Convert the driver to use OF match data for providing the Alpha PLL config
per compatible.
This is required for IPQ8074 support since it uses a different Alpha PLL
config.
While we are here rename "ipq_pll_config" to "ipq6018_pll_config" to make
it clear that it is for IPQ6018 only.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-5-robimarko@gmail.com
While working on IPQ8074 APSS driver it was discovered that IPQ6018 and
IPQ8074 use almost the same PLL and APSS clocks, however APSS driver is
currently broken.
More precisely apcs_alias0_clk_src is broken, it was added as regmap_mux
clock.
However after debugging why it was always stuck at 800Mhz, it was figured
out that its not regmap_mux compatible at all.
It is a simple mux but it uses RCG2 register layout and control bits, so
utilize the new clk_rcg2_mux_closest_ops to correctly drive it while not
having to provide a dummy frequency table.
While we are here, use ARRAY_SIZE for number of parents.
Tested on IPQ6018-CP01-C1 reference board and multiple IPQ8074 boards.
Fixes: 5e77b4ef1b ("clk: qcom: Add ipq6018 apss clock controller")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-2-robimarko@gmail.com
An RCG may act as a mux that switch between 2 parents.
This is the case on IPQ6018 and IPQ8074 where the APCS core clk that feeds
the CPU cluster clock just switches between XO and the PLL that feeds it.
Add the required ops to add support for this special configuration and use
the generic mux function to determine the rate.
This way we dont have to keep a essentially dummy frequency table to use
RCG2 as a mux.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220818220628.339366-1-robimarko@gmail.com
Replace parent_names in PLLs, secondary muxes and primary muxes with
parent_data. For primary muxes there were never any *cl_pll_acd clocks,
so instead of adding them, put the primary PLLs in both PLL_INDEX and
ACD_INDEX, then make sure ACD_INDEX is always picked over PLL_INDEX when
setting parent since we always want ACD when using the primary PLLs.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
[DB: switch to parent_hws for pmux clocks]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220714100351.1834711-2-dmitry.baryshkov@linaro.org
The gfx3d clock is hand-crafting its own clk_rate_request in
clk_gfx3d_determine_rate to pass to the parent of that clock.
However, since the clk_rate_request is zero'd at creation, it will have
a max_rate of 0 which will break any code depending on the clock
boundaries.
That includes the recent commit 948fb0969e ("clk: Always clamp the
rounded rate") which will clamp the rate given to clk_round_rate() to
the current clock boundaries.
For the gfx3d clock, it means that since both the min_rate and max_rate
fields are set at zero, clk_round_rate() now always return 0.
Let's initialize the min_rate and max_rate fields properly for that
clock.
Fixes: 948fb0969e ("clk: Always clamp the rounded rate")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220816112530.1837489-25-maxime@cerno.tech
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The USB PHY on MSM8909 works with the driver used on MSM8916
(phy-qcom-usb-hs.c). When turning the PHY on/off it is first reset
using the standard reset controller API. On MSM8916 the reset is
provided by the USB driver (ci_hdrc_msm_por_reset() in ci_hdrc_msm.c).
While this seems to work on MSM8909 as well, the Qualcomm Linux sources
suggest that the PHY should be reset using the GCC_USB2_HS_PHY_ONLY_BCR
register instead. In general this is easy to set up in the device tree,
thanks to the standard reset controller API.
However, to conform to the specifications of the PHY the reset signal
should be asserted for at least 10 us. This is handled correctly on
MSM8916 in ci_hdrc_msm_por_reset(), but not within the GCC driver.
Fix this by making use of the new "udelay" field of qcom_reset_map
and set a delay of ~15 us between the assertion/deassertion of the
USB PHY reset signal.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220706134132.3623415-5-stephan.gerhold@kernkonzept.com
The amount of time required between asserting and deasserting the reset
signal can vary depending on the involved hardware component. Sometimes
1 us might not be enough and a larger delay is necessary to conform to
the specifications.
