MALL SS and Subvp use the same calculations for determining the size of
the required allocation for a given surface, which is already done in
DML. Add an interface to extract this information from VBA variables and
use in their respective helper functions. Also refactor existing code to
remove stale workarounds.
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Two issues existed:
1) Configs that support DRR, but have it disabled will fail subvp+vblank
validation incorrectly. Use subvp+vblank path for this case.
2) Configs that support DRR and have it enabled can use higher voltage level
than required if they also support subvp+vblank. Use lowest supported voltage
level for this case.
Tested-by: Daniel Wheeler <Daniel.Wheeler@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SwathSizePerSurfaceY[] and SwathSizePerSurfaceC[] values are uninitialized
because we are using += instead of = operator.
[How]
Assign values in loop with = operator.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Subvp portion validation currently assumes that if vlevel provided does not
support pstate, then none will, and so subvp is not used.
[HOW]
After get vlevel, use lowest vlevel that supports pstate if it
exists, and use that for subvp validation.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- When merging a pipe that was previously pipe split, we need
to also clear the link resources or the next stream/plane that
uses the pipe may have an incorrect link resource state
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- FW scheduling algorithm doesn't take into account of it's
a center timing
- This affects where the subvp mclk switch can be scheduled
(prevents HUBP vline interrupt from coming in if scheduled
incorrectly)
- Block subvp center timing cases for now
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Iterating over every voltage state when we need to validate thousands of
configurations all at once (i.e. display hotplug) can take a significant
amount of time.
[How]
Check just the highest voltage state when fast_validate is true to
verify whether the configuration can work at all, then do a proper
validation including all voltage states later when fast_validate is false.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
LinkCapacitySupport array is indexed with the number of voltage states and
not the number of max DPPs. Fix the error by changing the array
declaration to use the correct (larger) array size of total number of
voltage states.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- This is a workaround to avoid concurrency issues -- a fast update
creates a shallow copy of the dc current_state, and removes all
subvp/phantom related flags.
- We want to prevent the fast update thread from removing those
flags in case there's another thread running that requires
the info for proper programming
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The 'commit 52e4fdf09ebc ("drm/amd/display: use low clocks for no plane
configs")' introduced a change that set low clock values for DCN31 and
DCN32. As a result of these changes, DC started to spam the log with the
following warning:
------------[ cut here ]------------
WARNING: CPU: 8 PID: 1486 at
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn20/dcn20_dccg.c:58
dccg2_update_dpp_dto+0x3f/0xf0 [amdgpu]
[..]
CPU: 8 PID: 1486 Comm: kms_atomic Tainted: G W 5.18.0+ #1
RIP: 0010:dccg2_update_dpp_dto+0x3f/0xf0 [amdgpu]
RSP: 0018:ffffbbd8025334d0 EFLAGS: 00010206
RAX: 00000000000001ee RBX: ffffa02c87dd3de0 RCX: 00000000000a7f80
RDX: 000000000007dec3 RSI: 0000000000000000 RDI: ffffa02c87dd3de0
RBP: ffffbbd8025334e8 R08: 0000000000000001 R09: 0000000000000005
R10: 00000000000331a0 R11: ffffffffc0b03d80 R12: ffffa02ca576d000
R13: ffffa02cd02c0000 R14: 00000000001453bc R15: ffffa02cdc280000
[..]
dcn20_update_clocks_update_dpp_dto+0x4e/0xa0 [amdgpu]
dcn32_update_clocks+0x5d9/0x650 [amdgpu]
dcn20_prepare_bandwidth+0x49/0x100 [amdgpu]
dcn30_prepare_bandwidth+0x63/0x80 [amdgpu]
dc_commit_state_no_check+0x39d/0x13e0 [amdgpu]
dc_commit_streams+0x1f9/0x3b0 [amdgpu]
dc_commit_state+0x37/0x120 [amdgpu]
amdgpu_dm_atomic_commit_tail+0x5e5/0x2520 [amdgpu]
? _raw_spin_unlock_irqrestore+0x1f/0x40
? down_trylock+0x2c/0x40
? vprintk_emit+0x186/0x2c0
? vprintk_default+0x1d/0x20
? vprintk+0x4e/0x60
We can easily trigger this issue by using a 4k@120 or a 2k@165 and
running some of the kms_atomic tests. This warning is triggered because
the per-pipe clock update is not happening; this commit fixes this issue
by ensuring that DPPCLK is updated when calculating the watermark and
dlg is invoked.
Fixes: 2641c7b780 ("drm/amd/display: use low clocks for no plane configs")
Reported-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
When calculating watermark and dlg values, the max mclk level index and
associated speed are needed to find the correlated dummy latency value.
Currently the incorrect index is given due to a clock manager refactor.
[HOW?]
