Unit name is supposed to be a number, using a macro with hex value is
not recommended, so add the value in unit name.
arch/arm64/boot/dts/qcom/pm8998.dtsi:81.18-84.6: Warning (unit_address_format): /soc/spmi@c440000/pmic@0/adc@3100/adc-chan@0x06: unit name should not have leading "0x"
arch/arm64/boot/dts/qcom/pm8998.dtsi:81.18-84.6: Warning (unit_address_format): /soc/spmi@c440000/pmic@0/adc@3100/adc-chan@0x06: unit name should not have leading 0s
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The temperature information from the temp-alarm block itself is very
coarse ("temperature is above/below trip points"). Provide the driver
with the die temperature channel of the ADC on the PMIC for more precise
readings.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <agross@kernel.org>
This adds the gpio-ranges property so that the GPIO pins are initialized
by the GPIO framework and not pinctrl. This fixes a circular dependency
between these two frameworks so GPIO hogging can be used on this board.
This was not tested on this particular hardware, however this same
change was tested on qcom-pm8941 using a LG Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add interrupt controller properties now that spmi-gpio is a proper
hierarchical IRQ chip. The interrupts property is no longer needed so
remove it.
This change was not tested on any hardware but the same change was
tested on qcom-pm8941.dtsi using a LG Nexus 5 (hammerhead) phone with
no issues.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The thermal zone uses spmi-temp-alarm as sensor, the trip points
correspond to the PMIC thermal stages 1 and 2. The critical trip
point at 125°C disables the partial PMIC shutdown at stage 2.
Without an IIO input the sensor only reports a limited number of
temperatures:
- 37°C for temperatures below 105°C
- 107°C for temperatures >= 105°C and < 125°C
- 127°C for temperatures >= 125°C
(the numbers correspond to a stage 1 threshold of 105°C)
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the spmi-temp-alarm node to pm8998 based on the examples in the
bindings.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the adc node to pm8998 based on the examples in the
bindings. It also fixes the order of the included headers.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
