C (OTG)
- 1x USB 3.0 port - Type C (Host)
- 1x micro SD Card slot
- 40 Pin GPIO header
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210909102154.22710-3-christianshewitt@gmail.com
The WeTek Core2 is a commercial device based on the Amlogic Q200 reference
design but with the following differences:
- 3GB RAM, 32GB eMMC
- Blue and Red LEDs used to signal on/off status
- uart_AO can be accessed after opening the case; soldering required
- USB OTG is not accessible (inside the case)
- Realtek RTL8152 Ethernet (internal USB connection)
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20200719021421.7959-3-christianshewitt@gmail.com
The Shenzen AZW (Beelink) GT-King Pro is based on the Amlogic W400
reference board with an S922X chip.
- 4GB LPDDR4 RAM
- 64GB eMMC storage
- 10/100/1000 Base-T Ethernet
- AP6356S Wireless (802.11 a/b/g/n/ac, BT 4.1)
- HDMI 2.1 video
- Analogue audio output
- 1x RS232 port
- 2x USB 2.0 port
- 2x USB 3.0 ports
- IR receiver
- 1x micro SD card slot
- 1x Power on/off button
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200520014329.12469-6-christianshewitt@gmail.com
The Smartlabs SML-5442TW is based on the Amlogic P231 reference design
but with the following differences:
- The Yellow and Blue LEDs are available but disabled
- The Red and Green LEDs are used to signal off/on status
- uart_AO can be accessed after opening the case; soldered pins exist
- QCA9377 instead of the usual Ampak/Broadcom module
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200510124129.31575-4-christianshewitt@gmail.com
Add support for the the amlogic libretech-pc platform, aka tartiflette.
There is 2 variants of the platform, one with the s905d, the other with
the s912.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds support for the Videostrong KII Pro tv box which is
based on the gxbb-p201 reference design
Device specifications:
- SOC: Amlogic S905
- RAM: 2GB DDR3
- Storage: 16GB
- Connectivity:
- 10/100M Ethernet (IC Plus IP101GR)
- 802.11 b/g/n/ac Wi-Fi (Ampak AP6335 BT/WIFI combo)
- Bluetooth 4.0 (Ampak AP6335 BT/WIFI combo)
- Video out: HDMI 2.0 up to 4K @ 60Hz, and 3.5mm AV (composite video) jack
- Audio out: HDMI, AV (stereo audio) and optical S/PDIF
- Tuner: AVL6862 DVB-C/T/T2 + DVB-S/S2 demod and Rafael Micro R848 tuner
- Ports:
- x1 micro SD card slot up to 32GB
- 4x USB 2.0 host ports
- Misc:
- Power button and LED, IR receiver
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Ugoos AM6 is based on the Amlogic W400 (G12B) reference design using the
S922X chipset. Hardware specifications:
- 2GB LPDDR4 RAM
- 16GB eMMC storage
- 10/100/1000 Base-T Ethernet using External RGMII PHY
- 802.11 a/b/g/b/ac + BT 5.0 sdio wireless (Ampak 6398S)
- HDMI 2.0 (4k@60p) video
- Composite video + 2-channel audio output on 3.5mm jack
- S/PDIF audio output
- Aux input
- 1x USB 3.0
- 3x USB 2.0
- 1x micro SD card slot
The device-tree is largely based on meson-g12b-odroid-n2 but with audio
and USB config copied from meson-g12a-x96-max.
Tested-by: Oleg Ivanov <balbes-150@yandex.ru>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the Amlogic SM1 based Khadas VIM3L, sharing all the same features
as the G12B based VIM3, but:
- a different DVFS support since only a single cluster is available
- audio is still not available on SM1
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add support for the Amlogic SM1 Based SEI610 board.
The SM1 SoC is a derivative of the G12A SoC Family with :
- Cortex-A55 core instead of A53
- more power domains, including USB & PCIe
- a neural network co-processor (NNA)
- a CSI input and image processor
- some changes in the audio complex, thus not yet enabled
The SEI610 board is a derivative of the SEI510 board with :
- removed ADC based touch button, replaced with 3x GPIO buttons
- physical switch disabling on-board MICs
- USB-C port for USB 2.0 OTG
- On-board FTDI USB2SERIAL port for Linux console
Audio, Display and USB support will be added later when support of the
corresponding power domains will be added, for now they are kept disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[khilman: fix minor typo regultor -> regulator]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Khadas VIM3 uses the Amlogic S922X or A311S SoC, both based on the
Amlogic G12B SoC family, on a board with the same form factor as the
VIM/VIM2 models. It ships in two variants; basic and
pro which differ in RAM and eMMC size:
- 2GB (basic) or 4GB (pro) LPDDR4 RAM
- 16GB (basic) or 32GB (pro) eMMC 5.1 storage
- 16MB SPI flash
- 10/100/1000 Base-T Ethernet
- AP6398S Wireless (802.11 a/b/g/n/ac, BT5.0)
- HDMI 2.1 video
- 1x USB 2.0 + 1x USB 3.0 ports
- 1x USB-C (power) with USB 2.0 OTG
- 3x LED's (1x red, 1x blue, 1x white)
- 3x buttons (power, function, reset)
- IR receiver
- M2 socket with PCIe, USB, ADC & I2C
- 40pin GPIO Header
- 1x micro SD card slot
A common meson-g12b-khadas-vim3.dtsi is added to support both S922X and
A311D SoCs supported by two variants of the board.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds basic support for :
- Amlogic G12B, which is very similar to G12A
- The HardKernel Odroid-N2 based on the S922X SoC
The Amlogic G12B SoC is very similar with the G12A SoC, sharing
most of the features and architecture, but with these differences :
- The first CPU cluster only has 2xCortex-A53 instead of 4
- G12B has a second cluster of 4xCortex-A73
- Both cluster can achieve 2GHz instead of 1,8GHz for G12A
- CPU Clock architecture is difference, thus needing a different
compatible to handle this slight difference
- Supports a MIPI CSI input
- Embeds a Mali-G52 instead of a Mali-G31, but integration is the same
Actual support is done in the same way as for the GXM support, including
the G12A dtsi and redefining the CPU clusters.
Unlike GXM, the first cluster is different, thus needing to remove
the last 2 cpu nodes of the first cluster.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
[khilman: add vin-supply for vcc_v5 as suggested by Anand Moon]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The SEI Robotics SEI510 Board is based on the Amlogic G12A S905X2
and has the following features :
- Amlogic G12A S905X2 SoC
- 10/100 Ethernet
- USB2 + USB3 ports
- Micro SDCard Port
- Audio + CVBS AV Jack port
- HDMI 2.1 + CEC Port
- ADC Touch Button
- Far-Field Microphone Array + Mono HP
- IR Sensor
- IR Emmiter LED Array
- RGB Led
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: sorted Makefile entry alphabetcially]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds support for the Phicomm N1. This device based on P230 reference design.
And this box doesn't have cvbs, so disable related section in device tree.
Signed-off-by: He Yangxuan <yangxuan8282@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Try to add basic DT support for the Amlogic's Meson-G12A S905D2 SoC,
which describe components as follows: Reserve Memory, CPU, GIC, IRQ,
Timer, UART. It's capable of booting up into the serial console.
Signed-off-by: Jianxin Pan <jianxin.pan@amlogic.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
