Add default #address-cells and #size-cells properties to the
usb node, which should be suitable for hubs and devices without
explicitly declared interface nodes, as:
"#address-cells":
description: should be 1 for hub nodes with device nodes,
should be 2 for device nodes with interface nodes.
enum: [1, 2]
"#size-cells":
const: 0
-- from Documentation/devicetree/bindings/usb/usb-device.yaml
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Each item of the resets property should define a reset. Split the item with
two resets on the ethernet node into two separate items.
Sort the items of the clocks property to the same line as a trivial change.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
To allow to access system controller registers from watchdog driver code
add a phandle in the watchdog 'wdt' node. This avoid using arch dependent
operations in driver code.
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Watchdog nodes must use 'watchdog' for node name. When a 'make dtbs_check'
is performed the following warning appears:
wdt@100: $nodename:0: 'wdt@100' does not match '^watchdog(@.*|-[0-9a-f])?$'
Fix this warning up properly renaming the node into 'watchdog'.
Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
On MT7621AT, MT7621DAT, and MT7621ST SoCs, port 5 of the MT7530 switch is
connected to the second MAC of the SoC as a CPU port. Add the port and set
up the second MAC on the bindings. Revert PHY muxing on GB-PC1.
There's an external PHY connected to the second MAC of the SoC on GB-PC2,
therefore, disable port@5 for this device.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
In the case of muxing phy0 of the MT7530 switch, the switch and the phy
will have the same address on the mdio bus, 0. This causes the ethernet
driver to fail since devices on the mdio bus cannot share an address.
Any address can be used for the switch, therefore, change the switch
address to 0x1f.
Suggested-by: Sungbo Eo <mans0n@gorani.run>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change phy-mode of gmac1 to rgmii on mt7621.dtsi. Same code path is
followed for delayed rgmii and rgmii phy-mode on mtk_eth_soc.c.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt-parent property is inherited from the ethernet node as it's a
parent node of the switch node. Therefore, remove the unnecessary
interrupt-parent property from the switch node.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the dtc warnings below.
uartlite@c00: $nodename:0: 'uartlite@c00' does not match '^serial(@.*)?$'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/serial/8250.yaml
uartlite@c00: Unevaluated properties are not allowed ('clock-names' was unexpected)
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/serial/8250.yaml
sdhci@1e130000: $nodename:0: 'sdhci@1e130000' does not match '^mmc(@.*)?$'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/mmc/mtk-sd.yaml
xhci@1e1c0000: $nodename:0: 'xhci@1e1c0000' does not match '^usb(@.*)?'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
xhci@1e1c0000: compatible: ['mediatek,mt8173-xhci'] is too short
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml
switch0@0: $nodename:0: 'switch0@0' does not match '^(ethernet-)?switch(@.*)?$'
From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml
port@1: status:0: 'off' is not one of ['okay', 'disabled', 'reserved']
From schema: /home/arinc9/.local/lib/python3.10/site-packages/dtschema/schemas/dt-core.yaml
port@2: status:0: 'off' is not one of ['okay', 'disabled', 'reserved']
From schema: /home/arinc9/.local/lib/python3.10/site-packages/dtschema/schemas/dt-core.yaml
port@3: status:0: 'off' is not one of ['okay', 'disabled', 'reserved']
From schema: /home/arinc9/.local/lib/python3.10/site-packages/dtschema/schemas/dt-core.yaml
- Change "memc: syscon@5000" to "memc: memory-controller@5000".
- Change "uartlite: uartlite@c00" to "serial0: serial@c00" and remove the
aliases node.
- Remove "clock-names" from the serial0 node. The property doesn't exist on
the 8250.yaml schema.
- Change "sdhci: sdhci@1e130000" to "mmc: mmc@1e130000".
- Change "xhci: xhci@1e1c0000" to "usb: usb@1e1c0000".
- Add "mediatek,mtk-xhci" as the second compatible string on the usb node.
- Change "switch0: switch0@0" to "switch0: switch@0"
- Change "off" to "disabled" for disabled nodes.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MIPS updates from Thomas Bogendoerfer:
"Cleanups and fixes"
* tag 'mips_5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (38 commits)
MIPS: RALINK: Define pci_remap_iospace under CONFIG_PCI_DRIVERS_GENERIC
MIPS: Use memblock_add_node() in early_parse_mem() under CONFIG_NUMA
MIPS: Return -EINVAL if mem parameter is empty in early_parse_mem()
MIPS: Kconfig: Fix indentation and add endif comment
MIPS: bmips: Fix compiler warning observed on W=1 build
MIPS: Rewrite `csum_tcpudp_nofold' in plain C
mips: setup: use strscpy to replace strlcpy
MIPS: Octeon: add SNIC10E board
MIPS: Ingenic: Refresh defconfig for CU1000-Neo and CU1830-Neo.
MIPS: Ingenic: Refresh device tree for Ingenic SoCs and boards.
MIPS: Ingenic: Add PWM nodes for X1830.
MIPS: Octeon: fix typo in comment
MIPS: loongson32: Kconfig: Remove extra space
MIPS: Sibyte: remove unnecessary return variable
MIPS: Use NOKPROBE_SYMBOL() instead of __kprobes annotation
selftests/ftrace: Save kprobe_events to test log
MIPS: tools: no need to initialise statics to 0
MIPS: Loongson: Use hwmon_device_register_with_groups() to register hwmon
MIPS: VR41xx: Drop redundant spinlock initialization
MIPS: smp: optimization for flush_tlb_mm when exiting
...