Usually this is worked around in the consuming drivers, by replacing
reset_control_reset() with a sequence of reset_control_assert(), waiting
for a custom delay, followed by reset_control_deassert().
However, in some cases the driver making use of the reset is generic and
can be used with different reset controllers. In this case the reset
time requirement is better handled directly by the reset controller
driver.
Make this possible by adding an "udelay" field to the qcom_reset_map
that allows setting a different reset delay (in microseconds).
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220706134132.3623415-4-stephan.gerhold@kernkonzept.com
Split and extend existing CLK_AIF_OSR_DIV macro to implement mi2s
clocks. This simplifies the driver and removes extra code duplication.
The clock mi2s_div_clk used .enable_reg/.enable_bit, however these
fields are not used with by the clk_regmap_div_ops, thus they are
silently dropped. Clock enablement is handled in the mi2s_bit_div_clk
clock.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: David Heidelberg <david@ixit.cz> # tested on Nexus 7 (2013)
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220623120418.250589-6-dmitry.baryshkov@linaro.org
The Snapdragon 670 adds and removes some clocks, adds new frequencies, and
adds a new GPLL (Global Phase-Locked Loop) in reference to SDM845, while
also removing some GDSCs. Despite these differences, there are many
similarities with SDM670. Add data for SDM670 in the driver for SDM845 to
reuse the most of the clock data.
Advantages and disadvantages of this approach:
+ maintenance applies to both sdm670 and sdm845 by default
+ less duplicate code (clocks) means smaller distro/pre-built kernels
with all drivers enabled
- clocks for both SoC's must be compiled if the user wants clocks for one
specific SoC (both or none)
- additional testing needed for sdm845 devices
Link: 443bd8d6e2%5E%21/#F10
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220914013922.198778-4-mailingradian@gmail.com
The clock gating control for TX/RX/WSA core bus clocks would be required
to be reset(moved from hardware control) from audio core driver. Thus
add the support for the reset clocks.
Update the lpass_aon_cc_main_rcg_clk_src ops to park the RCG at XO after
disable as this clock signal is used by hardware to turn ON memories in
LPASS. Also add the external mclk to interface external MI2S.
Fixes: a9dd26639d ("clk: qcom: lpass: Add support for LPASS clock controller for SC7280")
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/1662005846-4838-6-git-send-email-quic_c_skakit@quicinc.com
In commit 3f905469c8 ("clk: qcom: gcc: Use floor ops for SDCC clocks")
floor ops were applied to SDCC2 only, but flooring is also required on
the SDCC1 apps clock which is used by the eMMC card on Sony's Nile
platform, and otherwise result in the typicial "Card appears
overclocked" warnings observed on many other platforms before:
mmc0: Card appears overclocked; req 52000000 Hz, actual 100000000 Hz
mmc0: Card appears overclocked; req 52000000 Hz, actual 100000000 Hz
mmc0: Card appears overclocked; req 104000000 Hz, actual 192000000 Hz
Fixes: f2a76a2955 ("clk: qcom: Add Global Clock controller (GCC) driver for SDM660")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Tested-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220714203822.186448-1-marijn.suijten@somainline.org
Use ARRAY_SIZE() instead of manually specifying num_parents. This makes
adding/removing entries to/from parent_data easy and errorproof.
This conversion fixes an issue present since the first version of this
driver. For the gp1_clk_src, gp2_clk_src and gp3_clk_src it was
impossible to select sleep_clk as a prent of the clock, since
num_parents was limited to 3 rather than 4. Switching to use num_parents
automatically makes sleep_clk available for selection.
Fixes: 3966fab8b6 ("clk: qcom: Add MSM8916 Global Clock Controller support")
Cc: Georgi Djakov <djakov@kernel.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20220704172453.838303-4-dmitry.baryshkov@linaro.org
