On non-QUSB2 targets (like the ones that use femto phys, M31 phy, eusb2
phy), many of the QCOM DTs are missing the IRQ for either hs_phy_irq or
pwr_event. In one case, the hs_phy_irq was incorrectly defined with the
latter's IRQ number. Since the DT must describe the hw whether or not
the driver uses these interrupts, fix and add the missing entries in order
to describe the HW completely and accurately.
Also modify order of interrupts in accordance to bindings update.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Link: https://lore.kernel.org/r/20240125185921.5062-3-quic_kriskura@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Pull ARM devicetree updates from Arnd Bergmann:
"These are the devicetree updates for Arm and RISC-V based SoCs, mainly
from Qualcomm, NXP/Freescale, Aspeed, TI, Rockchips, Samsung, ST and
Starfive.
Only a few new SoC got added:
- TI AM62P5, a variant of the existing Sitara AM62x family
- Intel Agilex5, an FPGFA platform that includes an Cortex-A76/A55
SoC.
- Qualcomm ipq5018 is used in wireless access points
- Qualcomm SM4450 (Snapdragon 4 Gen 2) is a new low-end mobile phone
platform.
In total, 29 machines get added, which is low because of the summer
break. These cover SoCs from Aspeed, Broadcom, NXP, Samsung, ST,
Allwinner, Amlogic, Intel, Qualcomm, Rockchip, TI and T-Head. Most of
these are development and reference boards.
Despite not adding a lot of new machines, there are over 700 patches
in total, most of which are cleanups and minor fixes"
* tag 'soc-dt-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (735 commits)
arm64: dts: use capital "OR" for multiple licenses in SPDX
ARM: dts: use capital "OR" for multiple licenses in SPDX
arm64: dts: qcom: sdm845-db845c: Mark cont splash memory region as reserved
ARM: dts: qcom: apq8064: add support to gsbi4 uart
riscv: dts: change TH1520 files to dual license
riscv: dts: thead: add BeagleV Ahead board device tree
dt-bindings: riscv: Add BeagleV Ahead board compatibles
ARM: dts: stm32: add SCMI PMIC regulators on stm32mp135f-dk board
ARM: dts: stm32: STM32MP13x SoC exposes SCMI regulators
dt-bindings: rcc: stm32: add STM32MP13 SCMI regulators IDs
ARM: dts: stm32: support display on stm32f746-disco board
ARM: dts: stm32: rename mmc_vcard to vcc-3v3 on stm32f746-disco
ARM: dts: stm32: add pin map for LTDC on stm32f7
ARM: dts: stm32: add ltdc support on stm32f746 MCU
arm64: dts: qcom: sm6350: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sa8775p: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sc8280xp: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Add PDC
riscv: dts: starfive: fix jh7110 qspi sort order
...
Add the CPU and LLC BWMONs (skip the NPU ones for now) on sm8250.
LPDDR4X levels are skipped, as LPDDR5 seems more popular with SM8250 and
voting for inexistent levels doesn't uptick the bus frequency, which
results in no increased bandwidth, which results in bwmon deciding we
shouldn't go higher.. you see the point!
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230711-topic-sm638250_bwmon-v1-3-bd4bb96b0673@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
sm8250 faces the same problem with its Energy Model as sdm845. The energy
cost of LITTLE cores is reported to be higher than medium or big cores
EM computes the energy with formula:
energy = OPP's cost / maximum cpu capacity * utilization
On v6.4-rc6 we have:
max capacity of CPU0 = 284
capacity of CPU0's OPP(1612800 Hz) = 253
cost of CPU0's OPP(1612800 Hz) = 191704
max capacity of CPU4 = 871
capacity of CPU4's OPP(710400 Hz) = 255
cost of CPU4's OPP(710400 Hz) = 343217
Both OPPs have almost the same compute capacity but the estimated energy
per unit of utilization will be estimated to:
energy CPU0 = 191704 / 284 * 1 = 675
energy CPU4 = 343217 / 871 * 1 = 394
EM estimates that little CPU0 will consume 71% more than medium CPU4 for
the same compute capacity. According to [1], little consumes 25% less than
medium core for Coremark benchmark at those OPPs for the same duration.
Set the dynamic-power-coefficient of CPU0-3 to 105 to fix the energy model
for little CPUs.
