The generic platform driver pcie-designware-plat.c doesn't work for
UniPhier PCIe host controller, because the controller has some
necessary initialization sequence for the controller-specific logic.
Currently the controller doesn't use "snps,dw-pcie" compatible,
so this is no longer needed. Remove the compatible string from the
pcie node.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-10-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
According to gpio-hog schema, should add the suffix "-hog" to the node
names including gpio-hog to fix the following warning.
uniphier-ld11-ref.dtb: gpio@55000000: 'xirq0' does not match any of the regexes: '^.+-hog(-[0-9+)?$', 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/gpio/socionext,uniphier-gpio.yaml
This applies to the devicetre for LD11, LD20 and PXs3 SoCs.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/20220913042321.4817-5-hayashi.kunihiko@socionext.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
UniPhier LD20 and PXs3 boards have RTL8211E ethernet phy, and the phy have
the RX/TX delays of RGMII interface using pull-ups on the RXDLY and TXDLY
pins.
After the commit bbc4d71d63 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the delays are working correctly, however, "rgmii" means
no delay and the phy doesn't work. So need to set the phy-mode to
"rgmii-id" to show that RX/TX delays are enabled.
Fixes: c73730ee4c ("arm64: dts: uniphier: add AVE ethernet node")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds missing clock-names and reset-names to pcie-phy node according to
Documentation/devicetree/bindings/phy/socionext,uniphier-pcie.yaml.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This renames the node name "ethphy" to "ethernet-phy" according to
Documentation/devicetree/bindings/net/mdio.yaml.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit e69f5dc623 ("dt-bindings: serial: Convert 8250 to
json-schema"), the schema for "ns16550a" is checked.
Since then, 'make ARCH=arm64 dtbs_check' is so noisy because the
required property 'interrupts' is missing.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add the device tree for Akebi96. Akebi96 is a 96boards certified
development board based on UniPhir LD20.
( https://www.96boards.org/product/akebi96/ )
This board has;
- MAX3421 USB-SPI chip on SPI port3 (for USB gadget port)
- Simple frame buffer with 1080p fixed resolution.
- I2S port which is connected to aout1b instead of aout1.
- 3 serial ports, only serial3 has CTS/RTS.
- No NAND, only eMMC on the board.
- OP-TEE installed firmware.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Documentation/devicetree/bindings/spi/spi-uniphier.txt requires
#address-cells and #size-cells, but they are missing in actual DT files.
Also, 'make ARCH=arm64 dtbs_check' is really noisy.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The RGMII PHY implemented in PXs3 ref board needs to change
drive-strength properties of the Ethernet Tx pins to stabilize the PHY.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add 'aliases' properties for ethernet device.
U-Boot performs a fix-up of the MAC address and will overwrite the values
from the Linux devicetree for aliased ethernet device. The MAC address can
be inherited from U-Boot by adding aliases of ethernet devices.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently common clock and reset IDs were used, however, each clock and
reset ID should be used for each channel.
Fixes: 925c5c32f3 ("arm64: dts: uniphier: add SPI node for LD20, LD11 and PXs3")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add nodes of thermal monitor and thermal zone for UniPhier PXs3 SoC.
The thermal monitor node is included in sysctrl. This patch gives the
default value for PXs3 in the same way as LD20.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
PXs3 reference board has 2 spi connectors. This enables spi0 and spi1,
and adds aliases properties for each spi to determine device name
assignments.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow the standard nodename pattern "^nand-controller(@.*)?" defined
in Documentation/devicetree/bindings/mtd/nand-controller.yaml
Otherwise, after the dt-binding is converted to json-schema,
'make ARCH=arm64 dtbs_check' will show warnings like this:
nand@68000000: $nodename:0: 'nand@68000000' does not match '^nand-controller(@.*)?'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow the standard nodename pattern "^interrupt-controller(@[0-9a-f,]+)*$"
defined in schemas/interrupt-controller.yaml of dt-schema.
Otherwise, after the dt-binding is converted to json-schema,
'make ARCH=arm64 dtbs_check' will show warnings like this:
aidet@5fc20000: $nodename:0: 'aidet@5fc20000' does not match '^interrupt-controller(@[0-9a-f,]+)*$'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow the standard nodename pattern "^mmc(@.*)?$" defined in
Documentation/devicetree/bindings/mmc/mmc-controller.yaml
Otherwise, after the dt-binding is converted to json-schema,
'make ARCH=arm64 dtbs_check' will show warnings like this:
sdhc@5a000000: $nodename:0: 'sdhc@5a000000' does not match '^mmc(@.*)?$'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Denali NAND controller IP has separate reset control for the
controller core and registers.
Add the reset-names, and one more phandle accordingly. This is the
approved DT-binding.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The memory regions specified by /memreserve/ are passed to
early_init_dt_reserve_memory_arch() with nomap=false, so it is
not suitable for reserving memory for Trusted Firmware-A etc.
Use the more robust /reserved-memory node with the no-map property
to prevent the kernel from mapping it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With commit d8e8fd0ebf ("mtd: rawnand: denali: decouple controller
and NAND chips"), the Denali NAND controller driver migrated to the
new controller/chip representation.
Update DT for it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
UniPhier ARM64 SoC DT updates for v5.1
- Add PCI Express controller nodes
* tag 'uniphier-dt64-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: sort labels in the same order as in dtsi
arm64: dts: uniphier: Add PCIe host controller and PHY nodes
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Sort the labels in the same order as in the corresponding dtsi file,
in other words, the order of reg address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add USB3 controller nodes including usb-core, resets, regulator, ss-phy
and hs-phy. This supports for LD20, PXs3 and the boards. This includes
additional efuse nodes for obtaining PHY trimming values.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add SD controller nodes for LD20 and PXs3.
LD20 does not support the UHS mode, while PXs3 supports it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Catch up with the new binding of the Denali IP where three clocks,
"nand", "nand_x", "ecc" are required.
For UniPhier SoCs, the "nand_x" and "ecc" are tied up because they
are both 200MHz.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