Use num_memclk_level from num_entries_per_clk struct for getting the correct max
mem speed.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Some configurations are constructed with very marginal DET buffers relative to
the worst possible time required to fetch a swath.
[HOW?]
Add a check to see that the DET buffer allocated for each pipe can hide the
latency for all pipes to fetch at least one swath.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Prefetch is not budgetting time for dummy pstate when using subvp and low uclk.
[HOW?]
Override fclk change latency to use dummy pstate latency when calculating
prefetch schedule for subvp configs with low uclk.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Even if we block Z9 based on crossover threshold it's possible to
allow for Z8.
[How]
There's support for this on DCN314, so update the support types to
include a z8 only and z8_z10 only state.
Update the decide_zstate_support function to allow for specifying
these modes based on the Z8 threshold.
DCN31 has z-state disabled, but still update the legacy code to
map z8_only = disallow and z10_z8_only = z10_only to keep the support
the same.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is used to fix following compilation issue with legacy gcc
error: ‘for’ loop initial declarations are only allowed in C99 mode
for (int i = flag_vlevel; i < context->bw_ctx.dml.soc.num_states; i++) {
Signed-off-by: Bob zhou <bobzhou2@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
DCN32 uses fclk pstate watermarks for dummy pstate, and must always be
supported.
[HOW?]
Validation needs to be run with fclk pstate latency set
as the dummy pstate latency to get correct prefetch and bandwidth outputs.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- If we're enabling phantom pipe for a high
link rate display we could
fail DML on the phantom pipe since it's
set to virtual signal
- Therefore don't consider Output BPP for
phantom pipe
Reviewed-by: Dillon Varone <Dillon.Varone@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Subvp src/dst stream rectangles are not being created with the same scaling
factors as the main stream.
[HOW?]
Make sure subvp stream src rectangle scales its height to have the same src/dst
ratio as the main stream.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
After applying pipesplit flags, DML can select a different configuration upon
revalidation, despite the desired one still being valid.
[HOW?]
Check the configuration is still has mode support, and apply it.
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain high resolution displays exhibit DCC line corruption with SubVP
enabled. This is likely due to insufficient DCC meta data buffered
immediately after the mclk switch.
[How]
Add workaround to increase phantom pipe vactive height by
meta_row_height number of lines, thus increasing the amount of meta data
buffered immediately after mclk switch finishes.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN3.2 DML logic uses a new output type for DP2.0,
which will enable validation to pass for higher BW
timings that require DP2.0 link rates.
[How]
Populate the DML pipe with DP2.0 output type if
the signal type of the pipe_ctx is 128b/132b.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Jasdeep Dhillon <jasdeep.dhillon@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Data return times when using lowest memclk can be <= 60us, which can cause
underflow on high bandwidth displays with a workload.
[HOW?]
Enforce a minimum prefetch time during validation for low memclk modes.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Recent backports from open source do not have header inclusion pattern
that is consistent with inclusion style in the rest of the file. This
breaks the internal tool builds as well. A recent commit erronously
modified the original DML formula for calculating
ActiveClockChangeLatencyHidingY. This resulted in a FCLK deviation
from the golden values.
[How]
Change the way in which display_mode_vba.h is included so that it is
consistent with the inclusion style in rest of the file which also fixes
the tool build. Restore the DML formula to its original state to fix the
FCLK deviation.
Reviewed-by: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We're missing the helpers from dcn20 that would allow
overriding these with DC debug options.
[How]
Use dcn20_patch_bounding_box to support overriding all the
relevant values.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After moving all FPU code to the DML folder, we can enable DCN support
for the ARM64 platform. Remove the -mgeneral-regs-only CFLAG from the
code in the DML folder that needs to use hardware FPU, and add a control
mechanism for ARM Neon.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Ao Zhong <hacc1225@gmail.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Fix for some of the tool reported modes for FCLK
P-state deviations and UCLK P-state deviations that
are coming from DSC terms and/or Scaling terms
causing MinActiveFCLKChangeLatencySupported
and MaxActiveDRAMClockChangeLatencySupported
incorrectly calculated in DML for these configurations.
Reviewed-by: Chaitanya Dhere <Chaitanya.Dhere@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain 4K high refresh rate modes requiring DSC are exhibiting top
of screen underflow corruption. Increasing the DSC delay by a factor
of 6 percent stops the underflow for most use cases.
[How]
Multiply DSC delay requirement in DML by a factor.
Add debug option to make this DSC delay factor configurable.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC config is calculated separately from DML calculations.
DML should use these separately calculated DSC params. The issue is
that the calculated bpp is not properly propagated into DML.
[How]
Correctly used forced_bpp value in DML.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN32 DSC delay calculation had an unintentional integer division,
resulting in a mismatch against the DML spreadsheet.
[How]
Cast numerator to double before performing the division.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