[1] https://github.com/kdrag0n/freqbench/tree/master/results/sm8250/k30s
Fixes: 6aabed5526 ("arm64: dts: qcom: sm8250: Add CPU capacities and energy model")
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Link: https://lore.kernel.org/r/20230615154852.130076-1-vincent.guittot@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Since commit 6c84bbd103 ("dt-bindings: arm-smmu: Add generic
qcom,smmu-500 bindings") the SMMU is supposed to use qcom,smmu-500
compatible fallback:
['qcom,sm8250-smmu-500', 'qcom,adreno-smmu', 'qcom,smmu-500', 'arm,mmu-500'] is too long
'qcom,sm8250-smmu-500' is not one of ['qcom,msm8996-smmu-v2', 'qcom,msm8998-smmu-v2', 'qcom,sdm630-smmu-v2']
'qcom,sm8250-smmu-500' is not one of ['qcom,msm8996-smmu-v2', 'qcom,sc7180-smmu-v2', 'qcom,sdm630-smmu-v2', 'qcom,sdm845-smmu-v2'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230416123730.300863-4-krzysztof.kozlowski@linaro.org
Currently, most of the Qualcomm SoCs specify both "iommus" and "iommu-map"
properties for the PCIe nodes. First one passes the SMR mask to the iommu
driver and the latter specifies the SID for each PCIe device.
But with "iommus" property, the PCIe controller will be added to the
iommu group along with the devices. This makes no sense because the
controller will not initiate any DMA transaction on its own. And moreover,
it is not strictly required to pass the SMR mask to the iommu driver. If
the "iommus" property is not present, then the default mask of "0" would be
used which should work for all PCIe devices.
On the other side, if the SMR mask specified doesn't match the one expected
by the hypervisor, then all the PCIe transactions will end up triggering
"Unidentified Stream Fault" by the SMMU.
So to get rid of these hassles and also prohibit PCIe controllers from
adding to the iommu group, let's remove the "iommus" property from PCIe
nodes.
Reported-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-arm-msm/20230227195535.GA749409-robh@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308075648.134119-1-manivannan.sadhasivam@linaro.org
There is only one output port, thus out-ports should not have
'address/size-cells' and unit addresses. 'reg-names' are also not
allowed by bindings.
qrb5165-rb5.dtb: funnel@6042000: out-ports: '#address-cells', '#size-cells', 'port@0' do not match any of the regexes: 'pinctrl-[0-9]+'
qrb5165-rb5.dtb: funnel@6b04000: Unevaluated properties are not allowed ('reg-names' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308125906.236885-2-krzysztof.kozlowski@linaro.org
Pull clk updates from Stephen Boyd:
"We have one small patch to the clk core this time around. It fixes a
corner case with the CLK_OPS_PARENT_ENABLE flag combined with
clk_core_is_enabled() where it hangs the system. We'll simply assume
the clk is disabled if the parent is disabled and the flag is set.
Trying to turn on the parent to check the enable state of the clk runs
into system hangs at boot. We let this bake in -next for a couple
weeks to make sure there aren't any more issues because the last
attempt to fix this ran into hangs and had to be reverted.
Note: There were some more patches to the core framework around
sync_state and disabling unused clks, but I asked for that to be
reverted from the qcom PR because it isn't ready and we're still
discussing the best solution on the list.
Outside of the core clk framework, we have the usual collection of clk
driver updates and support for new SoCs (which seems to never stop).
The dirstat is dominated by Qualcomm because they added support for
quite a few SoCs this time around and also migrated quite a few of
their drivers to clk_parent_data. The other big diff is in the
Mediatek clk drivers that saw a significant rework this cycle to
similarly modernize the code, and we'll see that work continue in the
next cycle as well. Nothing really jumps out as scary here, except
that the significant churn in parent data descriptions can have typos
that go unnoticed. More details below.
