[why]
There is only a single call to dc_post_update_surfaces_to_stream so
there is no need to have two flags to control it. Unifying this to a
single flag allows dc_stream_adjust_vmin_vmax to skip actual
programming when there is no change required.
[how]
Remove wm_optimze_required flag and set only optimize_required in its
place. Then in dc_stream_adjust_vmin_vmax, check that the stream timing
range matches the requested one and skip programming if they are equal.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- When we're in a no plane config, DCN is always asserting
P-State allow
- This creates a scenario where the P-State blackout can start
just as VUPDATE takes place and transitions the DCN config to
a one where one or more HUBP's are active which can result in
underflow
- To fix this issue, force p-state disallow and unforce after
the transition from no planes case -> one or more planes active
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Current implementation will choose to use refclk as dscclk. This is not
recommended by hardware team as refclk is a fixed value which could
cause unnecessary power consumption or it could be not enough for large
DSC timings. So we are adding new interfaces so we could switch to use
dynamically generated DSCCLK by DTO. So DSCCLK is programmable based on
current pixel clock and dispclk.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
OTG inst and pwrseq inst mapping is not align therefore we cannot use
otg_inst as pwrseq inst to get DCIO register.
[How]
1. Pass the correct pwrseq instance to dmub when set abm pipe.
2. LVTMA control index change from panel_inst to pwrseq_inst.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Phil Hsieh <phil.hsieh@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Lewis Huang <lewis.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Similar to FPO, SubVP should also force cursor P-State
allow instead of relying on natural assertion
- Implement code path to force and unforce cursor P-State
allow for SubVP
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
LUT params are not cleared after setting blend TF, which can lead to
same params being used for the shaper, if the shaper func is bypassed.
[How]
Set lut_params to NULL after program_1dlut.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Ilya Bakoulin <ilya.bakoulin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Helper function calculates num_ways using 32-bit. But is
returned as 8-bit. If num_ways exceeds 8-bit, then it
reports back the incorrect num_ways and erroneously
uses MALL when it should not
[How]
Make returned value 32-bit and convert after it checks
against caps.cache_num_ways, which is under 8-bit
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Intermittent reboot hangs are observed introduced by
"Improve x86 and dmub ips handshake".
[How]
Bring back the commit but fix the polling.
Avoid hanging in place forever by bounding the delay and ensure that
we still message DMCUB on IPS2 exit to notify driver idle has been
cleared.
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Need a helper function to check idle power is allowed
so that dc doesn't access any registers that are power-gated.
[how]
Implement helper function to check idle power optimization.
Enable a hook to check if detection is allowed.
V2:
Add function hooks for set and get idle states.
Check if function hook was properly initialized.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nicholas Choi <nicholas.choi@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Sung Joon Kim <sungkim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During system boot in second screen only mode on a seamless boot system,
there is a chance that the pipe's det size might not be reset.
[How]
Reset the det size while resetting the pipe during seamless boot.
Reviewed-by: Dmytro Laktyushkin <dmytro.laktyushkin@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current DPG test pattern logic does not account for ODM configuration
changes after test pattern has already been programmed. For example, if
ODM2:1 is enabled after test pattern is already being output, the second
pipe is not programmed to output test pattern, causing half the screen
to be black.
[How]
Move DPG test pattern parameter calculations into separate function.
Whenever ODM pipe configuration changes, re-calculate DPG test pattern
parameters and program DPG if test pattern is currently enabled.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Rename hw_sequencer to hwseq.
Move all hwseq files to unique
folder hwss.
[how]
creating hwss repo in dc, and moved the dcnxx_hwseq.c
and .h files into corresponding new folders inside the hwss
and cleared the linkage errors by adding relative paths
in the Makefile.template.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Mounika Adhuri <moadhuri@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
