[why]
The feature was disabled due to regression found during testing. Now
that all the pending issues are addressed, we are reenabling the power
saving feature again.
The feature optimizes dispclk level when user is using MPO capable
broswers or watching MPO capable videos in windowed mode. The feature
achieves power optimization by utilizing free pipes to process incoming
pixels in parallel. So it reduces max dispclk requirements for each
pipe.
Previously ODM power optimization will be disabled when MPO plane is
present due to technical challeges. This is mainly because ODM divides
pixel workload with respect to stream but MPO plane position and size
are arbitrary with respect to stream. The pixel processing workload of
an MPO plane is not guarenteed to be evenly distributed across DCN pipes.
For example if a plane is moved inside single ODM slice, all the
processing for the plane is distributed to the pipe in the current ODM
slice, while the other ODM slices don't need to process this plane. If
the plane is then moved to the middle crosing two ODM slices, each ODM
slice gets half of the workload. This is especially difficult when the
plane itself has a large source rect which can't be processed by single
DCN pipe. In this case we can't enable ODM power optimization when the
plane is only within one ODM slice.
[how]
To overcome the challeges, new pipe resource management is in place to
make sure a plane is validated with ODM power optimization support if
it can be validated regardless of its position and the same pipe
topology can be used regardless of the plane's position. When the plane
is moved outside current ODM slice, we will set recout to 0 so the pipe
can be idling without the need to update pipe topology. When the user
resizes a plane, it may result in downscaling ratio changes. When the
downscaling ratio is above single pipe's threshold, we will seamlessly
exit ODM power optimization and applies MPC combine to support the plane.
when downscaling ratio becomes smaller, we will seamlessly enter ODM
power optimization again. All these pipe transitions happen
automatically and quietly when the conditions are met without any visual
impacts to the user.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When populating dml pipes, odm combine policy should be assigned based
on the pipe topology of the context passed in. DML pipes could be
repopulated multiple times during single validate bandwidth attempt. We
need to make sure that whenever we repopulate the dml pipes it is always
aligned with the updated context. There is a case where DML pipes get
repopulated during FPO optimization after ODM combine policy is changed.
Since in the current code we reinitlaize ODM combine policy, even though
the current context has ODM combine enabled, we overwrite it despite the
pipes are already split. This causes DML to think that MPC combine is
used so we mistakenly enable MPC combine because we apply pipe split
with ODM combine policy reset. This issue doesn't impact non windowed
MPO with ODM case because the legacy policy has restricted use cases. We
don't encounter the case where both ODM and FPO optimizations are
enabled together. So we decide to leave it as is because it is about to
be replaced anyway.
Cc: stable@vger.kernel.org # 6.6+
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
For FPO and SubVP/DRR cases we need to ensure to program
OTG_V_TOTAL_MIN/MAX_SEL, otherwise stretching the vblank
in FPO / SubVP / DRR cases will not have any effect
and we could hit underflow / corruption.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For FPO and SubVP/DRR cases we need to ensure to program
OTG_V_TOTAL_MIN/MAX_SEL, otherwise stretching the vblank in FPO / SubVP
/ DRR cases will not have any effect and we could hit underflow /
corruption.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In DCN32/321 FPO uses per-pipe P-State force. If there is no plane, then
then HUBP is power gated, in which case any programming in HUBP has no
effect and the pipe is always asserting P-State allow. This is contrary
to what we want to happen for FPO (FW should moderate the P-State
assertion), so block FPO if there's no plane for the FPO pipe.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Reviewed-by: Samson Tam <samson.tam@amd.com>
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Phantom streams and planes were previously not referenced explcitly on creation.
[HOW?]
To reduce memory management complexity, add an additional phantom streams and planes
reference into dc_state, and move mall_stream_config to stream_status inside
the state to make it safe to modify in shallow copies. Also consildates any logic
that is affected by this change to dc_state.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY?]
Part of the dc_state interface that deals with adding streams and planes should
remain public, while others that deal with internal status' and subvp should be
private to DC.
[HOW?]
Move and rename the public functions to dc_state.h and private functions to
dc_state_priv.h. Also add some additional functions for extracting subvp meta
data from the state.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When querying DML for a vlevel after pipes have been split or merged the
ODM policy would revert to a default policy, which could cause the query
to use the incorrect ODM status. In this case ODM 2to1 was validated,
but the last DML query would assume no ODM and return the incorrect
vlevel.
[how]
Added ODM check to apply the correct ODM policy before querying DML.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Relja Vojvodic <relja.vojvodic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Previously SubVP would never be selected on 1080p60 displays because
it has too much vactive margin. However, implement a change to allow
it like how 1440p60 is allowed.
- Add a new struct such that we have a list of allowed modes for
enabling subvp with vactive margin (currently 1080p60 and 1440p60)
- Also ensure to block drr + vblank cases to prevent unexpected
enablement of new display configs
- Update SW cursor fallback for these new potential cases as well
Reviewed-by: Samson Tam <samson.tam@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Move all resource files to unique folder resource.
[HOW]
Created resource folder in dc, moved the
dcnxx_resource.c and dcnxx_resource.h files into
corresponding new folders inside the resource and
made appropriate changes for compilation in Makefiles.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mounika Adhuri <moadhuri@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