Core:
- Honor CLK_OPS_PARENT_ENABLE in clk_core_is_enabled()
New Drivers:
- Add a new clk-gpr-mux clock type and use it on i.MX6Q to add ENET
ref clocks
- Support for Mediatek MT7891 SoC clks
- Support for many Qualcomm clk controllers:
- QDU1000/QRU1000 global clock controller
- SA8775P global clock controller
- SM8550 TCSR and display clock controller
- SM6350 clock controller
- MSM8996 CBF and APCS clock controllers
Updates:
- Various cleanups and improvements to Mediatek clk drivers to reduce
code size and modernize the drivers
- Support for Versa 5P49V60 clks
- Disable R-Car H3 ES1.*, as it was only available to an internal
development group and needed a lot of quirks and workarounds
- Add PWM, Compare-Match Timer (TIM), USB, SDHI, and eMMC clocks and
resets on Renesas RZ/V2M
- Add display clocks on Renesas R-Car V4H
- Add Camera Receiving Unit (CRU) clocks and resets on Renesas RZ/G2L
- Free the imx_uart_clocks even if imx_register_uart_clocks returns
early
- Get the stdout clocks count from device tree on i.MX
- Drop the clock count argument from imx_register_uart_clocks()
- Keep the uart clocks on i.MX93 for when earlycon is used
- Fix SPDX comment in i.MX6SLL clocks bindings header
- Drop some unnecessary spaces from i.MX8ULP clocks bindings header
- Add imx_obtain_fixed_of_clock() for allowing to add a clock that is
not configured via devicetree
- Fix the ENET1 gate configuration for i.MX6UL according to the
reference manual
- Add ENET refclock mux support for i.MX6UL
- Add support for USB host/device configuration on Renesas RZ/N1
- Add PLL2 programming support, and CAN-FD clocks on Renesas R-Car
V4H
- Add D1 CAN bus gates and resets for Allwinner
- Mark D1 CPUX clock as critical on Allwinner
- Reuse D1 driver for Allwinner R528/T113
- Cleanup sunxi-ng Kconfig
- Fix sunxi-ng kernel-doc issues
- Model Allwinner H3/H5 DRAM clock as fixed clock
- Use .determine_rate() instead of .round_rate() for the dualdiv,
mpll, sclk-div and cpu-dyn-div amlogic clock drivers
- DDR clocks were marked as critical in the proper clock driver for
each AT91 SoC such that drivers/memory/atmel-sdramc.c to be deleted
in the next releases as it only does clock enablement
- Patch to avoid compiling dt-compat.o for all AT91 SoCs as only some
of them may use it
- Support synchronous power_off requests in the qcom GDSC driver for
proper GPU power collapse
- Drop test clocks from various Qualcomm clk drivers
- Update parent references to use clk_parent_data/clk_hw in various
Qualcomm clk drivers
- Fixes for the Qualcomm MSM8996 CPU clock controller
- Transition Qualcomm MSM8974 GCC off the externally defined
sleep_clk
- Add GDSCs in the global clock controller for Qualcomm QCS404
- The SDCC core clocks on Qualcomm SM6115 are moved to floor_ops
- Programming of clk_dis_wait for GPU CX GDSC on Qualcomm SC7180 and
SDM845 are moved to use the recently introduced properties in the
GDSC struct
- Qualcomm's RPMh clock driver gains SM8550 and SA8775P clocks, and
the IPA clock is added on a variety of platforms
- De-duplicate identical clks in Qualcomm SMD RPM clk driver
- Add a few missing clocks across msm8998, msm8992, msm8916, qcs404
to Qualcomm SDM RPM clk driver
- Various Qualcomm clk drivers use devm_pm_runtime_enable() to
simplify"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (228 commits)
clk: qcom: apcs-msm8986: Include bitfield.h for FIELD_PREP
clk: qcom: Revert sync_state based clk_disable_unused
clk: imx: pll14xx: fix recalc_rate for negative kdiv
clk: rs9: Drop unused pin_xin field
MAINTAINERS: clk: imx: Add Peng Fan as reviewer
clk: sprd: Add dependency for SPRD_UMS512_CLK
clk: ralink: fix 'mt7621_gate_is_enabled()' function
clk: mediatek: clk-mtk: Remove unneeded semicolon
dt-bindings: clock: remove stih416 bindings
dt-bindings: clock: add loongson-2 clock
dt-bindings: clock: add loongson-2 clock include file
clk: imx: fix compile testing imxrt1050
clk: Honor CLK_OPS_PARENT_ENABLE in clk_core_is_enabled()
clk: imx: set imx_clk_gpr_mux_ops storage-class-specifier to static
clk: renesas: rcar-gen3: Disable R-Car H3 ES1.*
dt-bindings: clock: Merge qcom,gpucc-sm8350 into qcom,gpucc.yaml
clk: qcom: gpucc-sdm845: fix clk_dis_wait being programmed for CX GDSC
clk: qcom: gpucc-sc7180: fix clk_dis_wait being programmed for CX GDSC
dt-bindings: clock: qcom,sa8775p-gcc: add the power-domains property
clk: qcom: cpu-8996: add missing cputype include
...
