Previously we would call apply_ctx_to_hw to enable and disable
phantom pipes. However, apply_ctx_to_hw can potentially update
non-phantom pipes as well which is undesired. Instead of calling
apply_ctx_to_hw as a whole, call the relevant helpers for each
phantom pipe when enabling / disabling which will avoid us modifying
hardware state for non-phantom pipes unknowingly.
The use case is for an FRL display where FRL_Update is requested
by the display. In this case link_state_valid flag is cleared in
a passive callback thread and should be handled in the next stream /
link update. However, due to the call to apply_ctx_to_hw for the
phantom pipes during a flip, the main pipes were modified outside
of the desired sequence (driver does not handle link_state_valid = 0
on flips).
Cc: stable@vger.kernel.org # 6.6+
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Timings with small HBlank (such as CVT RBv2) can result in insufficient
HBlank bandwidth for audio SDP transmission when DSC is active. This
will cause some higher bandwidth audio modes to fail.
The combination of CVT RBv2 timings + DSC can commonly be encountered
in MST scenarios.
[How]
Add DP audio bandwidth validation for 8b/10b MST and 128b/132b SST/MST
cases and filter out modes that cannot be supported with the current
timing config.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Panels show corruption with high refresh rate timings when ssc is
enabled.
[How]
Read down-spread percentage from lut to adjust dprefclk. Issues come
from S0i3 with this commit has been fixed by SMU.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
BL1_PWM_USER_LEVEL is meant for the user brightness level setting from
OS. However, we update it along with other ABM levels to the real PWM
value which could be ABMed.
[How]
Driver to cache and restore the user brightness level setting so that
DMUB can retrieve the last user setting in ABM config initialization.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Camille Cho <camille.cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
There is a corner case where the symclk otg flag is cleared
when disabling the phantom pipe for subvp (because the phantom
and main pipe share the same link). This is undesired because
we need the maintain the correct symclk otg flag state for
the main pipe.
For now only clear the flag only for HDMI signal type, since
it's only set for HDMI signal type (phantom is virtual). The
ideal solution is to not clear it if the stream is phantom but
currently there's a bug that doesn't allow us to do this. Once
this issue is fixed the proper fix can be implemented.
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Phantom streams and planes were previously not referenced explcitly on creation.
[HOW?]
To reduce memory management complexity, add an additional phantom streams and planes
reference into dc_state, and move mall_stream_config to stream_status inside
the state to make it safe to modify in shallow copies. Also consildates any logic
that is affected by this change to dc_state.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Part of the dc_state interface that deals with adding streams and planes should
remain public, while others that deal with internal status' and subvp should be
private to DC.
[HOW?]
Move and rename the public functions to dc_state.h and private functions to
dc_state_priv.h. Also add some additional functions for extracting subvp meta
data from the state.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
OTG inst and pwrseq inst mapping is not align therefore we cannot use
otg_inst as pwrseq inst to get DCIO register.
[How]
1. Pass the correct pwrseq instance to dmub when set abm pipe.
2. LVTMA control index change from panel_inst to pwrseq_inst.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Phil Hsieh <phil.hsieh@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Lewis Huang <lewis.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Rename hw_sequencer to hwseq.
Move all hwseq files to unique
folder hwss.
[how]
creating hwss repo in dc, and moved the dcnxx_hwseq.c
and .h files into corresponding new folders inside the hwss
and cleared the linkage errors by adding relative paths
in the Makefile.template.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Mounika Adhuri <moadhuri@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
